Saltar al contenido principal

Esta versión puede contener ediciones incorrectas. Cambiar a la última instantánea verificada.

Qué necesitas

  1. Este paso está sin traducir. Ayuda a traducirlo

    : paso 1, imagen 1 de 3 : paso 1, imagen 2 de 3 : paso 1, imagen 3 de 3
    • Locate the large button on the top of the device.

    • Push down on the button and slide the cover away from the button.

    • The battery removal tab may pop up.

  2. Este paso está sin traducir. Ayuda a traducirlo

    : paso 2, imagen 1 de 3 : paso 2, imagen 2 de 3 : paso 2, imagen 3 de 3
    • Grab the red pull tab and pull down to unlock the latch.

    • Pull the battery out.

  3. Este paso está sin traducir. Ayuda a traducirlo

    : paso 3, imagen 1 de 2 : paso 3, imagen 2 de 2
    • Remove the four screws from the bottom of the device using a T6 Torx screwdriver.

  4. Este paso está sin traducir. Ayuda a traducirlo

    : paso 4, imagen 1 de 3 : paso 4, imagen 2 de 3 : paso 4, imagen 3 de 3
    • Remove the button cover on the back of the device by prying it up with a spudger or your thumb nail.

  5. Este paso está sin traducir. Ayuda a traducirlo

    : paso 5, imagen 1 de 3 : paso 5, imagen 2 de 3 : paso 5, imagen 3 de 3
    • Remove the two screws under the button using the T6 Torx screwdriver.

  6. Este paso está sin traducir. Ayuda a traducirlo

    : paso 6, imagen 1 de 2 : paso 6, imagen 2 de 2
    • Remove the back cover.

  7. Este paso está sin traducir. Ayuda a traducirlo

    : paso 7, imagen 1 de 2 : paso 7, imagen 2 de 2
    • Remove the power button by pulling it to the left.

  8. Este paso está sin traducir. Ayuda a traducirlo

    : paso 8, imagen 1 de 2 : paso 8, imagen 2 de 2
    • Remove the plastic antenna extension connector on the right side of the device.

  9. Este paso está sin traducir. Ayuda a traducirlo

    : paso 9, imagen 1 de 3 : paso 9, imagen 2 de 3 : paso 9, imagen 3 de 3
    • Pull up on the motherboard to remove it from the device.

    • The LCD screen and keypad are only connected to the motherboard with ribbon cables. They will hang down as the motherboard is removed.

  10. Este paso está sin traducir. Ayuda a traducirlo

    : paso 10, imagen 1 de 2 : paso 10, imagen 2 de 2
    • The logic board must be exposed to begin.

    • Flip the device over (see second picture).

    • CAUTION: The keyboard is loosely attached by a ribbon cable and may move when the device is flipped.

  11. Este paso está sin traducir. Ayuda a traducirlo

    : paso 11, imagen 1 de 1
    • Lift up the keyboard carefully from the right side, flipping to the left.

    • NOTE: The keyboard is attached on the left side by a ribbon cable. Do not remove it completely yet.

  12. Este paso está sin traducir. Ayuda a traducirlo

    : paso 12, imagen 1 de 3 : paso 12, imagen 2 de 3 : paso 12, imagen 3 de 3
    • Pivot the LCD screen, pulling on the top and sides and keeping the bottom attached.

  13. Este paso está sin traducir. Ayuda a traducirlo

    : paso 13, imagen 1 de 3 : paso 13, imagen 2 de 3 : paso 13, imagen 3 de 3
    • Continue to pivot the screen until it is lying on its face.

    • Pivot the wire frame, that was under the LCD, from the left side.

    • CAUTION: The wire bends as the frame pivots. Use the least amount of force necessary.

  14. Este paso está sin traducir. Ayuda a traducirlo

    : paso 14, imagen 1 de 3 : paso 14, imagen 2 de 3 : paso 14, imagen 3 de 3
    • With the frame perpendicular to the device, locate the two black, plastic tabs shown in the two red circles.

    • The boxes show more detailed views in the following pictures.

  15. Este paso está sin traducir. Ayuda a traducirlo

    : paso 15, imagen 1 de 3 : paso 15, imagen 2 de 3 : paso 15, imagen 3 de 3
    • WIth both hands, pull the tabs outwards to release the plastic cover from the board.

    • Once the tabs are disengaged, pivot the plastic cover upwards.

    • After the cover is pivoted slightly, remove it from the device.

  16. Este paso está sin traducir. Ayuda a traducirlo

    : paso 16, imagen 1 de 2 : paso 16, imagen 2 de 2
    • After the plastic cover is removed, locate the white, ribbon connector highlighted by the red square.

    • Rotate the device 90 degrees counterclockwise to remove the ribbon connector.

  17. Este paso está sin traducir. Ayuda a traducirlo

    : paso 17, imagen 1 de 3 : paso 17, imagen 2 de 3 : paso 17, imagen 3 de 3
    • To remove the ribbon cable from the board, catch the sides of the connector with fingernails and pull downward.

    • CAUTION: The connector is delicate.

    • After the latch is pulled down, the ribbon cable is free to slide out of the connector housing.

  18. Este paso está sin traducir. Ayuda a traducirlo

    : paso 18, imagen 1 de 1
    • After following the prerequisite steps in the guide, the components are laid out as depicted in the picture.

    • The LCD screen is highlighted in red.

Linea de Meta

Aubrey

Miembro Desde 03/09/12

54 Reputación

3 Guías creadas

Equipo

Clemson, Team 1-2, Benson Spring 2012 Miembro de Clemson, Team 1-2, Benson Spring 2012

CLEM-BENSON-S12S1G2

3 Miembros

9 Guías creadas

0 comentarios

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 0

Ultimos 7 días: 0

Ultimos 30 días: 1

Todo El Tiempo: 1,929