Introducción

Usa esta guía para reemplazar el botón de inicio.

Ten en cuenta que solo el ensamblaje original del botón de inicio del teléfono podrá utilizar la funcionalidad Touch ID. "La instalación de un nuevo botón de inicio solo restaurará las funciones normales de los botones de inicio, no las funciones de Touch ID".

También puedes usar esta guía para reemplazar las siguientes partes:

Error

Enlace de servicio de video no reconocido.

Example:

[video|http://vimeo.com/1234] or [video|http://vimeo.com/1234]Optional Caption[/video]

Current text:

[video | https: //www.youtube.com/watch? v = 1-x8RO8eCLg]
  1. Antes de desmontar tu iPhone, descarga la batería por debajo del 25%. Una batería de iones de litio cargada puede incendiarse y / o explotar si se pincha accidentalmente.
    • Antes de desmontar tu iPhone, descarga la batería por debajo del 25%. Una batería de iones de litio cargada puede incendiarse y / o explotar si se pincha accidentalmente.

    • Apaga su iPhone antes de comenzar el desmontaje.

    • Retira los dos tornillos Pentalobe P2 de 3,6 mm junto al conector Lightning.

    I prefer to remove the SIM card as the very first step since it's safer to do so while the phone is fully assembled.

    estebanfallasf - Contestar

    I stripped one of the two screws - at a dead stop.

    Margaret Patterson - Contestar

  2. Los siguientes dos pasos demuestran el uso de iSclack, una gran herramienta para la segura apertura de el iPhone 6 Plus que recomendamos a cualquiera que haga mas de una reparación.  Si no estás usando el iSclack, salta al Paso 4 Si el medidor de profundidad de plástico está conectado en el centro del iSclack, sácalo ahora, no es necesario para teléfonos más grandes como el iPhone 6 Plus Cierra la manija en el iSclack, abriendo las mandíbulas de la ventosa.
    • Los siguientes dos pasos demuestran el uso de iSclack, una gran herramienta para la segura apertura de el iPhone 6 Plus que recomendamos a cualquiera que haga mas de una reparación. Si no estás usando el iSclack, salta al Paso 4

    • Si el medidor de profundidad de plástico está conectado en el centro del iSclack, sácalo ahora, no es necesario para teléfonos más grandes como el iPhone 6 Plus

    • Cierra la manija en el iSclack, abriendo las mandíbulas de la ventosa.

    • Coloca la parte inferior de su iPhone entre las ventosas.

    • Coloca la copa de succión superior del iSclack contra la pantalla, cerca del botón de inicio.

    • Abre las asas para cerrar las mandíbulas del iSclack. Centrar las ventosas y presionarlas firmemente en la parte superior e inferior del iPhone.

  3. Sostén tu iPhone firmemente y cierra el mango del iSclack para separar las ventosas, tirando del panel frontal hacia arriba desde la carcasa trasera. El iSclack está diseñado para abrir tu iPhone lo suficiente para separar las piezas con seguridad, pero no lo suficiente para dañar alguno de los cables de la pantalla.
    • Sostén tu iPhone firmemente y cierra el mango del iSclack para separar las ventosas, tirando del panel frontal hacia arriba desde la carcasa trasera.

    • El iSclack está diseñado para abrir tu iPhone lo suficiente para separar las piezas con seguridad, pero no lo suficiente para dañar alguno de los cables de la pantalla.

    • Despega las ventosas de tu iPhone.

    • Omite los siguientes tres pasos y continúa en el Paso 7.

    It's very difficult if you want to remove a cracked screen. The suction cup and Islack won't work. Does anybody know a better way?

    Herbert - Contestar

    I use Scotch Tape, shipping tape. Put a couple of layers over the crack screen. That seals it so you can use the suction cup to remove the front of phone.

    Michael Wallace -

    I used the plastic pry took and the spudger to open it up. I place the pry tool dead center below the home button and was able to put some pressure around the seam and the top popped up enough for me to get the spudger in there to hold it open and then work my way around with the plastic pry tool.

    johnoconna -

    Apply clear packaging tape to screen. Then suction cup to that.

    Tracey -

    Use clear nontextured tape place that over the phone screen. Refer to any guide that addresses replacing a shattered screen

    Abigail Cherry - Contestar

    I know it's tough with cracked glass. You just need enough to get in a plstic pry tool or guitar pick. Then you can pry it apart. Just be patient, I cannot stress that enough; the electronics are very, very small and fragile.

