Repara tus cosas Comunidad Tienda

Replacing VTech MobiGo Touch Learning System Speaker

Introducción

This page is for disassembling the speaker inside the device. Before following these steps, please refer to the Disassembling VTech MobiGo Touch Learning System Case Guide first.

Qué necesitas

  1. Replacing VTech MobiGo Touch Learning System Speaker, Case: paso 1, imagen 1 de 1

    • Remove the battery covers and the four batteries.

    Editar

  2. Replacing VTech MobiGo Touch Learning System Speaker: paso 2, imagen 1 de 2 Replacing VTech MobiGo Touch Learning System Speaker: paso 2, imagen 2 de 2

    • Remove the four plastic caps with a metal spudger to expose the 6.0 mm Philips JIS #0 case screws.

    • Remove the eight 6.0 mm JIS #0 case screws.

    Editar

  3. Replacing VTech MobiGo Touch Learning System Speaker: paso 3, imagen 1 de 2 Replacing VTech MobiGo Touch Learning System Speaker: paso 3, imagen 2 de 2

    • Using a plastic opening tool, separate the two pieces of the case carefully.

    Editar

  5. Replacing VTech MobiGo Touch Learning System Speaker, Speaker: paso 4, imagen 1 de 2 Replacing VTech MobiGo Touch Learning System Speaker, Speaker: paso 4, imagen 2 de 2

    • The speaker will be attached to the back of the case.

    • Unscrew the two 6.0 mm Philips J0 screws.

    • Careful! The wires are still attached to the back of the case and to the speakers.

    Editar

  6. Replacing VTech MobiGo Touch Learning System Speaker: paso 5, imagen 1 de 2 Replacing VTech MobiGo Touch Learning System Speaker: paso 5, imagen 2 de 2

    • Lift the round speaker with a plastic opening tool.

    • Remove the two wires connected to the speaker.

    • You can use wire cutters or regular needle nose pliers to disconnect the wires from the speaker.

    • Once the wires are disconnected, remove the speaker from the back of the case.

    Editar

  7. Replacing VTech MobiGo Touch Learning System Speaker: paso 6, imagen 1 de 2 Replacing VTech MobiGo Touch Learning System Speaker: paso 6, imagen 2 de 2

    • Solder the wires to the appropriate spots on the new speaker, making sure that both wires are properly connected.

    • The wires may be hot.

    Editar

  8. Replacing VTech MobiGo Touch Learning System Speaker: paso 7, imagen 1 de 2 Replacing VTech MobiGo Touch Learning System Speaker: paso 7, imagen 2 de 2

    • Insert the new speaker into the hatch located in the middle part of the panel using a plastic spudger.

    • Make sure the speaker is the right size for the panel.

    • Once the speaker is properly placed, screw in the two 6.0 mm Philips J0 screws.

    • Do not over tighten the screws or the panel will break.

    Editar
Conclusión

To reassemble your case, follow the case instructions in reverse order.

Autor

con 3 otros colaboradores

RBansil

Miembro Desde 08/27/15

221 Reputación

2 Guías creadas

Insignias: 6

+ 3 más insignias

Equipo

USF Tampa, Team 8-3, Eyestone Fall 2015 Miembro de USF Tampa, Team 8-3, Eyestone Fall 2015

USFT-EYESTONE-F15S8G3

3 Miembros

17 Guías creadas

0 comentarios

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 0

Ultimos 7 días: 1

Ultimos 30 días: 5

Todo El Tiempo: 1,365