Saltar al contenido principal

Introducción

Stalled printer for error 0xF2 or 0xF3

This error happens when there are some problems with the encoder when the roller tries to move paper.

Partes

No se especificaron partes.

  1. Remove the paper tray Remove the paper cassette Remove Ink tanks
    • Remove the paper tray

    • Remove the paper cassette

    • Remove Ink tanks

  2. Remove the opening covers Remove the opening covers
    • Remove the opening covers

  3. Remove the rear component
    • Remove the rear component

  4. Dismount the Ink lever
    • Dismount the Ink lever

  5. Remove the front panel screws Remove the front panel screws
    • Remove the front panel screws

  6. Dismount LCD Panel Dismount LCD Panel
    • Dismount LCD Panel

  7. Remove the front panel Remove the front panel Remove the front panel
    • Remove the front panel

  8. Remove the back panel screws Remove the back panel screws Remove the back panel screws
    • Remove the back panel screws

  9. Remove the last back panel screw (hidden behind the LCD display) Remove the last back panel screw (hidden behind the LCD display)
    • Remove the last back panel screw (hidden behind the LCD display)

  10. Remove the back ethernet panel
    • Remove the back ethernet panel

  11. Remove the main back panel, being careful not to damage the LCD display Remove the main back panel, being careful not to damage the LCD display Remove the main back panel, being careful not to damage the LCD display
    • Remove the main back panel, being careful not to damage the LCD display

  12. Clean the left roller very gently with a dry tissue or a soft brush Clean the left roller very gently with a dry tissue or a soft brush
    • Clean the left roller very gently with a dry tissue or a soft brush

  13. Clean right encoder very gently with a dry tissue or a soft brush. Clean right encoder very gently with a dry tissue or a soft brush. Clean right encoder very gently with a dry tissue or a soft brush.
    • Clean right encoder very gently with a dry tissue or a soft brush.

  14. If you want to test the printer you need to insert paper, and cover 2 switches with tape. If you want to test the printer you need to insert paper, and cover 2 switches with tape.
    • If you want to test the printer you need to insert paper, and cover 2 switches with tape.

  15. Reassemble the printer (remove the tape first if you have used it) following these instructions in reverse.
    • Reassemble the printer (remove the tape first if you have used it) following these instructions in reverse.

Conclusión

To reassemble your device, follow these instructions in reverse order.

16 personas más completaron esta guía.

delete

Miembro Desde 15/11/12

541 Reputación

1 Guía escrita

It's works, thanks

Thom - Contestar

Perfect. I used this guide to disassemble my printer.

I had 0xF1 and/or 0xF4. The reason was some paper stuck between the gears of the paper feed (in this guide step 12).

I hope this hint will help others. I didn't find any info about these error code online.

DumahBrazorf - Contestar

Error descriptions I found here - http://www.fatalerrors.info/

John Smith -

Thank you very much ! This is a very useful and beautifully documented guide. Best wishes and greetings to the kind author of this guide from Bratislava, Slovakia.

George Pekarovic

George - Contestar

muito obrigado pela ajuda

Filipe Rocha - Contestar

You are awesome! It helped me! Thanks very much!

martinjurtik - Contestar

Hi

I keep getting on an Epson B-500DN printer error restart printer with the paper and ink led blinking orange.

Disassemble the printer made a full cleaning (all encoding wheels too) and keep getting this error, the printer goes until ready, then as soon as it says printing it shows the error.

anyone ???

invitro59 - Contestar

OMG.

I had error oxF3.

I was set to bin this ace printer, I just googled the error code and bam this guide came up. This was awesome, I only found a little dirt on the step 12 clear plastic disc, nothing visible on step 13. Put the cartridges back in, maintenance tank paper tray and hooked up the power and network cable, and covered the 2 switches with tape. then OMG it worked. Now need to work out which screw goes where and reassemble.

Malcolm Taylor - Contestar

OK. Seguito con semplicità e Risolto il Problema. Adesso funziona. OK Thank you

Foto Diego - Contestar

What about Erro code 0xF3 in Epson WF7610

ABEL MLIGA - Contestar

Yes what about the WF7610 error code 0xF3?!

David Imondi - Contestar

I have Epson XP 710 which shows an error code 0×4f what can i do for it. When i turned it on it's starts well with Epson logo but there's a sound of running the gears in fast speed for a few seconds after this it's showing the error just after pooping up the menu screen no head movement. Kindly forward me with possible assistance

abab6330 - Contestar

Constantly gives 0xF4. If you move the head to the center, when it is turned on, it goes to the left, then goes to its place and when Parking the engine PF PID (left) twitches a little, and the scoreboard error 0xF4. In printer all cleaned up, blew. Cartridges took out, got a diaper. Before that, it was so that it prints, then outputs 0xF4 and sometimes 0xF1. What to do?

561054 - Contestar

Works very good. The photos for the right sight could be better, but when you know how it looks on the left its possible to find.

Ralf Sagorny

Ralf Sagorny - Contestar

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 0

Ultimos 7 días: 15

Ultimos 30 días: 103

Todo El Tiempo: 56,452