    Mike - Contestar

  4. Si no tienes un iSclack, usa una ventosa para separar el panel frontal:
    • Si no tienes un iSclack, usa una ventosa para separar el panel frontal:

    • Presiona la ventosa sobre la pantalla, justo arriba del botón de inicio.

    • Asegúrate de que la ventosa está presionada firmemente sobre la pantalla para tener un sellado hermético.

    Avec la ventouse, l’ouverture est brutale, tout s’est déclipsé d’un seul coup. Faire attention.

    Paul Briffaut - Contestar

    English Please!

    tom mozeleski -

    With the sucker, the opening is brutal, everything was cleared at once. Pay attention. (Paul’s comment translated by Google)

    Steve Schlotter - Contestar

  5. Mientras sostienes el iPhone hacia abajo con una mano, tire hacia arriba de la ventosa para separar ligeramente el conjunto del panel frontal de la caja trasera.
    • Mientras sostienes el iPhone hacia abajo con una mano, tire hacia arriba de la ventosa para separar ligeramente el conjunto del panel frontal de la caja trasera.

    • Tómate tu tiempo y aplica una fuerza firme y constante. El ensamblaje de la pantalla es mucho más ajustado que la mayoría de los dispositivos.

    • Con una herramienta de apertura de plástico, comienza a hacer palanca con cuidado hacia abajo la caja trasera, alejándola del conjunto de la pantalla, mientras continúas tirando hacia arriba con la ventosa.

    • Hay varios clips que unen el ensamblaje del panel frontal a la carcasa posterior, por lo que es posible que necesites usar una combinación de la ventosa y la herramienta de apertura de plástico para liberar el conjunto del panel frontal.

    Be extra careful here. If you don’t take your time, your front panel may jerk back on you, causing you to overextend and break the front camera/mic flex cable; happened to me. Slowly peel back the front panel, opening it no more than 90º.

    Thomas - Contestar

    watch out for the left side of the phone the adhesive bunches up around the inner clips, i didn’t realize it and the upper left of my screen cracked pretty bad. But this guide is awesome follow every direction to the letter

    Aaron Fitzpatrick - Contestar

  6. Tira de la protuberancia de plástico para liberar el sello de vacío en la ventosa. Retira la ventosa del ensamblaje de la pantalla.
    • Tira de la protuberancia de plástico para liberar el sello de vacío en la ventosa.

    • Retira la ventosa del ensamblaje de la pantalla.

  7. Tira del extremo del botón de inicio del ensamblaje del panel frontal para separarlo de la caja posterior, utilizando la parte superior del teléfono como una bisagra. Abre la pantalla en un ángulo de aproximadamente 90º y apoyala contra algo para mantenerla levantada mientras está trabajando con el teléfono. Agrega una banda de goma para mantener la pantalla de forma segura en su lugar mientras trabaja. Esto evita una tensión excesiva en los cables de la pantalla.
    • Tira del extremo del botón de inicio del ensamblaje del panel frontal para separarlo de la caja posterior, utilizando la parte superior del teléfono como una bisagra.

    • Abre la pantalla en un ángulo de aproximadamente 90º y apoyala contra algo para mantenerla levantada mientras está trabajando con el teléfono.

    • Agrega una banda de goma para mantener la pantalla de forma segura en su lugar mientras trabaja. Esto evita una tensión excesiva en los cables de la pantalla.

    • También, puede usar una lata de bebida sin abrir para sostener la pantalla.

    Be careful If we leave the screen connected and set it to 90 degrees, the speaker / sensor flex may break. With an opening of 60 degrees it is convenient to completely disconnect the screen. The headset's flex is short, and if we put it at 90º, it can break. Guiding me from the images of iFixit, I have broken two cables.

    Español:

    Cuidado. Si dejamos la pantalla conectada y lo ponemos a 90 grados, el flex del altavoz/sensor puede romperse. Con una abertura de 60 grados es conveniente desconectar enteramente la pantalla. El flex del auricular es corto, y si lo ponemos en 90º , se puede romper. Guiándome de las imágenes de iFixit, se me han roto dos cables.

    txaukos - Contestar

    At 60º the display will block access to all the screws and the phone would be practically unserviceable, so I’m having trouble making sense of this comment. The cables on a factory original display are pretty tough and designed with enough slack that a 90º angle is no problem. Same with any decent aftermarket display.

