Saltar al contenido principal

Introducción

The battery stores the power that enables the device to run.

Partes

No se especificaron partes.

  1. Using a spudger, wedge the tip between the front and back case to pry them apart. Be careful to not apply excessive force since there are six fasteners on the screen's side that holds the cases firmly together. Be careful to not apply excessive force since there are six fasteners on the screen's side that holds the cases firmly together.
    • Using a spudger, wedge the tip between the front and back case to pry them apart.

    • Be careful to not apply excessive force since there are six fasteners on the screen's side that holds the cases firmly together.

  2. The black rubber button pad can be removed by simply picking it up.
    • The black rubber button pad can be removed by simply picking it up.

  3. Flip the LCD screen off the midsection plate to gain access to the space around the input button chip.
    • Flip the LCD screen off the midsection plate to gain access to the space around the input button chip.

  4. Kits de Reparación de Android

    Estás a un kit de tu nueva pantalla o batería.

    Comprar Ahora

    Kits de Reparación de Android

    Estás a un kit de tu nueva pantalla o batería.

    Comprar Ahora
  5. Using a spudger, pry off the button input chip from the mid-section of the device. To gain best leverage, start at the bottom right corner and level your way up the side of the chip.
    • Using a spudger, pry off the button input chip from the mid-section of the device. To gain best leverage, start at the bottom right corner and level your way up the side of the chip.

    • Be aware that the button input chip is glued to the mid-section, so some extra force may be required.

  6. Lift open the LCD screen and button input chip to access the entire midsection plate.
    • Lift open the LCD screen and button input chip to access the entire midsection plate.

  7. Use a Phillips Head screwdriver to unscrew the three 3/16 inch screws that were underneath the button input chip.
    • Use a Phillips Head screwdriver to unscrew the three 3/16 inch screws that were underneath the button input chip.

  8. Use a Phillips Head screwdriver to unscrew the three 3/16 inch screws that were underneath the LCD screen.
    • Use a Phillips Head screwdriver to unscrew the three 3/16 inch screws that were underneath the LCD screen.

  9. Use a spudger to pry the battery from the midsection plate.
    • Use a spudger to pry the battery from the midsection plate.

    • There is adhesive glue underneath the battery, so additional force might be required to separate the battery.

  10. Locate the soldering joint connecting the battery wires to the power supply, marked by the letters "PS" on the motherboard. Hold the battery wires in place so that access to the soldering joints is not blocked.
    • Locate the soldering joint connecting the battery wires to the power supply, marked by the letters "PS" on the motherboard.

    • Hold the battery wires in place so that access to the soldering joints is not blocked.

    • When using a soldering iron, keep your hands and fingers as far as possible from the iron's tip to avoid burning your skin.

    • Using a soldering iron, melt the solder connecting the red wire to the motherboard. Do the same action to the black wire.

Conclusión

To reassemble your device, follow these instructions in reverse order.

3 personas más completaron esta guía.

Westley Courchene

Miembro Desde 13/01/15

3,060 Reputación

14 Guías creadas

Equipo

USF Tampa, Team 1-1, Remmell Fall 2015 Miembro de USF Tampa, Team 1-1, Remmell Fall 2015

USFT-REMMELL-F15S1G1

5 Miembros

14 Guías creadas

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 2

Ultimos 7 días: 10

Ultimos 30 días: 47

Todo El Tiempo: 2,932