    Jeff Suovanen - Contestar

    If you look at the enlarged image, you can see how the flex cable from the camera / speaker is in tension. This is my opinion. Sorry for my bad English

    Si usted se fija en la imagen ampliada, puede ver cómo el flex cable de la cámara/altavoz está en tensión. Esta es mi opinión.

    Perdón por mi mal inglés

    txaukos - Contestar

  8. Varios clips a lo largo del borde superior del panel frontal forman una bisagra parcial, lo que permite que el conjunto del panel frontal se abra como un libro. Durante el montaje, alinee los clips justo debajo del borde superior de la carcasa trasera. A continuación, desliza el panel frontal hacia arriba hasta que su borde superior quede alineado con el de la carcasa posterior.
    • Varios clips a lo largo del borde superior del panel frontal forman una bisagra parcial, lo que permite que el conjunto del panel frontal se abra como un libro.

    • Durante el montaje, alinee los clips justo debajo del borde superior de la carcasa trasera. A continuación, desliza el panel frontal hacia arriba hasta que su borde superior quede alineado con el de la carcasa posterior.

    I would recommend protecting the screen once the display is free and the suction cup has been removed. This will help avoid any possibility of accidental scratching of the display crystal while the remaining steps are being performed. I used an inexpensive screen protector then removed it after reassembling and testing are complete.

    anthonyspampinato - Contestar

  9. Retira los siguientes tornillos Phillips del soporte del conector de la batería:
    • Retira los siguientes tornillos Phillips del soporte del conector de la batería:

    • Un tornillo de 2.3 mm

    • Un tornillo de 3.1 mm

    for the iPhone 6 Plus, all screws were Phillips #000

    Michael Adams - Contestar

    I had difficulty removing the 3.1mm (iPhone 6 Plus / Phillips #000); had to give it significant downward pressure to get it started.

    Allen Matheson - Contestar

    stripped the 2.3mm screw attempting to remove, had to use excessive force to successfully remove

    Matthew Gao - Contestar

    The Phillips bits provided in the kit would not engage the Phillips heads enough to loosen them. Luckily I had my own small screwdriver set that worked like a charm.

    David Davis - Contestar

    Same issue. Could not remove the screw. Dead in the water.

    Tiffany - Contestar

    Agree with above comments regarding the supplied Phillips bit. It is not the correct size.

    Use a Phillips #000.

    bobgottner - Contestar

    Phillips #000 is what’s included in the kit. As others mentioned above, firm downward pressure is key. The phone is not that delicate; just press hard and crank it.

    Jeff Suovanen -

    Is this step necessary ?\

    Asianay - Contestar

    @asianay0129 Yes, disconnecting the battery is necessary. You can sometimes get away with skipping it, at the risk of destroying something important and potentially bricking your phone. Not a wise gamble for the sake of skipping two screws.

    Jeff Suovanen - Contestar

  10. ¡Envío gratuito para todos los pedidos de más de USD100 o que contengan un Pro Tech Toolkit!

    Visita Nuestra Tienda
  11. Retira el soporte del conector de la batería de metal del iPhone.
    • Retira el soporte del conector de la batería de metal del iPhone.

    Was not able to remove the battery connector bracket as one of the cable connectors was glued/stuck to the underside. Instead moved the bracket out of the way to disconnect the battery. Care should be taken not to over bend/stretch the ribbon cable.

    dwtan - Contestar

    That may be just the foam connector adhering to the bracket. If you pull up gently and twist slightly it should separate.

    Evan Noronha -

    It was the foam connector, and it did twist free with a gentle pull

    Al Taylor - Contestar

  12. Uss una uña limpia o el borde de una herramienta de apertura para levantar suavemente el conector de la batería de su zócalo en la placa lógica
    • Uss una uña limpia o el borde de una herramienta de apertura para levantar suavemente el conector de la batería de su zócalo en la placa lógica

    • Ten cuidado de solo levantar el conector de la batería, y no el enchufe de la placa lógica. Si se levanta en el zócalo de la placa lógica, puedes romper el conector por completo.

    you may consider placing a thin non-conductive item between the connector and the socket like a bit of rubber band to prevent any power flowing during this procedure

    Michael Adams - Contestar

    It was too close to other parts to pry up with either end of plastic tool. Finally used 1 tine of tweezer to lift edge. Came free easily

    Al Taylor - Contestar

    J’ai pris une loupe pour bien observer l’endroit où placer l’outil.

    Paul Briffaut - Contestar

    Magnification is key for many tasks and this is certainly one.

    Kenneth Gilbert - Contestar

    I couldn’t use the iFixit blue opening tool to pry that battery connector. I used the top of the black spudger near the hole where the 3.1mm screw was in step 9-10 to easily pry it open!

    Alyssa Sayuki - Contestar

  13. Retira los siguientes tornillos Phillips que sujetan el soporte del cable del conjunto del panel frontal:
    • Retira los siguientes tornillos Phillips que sujetan el soporte del cable del conjunto del panel frontal:

    • Tres tornillos de 1.2 mm

    • Un tornillo de 1.5 mm

    • Un tornillo de 2.9 mm

    • No intentes insertar tornillos más largos en los orificios de tornillo marcados en rojo. Hacerlo puede provocar daños irreparables en la placa lógica.

    There's an other panel with one screw in the middle.........

    Herbert - Contestar

    I _love_ the color coding of screws. I know this is a little OCD, but it would be incredibly useful if there were an 8.5 X 11 you could print with indicated homes for where to drop items from each step of disassembly. That is, in the box for step 9, little colored circles for where to place each screw type. As long as you don't jostle the paper, it would make it a lot easier to know exactly where you are in reassembly.

    cscarlson47shop - Contestar

    I have done the exact same thing. Created a sheet where each screw goes.

    Chris Murphy -

    On my iPhone 6 plus, none of the screws listed in this step are removable with the Phillips 00 screwdriver! I got this far and now am stymied because I can't get these four screws out! Any other screwdrivers I should use?

    garth libhart - Contestar

    You are absolutely right, and you will strip the heads if you try very hard with the PH00. These screws are all PH000.

    oscar -

    I used the 000 bit from the ifixit 54 piece kit.

    hhandh - Contestar

    Actually you don’t need to do steps 12 to 18 if you attach the display panel to the iPhone box as shown in step 7 and handle your iPhone with care during the replacement. I didn’t disconnect the display panel mainly because the more you work on the interior of your phone the higher is the chance you break something.

    Dany Castillo - Contestar

    That's what I was thinking.

    The Wizard - Contestar

    I skipped this series of steps too. I was very careful when removing the battery and never had an issue with the screen leaning back against the box that this battery shipped in. I even broke half of the third strip of adhesive but used a plastic card to slide under the battery and it slowly lifted out without applying heat.

    mark - Contestar

    I'm having trouble with one screw not wanting to come out. Any suggestions to keep from stripping the head and getting it?

    Patric - Contestar

    which screws are which sizes cause i ordered new ones and cant figure it out

    MONsterHEIT - Contestar

    I also did not see the need to remove the display assembly for this repair. However I did place a can of corn against the vertically positioned display and then secured the display to the can with a rubber band.

    whiteshephard - Contestar

    I recommend removing the display assembly, I didn’t and somehow damaged the home button cable. At least remove the cover to ease the tension on the cables.

    Steve Schlotter - Contestar

    I played around with different screwdrivers to get certain screws out. I made sure I wasn’t applying heavy pressure so I wouldn’t strip the head. Apple is crazy for doing this to us lol.

    Anyways invest in a magnetized mat to organize your screws. It was really difficult to keep things organized and still, especially with these tiny screws…

    Jeffrey Robinos - Contestar

    what happens if i forgot to put the ribbon cable shield back on? the phone is now working but i forgot to put the shield back on and i am missing 2 screws. can i leave the shield off?

    Fred ticoman. - Contestar

    @ticoman12 It’ll work without the shield, but the connectors may pop out unexpectedly.

    Jeff Suovanen -

  14. Retira el soporte del cable del conjunto del panel frontal de la placa lógica.
    • Retira el soporte del cable del conjunto del panel frontal de la placa lógica.

  15. En los próximos cuatro pasos, ten cuidado de hacer palanca solo en los conectores del cable, y no en sus enchufes en la placa lógica. Mientras sigues apoyando el panel frontal, uss una uña o el borde de una herramienta de apertura para desconectar la cámara frontal y el conector del cable del altavoz del auricular.
    • En los próximos cuatro pasos, ten cuidado de hacer palanca solo en los conectores del cable, y no en sus enchufes en la placa lógica.

    • Mientras sigues apoyando el panel frontal, uss una uña o el borde de una herramienta de apertura para desconectar la cámara frontal y el conector del cable del altavoz del auricular.

    Why does the screen need to come off?

    Sterling Coffey (N0SSC) - Contestar

    Because the cables are delicate, and following steps are easier if phone halves are not flopping around together, especially for amateurs.

    Matthew Goheen - Contestar

  16. Desconecta el conector del cable del botón de inicio. Desconecta el conector del cable del botón de inicio.
    • Desconecta el conector del cable del botón de inicio.

  17. Asegúrate de que la batería esté desconectada antes de desconectar o volver a conectar el cable en este paso. Usa una herramienta de apertura de plástico para desconectar el conector del cable de datos de la pantalla. Al volver a armar su teléfono, el cable de datos de la pantalla puede salirse del conector.
    • Asegúrate de que la batería esté desconectada antes de desconectar o volver a conectar el cable en este paso.

    • Usa una herramienta de apertura de plástico para desconectar el conector del cable de datos de la pantalla. Al volver a armar su teléfono, el cable de datos de la pantalla puede salirse del conector.

    • Esto puede ocasionar líneas blancas o una pantalla en blanco al volver a encender su teléfono. Si eso sucede, simplemente vuelve a conectar el cable y enciende su teléfono. La mejor manera de encender y apagar tu teléfono es desconectar y volver a conectar el conector de la batería.

    The piece of advice about power cycling the phone by disconnecting and reconnecting the battery proved crucial to the success of my repair (camera and lens replacement). At first when charging the phone after closing it, I got a dark, blank screen with an intermittent buzzing noise. After re-opening the phone and making sure all cables had been properly reconnected, I ignored the advice to power cycle the phone. Still all I got was a dark, blank screen (and intermittent buzzing if charging t). Then I opened it a third time (leaving the screen connected and attached at a 90 degree angle) and I only disconnected and reconnected the battery. Voila! When I closed the phone and powered it up, I got the screen to light up!

    Gianni - Contestar

    how did you disconnect and reconnect the battery?

    Teresa Trevino - Contestar

    If you’ve been following the guide, you already disconnected it in this step. To reconnect it, just line up the connector and press it into place.

    Jeff Suovanen -

  18. Finalmente, desconects el conector del cable del digitalizador. Al volver a conectar el cable del digitalizador, no presiones el centro del conector. Presiona un extremo del conector, luego presiona el extremo opuesto. Presionar en el centro del conector puede doblar el componente y causar daños al digitalizador.
    • Finalmente, desconects el conector del cable del digitalizador.

    • Al volver a conectar el cable del digitalizador, no presiones el centro del conector. Presiona un extremo del conector, luego presiona el extremo opuesto. Presionar en el centro del conector puede doblar el componente y causar daños al digitalizador.

    some images and guidance regarding reassembly would be helpful. You don't need to use the spudger to get them back on: fingers are better because there's a really subtle click you feel when you get them seated properly.

    cscarlson47shop - Contestar

    When you're reassembling, a note that this is the step where you should test for proper screen function would be really useful. First time I reassembled, I didn't seat something properly, got all the screws back together and then realized the screen wasn't functioning properly. Had to disassemble back down to step 14 and then re-reassemble.

    cscarlson47shop - Contestar

    I am having this issues right now! I have unplugged and plugged in these cables at least 20 times and each time I get white lines. I finally have it to where there are only 4 white lines and I am almost willing to live with it. Any suggestions?

    mattmay002 -

    Clean the screen connectors incase they are not making a clean connection

    Karen Jones - Contestar

    I'm having nightmares with the digitizer connector. Simply can't get it to work unless I'm applying some pressure on the connectors. Everything seems almost microscopically clean. Any suggestions friends?

    Henry A -

    could it be the replacement screen? test with your old screen and see if you have the same problem.

    ChiangFeng - Contestar

    To ++mattmay002++  Did you power cycle the phone? Check out the comments on the previous step for a how to.

    Robert Liles - Contestar

    I had issues with it too. When connecting this cable, make sure to rock finger side to side after connecting. It’s a wide connector so try to listen for 2 clicks on this one connector. That’s how I fixed mine

    Albert Einstein - Contestar

    Re-attaching this cable is the only tricky part to replacing the battery on my 6+. It had a bow on the middle that I had to flatten out before pressing the connector on with finger first on one edge and then on the other. I had white tire tracks on the screen and no touch screen until I connected it correctly. The front has to rest in just the right place on the back while attaching this thing so the cables aren’t strained the front doesn’t fall down. Small fingers would be a plus at this step.

    richard - Contestar

    Reseating these connectors on reassembly is definitely the most difficult part of this repair. It took me several attempts before the lowermost connector would seat properly and I did accidentally bend it slightly in the process. Fortunately I was able to get it straight again and get it to click in. The other three went in fine though and no lasting damage seems to have been done.

    Andy Gibbons - Contestar

    Another thing - These cables can become overlapped in the wrong way and make you think they are in a different order than they should be. Eg. it’s easy to mix up the ones from step 15 and 17. You can actually unravel the cables and re-layer them on top of each other in any order, so remember this! They look like they’re one solid mass but they’re not.

    domarius - Contestar

  19. Retira el conjunto del panel frontal de la caja trasera.
    • Retira el conjunto del panel frontal de la caja trasera.

    Never remove the screen without disconnecting the battery. It's possible the back light can be blown and that's a even more difficult repair. Always, ALWAYS, disconnect battery before repairing items. (Unless it's not possible.)

    Marvin Ballard - Contestar

    How do you disconnect the battery from the screen?

    Shamil Bhatti -

    The Step 11 disconnects the battery :)

    jeffxtechs - Contestar

    I think you mean Step 8 :)

    Jeff Suovanen -

    How do you disconnect the battery

    I tried it once and

    Brian - Contestar

    And what? I tried it once and here’s a million dollars?

    Oh I get it… they got him! :(

    https://www.youtube.com/watch?v=UlznqpBg...

    domarius -

    When disassembling the iphone at this point note the cables, and there placement/orientation.

    GERARD SZAREK - Contestar

  20. Retira los dos tornillos Phillips de 1,8 mm que sujetan el soporte del botón de inicio al panel frontal.
    • Retira los dos tornillos Phillips de 1,8 mm que sujetan el soporte del botón de inicio al panel frontal.

    This guide is pointless, iPhone 6/6 plus home button is not replaceable, period.

    Tom Chai - Contestar

    Yes it is absolutely replaceable. You need to remember it is a encrypted security feature, so you'll need the apple ID or password to regain control again if replaced. That's the whole point to secure your data.

    Mike -

    Yes, the iPhone 6 and 6 Plus home buttons are replaceable. I do several replacements for customers and they work just fine with one exception. The fingerprint reader around the home button does not work after replacing the home button

    BrentTaylorBA - Contestar

    Hi Brent, I have a iPhone 6 plus with a shattered screen to repair and the home button is gone. You have said that you've been able to replace the home buttons successfully. I was wondering how you got past the error 53 problem when restoring it? Any suggestions or help would be greatly appreciated.

    arcadian212 -

    Error 53 was resolved by Apple with an iOS update, so fortunately this is no longer an issue! As others have stated, it's perfectly possible to replace the home button, but you will lose fingerprint sensor functionality (the original sensor is paired to your iPhone's logic board at the factory, and only Apple can pair a new one).

    Jeff Suovanen -

    Why does that make it pointless? The guide is geared towards screen replacement, with the intent of using the original home button and a new screen. It clearly states this. What about this guide is pointless? It's actually very helpful.

    abyss478 - Contestar

    Warning: The iphone 6 will brick after a restore if the home button is replaced. I agree with the other commenters that it is not a replaceable part because of this issue. If you try to restore the iPhone 6 after replacing the home button it will get stuck in recovery mode and give error 53 when a restore is attempted. I learned this the hard way! Please be careful and don't restore your phone if you do this repair.

    max - Contestar

    What did you do after your phone got stuck in recovery mode ?

    Lynn -

    I had an error 53 when trying to restore a iphone 6 plus.

    I bought a new heat shield with flex ribbon attached and installing that allowed me to get a restore complete.

    steve - Contestar

    I couldn't get my fingerprint reader to work after following this guide. I ended up taking the phone back apart and replacing the new screens' backing plate and the attached home button cable with the old, original one and now the fingerprint sensor works!

    fsharp320 - Contestar

    The little square rubber gaskets that cloak the mounting holes (little square nubs at the bottom of the picture in Step 19) for the Pentalobe Screws in Step 1 above had a tendency to fall off the screen. Further, if replacing the screen, these should also accompany the other items transferred to the new screen. This is just a small oversight I have seen from this repair guide, otherwise, smooth as silk.

    Justin - Contestar

    The connector seemed a bit raised after re-assembling, I noticed after pressing the bracket down on in preparation for screwing in. I don’t know if it’s normal for it to have a slightly raised feeling but it was noticeable. Enough to make me wonder if it’s too much pressure on it once it’s screwed together.

    domarius - Contestar

  21. Retira el soporte del botón de inicio del ensamblaje del panel frontal.
    • Retira el soporte del botón de inicio del ensamblaje del panel frontal.

    buen día, cuando no me reconoce el touch id pero el boton si hace la función de botón ejemplo si me envía a home pero no reconoce el alcance fácil dos toques no reconoce el lector biométrico

    Yamir Maximino - Contestar

  22. Usa la punta de un spudger* para remover el conector del botón de inicio de su zócalo.                                                                        *herramienta antiestática con un extremos en punta y otro plano Usa la punta de un spudger* para remover el conector del botón de inicio de su zócalo.                                                                        *herramienta antiestática con un extremos en punta y otro plano
    • Usa la punta de un spudger* para remover el conector del botón de inicio de su zócalo. *herramienta antiestática con un extremos en punta y otro plano

    Will disabling and removing fingerprint passcode thru settings software wise prior to repair or starting the replacement, will this feature with a new replacement home button resolve the error 53 or the repairer need to use the original home button sensor with the correct fingerprint stored in the tiny small chip ? I have replaced a gsm iPhone 6S not plus screen making sure that not to tear off the sensor chip successfully repaired. -Joan

    JOAN E. VERGARA - Contestar

    Hi Joan! If I am understanding your question correctly, disabling the fingerprint passcode prior to repair WILL NOT result in Touch ID working after the repair. You should look at Jeff Suovanen's comment at the bottom, as he explains the two ways to keep Touch ID working. In order to keep Touch ID working, you will need to find a logic board that is paired with the home button and replace both of those components.

    Scott Havard -

    • Coloca cuidadosamente la punta del spudger debajo del cable conector del botón de inicio.

    • Mueve suavemente el spudger y separe el cable del conector del botón de inicio del adhesivo que lo sujeta al panel frontal.

    • Si el cable no se separa fácilmente, aplica calor utilizando el iOpener o un secador de cabello para ablandar el adhesivo. Vuelve a intentar separarlo teniendo cuidado para no dañar el cable.

    Es necesario calentar para que se desprenda de una forma comoda

    Yamir Maximino - Contestar

    i found using a needle works well too, as the fine point of the needle will be able to get under the adhesive and i can gently separate it.

    ChiangFeng - Contestar

    heat thoroughly with a hair dryer. (away from your work area so you don't blast your parts all over the place!) pops right off.

    edwardlyman - Contestar

  23. Con la punta del dedo, presiona suavemente, pero no quites, el botón de inicio hacia arriba desde el lado opuesto para liberar un borde de la junta del botón de inicio del panel frontal. No presiones el botón de inicio hasta el final, solo necesitas obtener una esquina libre, de modo que puedas soltarla con un spudger.
    • Con la punta del dedo, presiona suavemente, pero no quites, el botón de inicio hacia arriba desde el lado opuesto para liberar un borde de la junta del botón de inicio del panel frontal.

    • No presiones el botón de inicio hasta el final, solo necesitas obtener una esquina libre, de modo que puedas soltarla con un spudger.

    • La junta de goma que rodea el botón de inicio es muy delgada. Para evitar que la junta se rompa, recomendamos aplicar una cantidad mínima de calor.

  24. Desliza con cuidado la punta de un spudger debajo del perímetro del botón de inicio para separarlo del ensamblaje del panel frontal. Desliza con cuidado la punta de un spudger debajo del perímetro del botón de inicio para separarlo del ensamblaje del panel frontal.
    • Desliza con cuidado la punta de un spudger debajo del perímetro del botón de inicio para separarlo del ensamblaje del panel frontal.

    The little rubber gasket seems to be a moisture seal. It isn’t glued down but over time it seals itself to the display. Pushing the spudger around underneath simply breaks the bond between the two surfaces. Be sure to do it carefully so as not to tear it.

    bichmgnt - Contestar

  25. Levanta y remueve el ensamblaje del botón de inicio del ensamblaje del panel frontal.
    • Levanta y remueve el ensamblaje del botón de inicio del ensamblaje del panel frontal.

    So this fix is hardware only? Do I need to disable the touch ID feature before removal and wWhat do I do next to get the touch ID feature to function?

    Dasteufelhund - Contestar

    After removing the home button, remove the two black rubber bumpers from the ‘Pentalobe Screw’ mount brackets and transfer them to the new screen, this helps secure the home button in place and screw tension.

    James_P - Contestar

Conclusión

Para volver a ensamblar tu dispositivo, sigue estas instrucciones en orden inverso.

91 personas más completaron esta guía.

Un agradecimiento especial a estos traductores:

83%

Estos traductores nos están ayudando a reparar el mundo! ¿Quieres contribuir?
Empezar a traducir ›

My iphone was screen broken and i change it with a original complete iphone screen, the home button works fine but the touch id dont work. I change the home button to the one that i have in the broken screen and still the touch id dont work. What can i do to fix the touch id?

Juanjo Checo - Contestar

replace the flex cable which connects touch ID cable with mother board

engradnanriaz -

Hi guys, I replaced my front assembly and I'm having the opposite issue with my home button: The TouchID is working fine, but the home button being pressed is not working. I've tried re-seating the cable a few times. I'm normally pretty good at these kinds of things but I'm assuming I may have somehow crimped one of the ribbon cables.

My question: If something is damaged, is it more likely the cable on the back of the heat-sink that is damaged, or the home button ribbon cable itself? I realize that I will lose TouchID if its the latter, I just want to know what my options are. I'm having trouble searching the issue because everyone else has the issue where the TouchID doesn't work (for obvious reasons) but mine is working just fine.

Thanks for any advice.

Joshua Ryan - Contestar

Hi everyone, I replaced the home button on my cell phone iphone 6+, the home button functionality works just fine, however the biometrics fingerprint reader does not work anymore. Any suggestions? Thank you

J Jesus Perez - Contestar

Unfortunately, as stated in the introduction to this guide, that outcome is normal. For security reasons, the fingerprint sensor is coded to your phone's logic board at the factory. If you replace the button, you'll lose the fingerprint sensor function. Only Apple has the capability to pair new Touch ID sensors to existing phones. As far as I know, there are only two ways around this: (1) replace both your home button and logic board with a factory-paired home button and logic board harvested from another phone, or (2) pay Apple for an out-of-warranty repair (meaning you ship your phone to them and they give you a refurb in return).

Jeff Suovanen -

Hi guys, I replaced my front assemblyHi guys, an I'm having an issue with my home button: The TouchID is working fine, but the home button being pressed is not working. Why??What happens?I've just checked all connections and cables are ok...thanks so much.

tiagoenascimento - Contestar

I am using 6 plus my phone home button heats always and drains the battery .Touch Id shows "Failed to set up Touch ID".I do know what to do. Please help me.............

Karankumar Kk - Contestar

Where RUS language?

Michael JaNuaRy - Contestar

Hello my name is ammy I am from India my question is I have a iPhone 6 Plus some kind of reason I am change iPhone screen and home button after that my scanner doesn't work .Give me some suggestions

ambrish singh - Contestar

Hello Ambrish,

Unfortunately replacing the home button on the iPhone 6 Plus renders the Touch ID functionality useless. Jeff Suovanen replied with an excellent answer on this topic a couple of comments above this one.

Scott Havard -

what happens if you loosen the home button socket as a result of trying to disconnect the Home button? My Touch ID doesn't work and I noticed the the home button socket is very loose now. Is that a reason why it isn't working?

Dipesh - Contestar

Is there a way to test the Home Button to confirm that is in fact faulty?

Sam Crismon - Contestar

muito bom esse ifixit estou amando parabéns

ncesar133 - Contestar

i changed my home button it functions well but when i connect my iPhone to charger, home button stops working!!

When i remove the lighting cable it again starts working normally. What can be the issue??

Rishabh Madaan - Contestar

HI @rishabh_ this is actually a common issue! Charging can often interfere with the Touch ID’s sensors. Be sure you’re using an authentic Apple charging cable!

Sam Lionheart -

Thank you @Sam Lionheart for you reply:)

Actually in my case there was i think an electornic interfarence between my touch id metal tray support and lightning connector’s metal (which is on the top of it). I seprated them with a thin rubber gasket layer and it started working fine without any interfarence even on charging:)

Btw thank you once again for your concern :)

Rishabh Madaan -

Oh interesting! Thanks so much for sharing your issue and solution! Great job on your fix =)

Sam Lionheart -

Agregar Comentario

Ver Estadísticas:

Ultimas 24 Horas: 25

Últimos 7 Días: 160

Últimos 30 Días: 796

Todo El Tiempo: 118,199