Saltar al contenido principal

Introducción

Aprende como reemplazar la pantalla de tu iPhone 7. "Esta guía esta pensada para ser usada con repuestos completos de pantalla"

Esta parte debería venir con el ensambaje frontal, altavoz de llamadas y escudo EMI ya instalado, para que la reparación sea más fácil.

Todo lo que tienes que haces es quitar la pantalla antigua y transferir el botón a la nueva para que Touch ID funcione.

Utiliza esta guía si tu nueva pantalla viene con la altavoz auricular, ensamblaje de cámara frontal, y placa de escudo de LCD ya está instalado. Simplemente quita la pantalla antigua y transfiere el botón de inicio / Touch ID en la nueva pantalla.

Si tu pantalla de reemplazo no incluye esos componentes, sigue esta guía más detallada en su lugar.

En cualquier caso, el sensor original de inicio / Touch ID debe transferirse a la nueva pantalla para que Touch ID funcione.

Resumen del Video

  1. Antes de comenzar, descarga la batería de tu iPhone por debajo del 25%. Una batería de iones de litio cargada puede incendiarse y / o explotar si se perfora accidentalmente.
    • Antes de comenzar, descarga la batería de tu iPhone por debajo del 25%. Una batería de iones de litio cargada puede incendiarse y / o explotar si se perfora accidentalmente.

    • Apaga tu iPhone antes de comenzar el desmontaje.

    • Remueve los dos tornillos pentalobe de 3.4 mm en el borde inferior del iPhone.

    • Abrir la pantalla del iPhone dañará sus sellos impermeables. Ten sellos de reemplazo listos antes de seguir con el próximo paso o ten cuidado de evitar la entrada de líquidos si vuelves a ensamblar tu iPhone sin reemplazar los sellos.

    Can anyone confirm 7/7P's pentalobe screws have a ring of seal near the screw head?

    Cooper Chase - Contestar

    Confirmed, the screws have a black ring seal around the head.

    rcheing - Contestar

    Can’t get the display front

    Bernadette Pfeifer - Contestar

  2. Si el cristal de la pantalla está agrietado, mantén unidos los trozos y evita lesiones corporales durante la reparación poniendo  cinta adhesiva sobre el cristal. Coloca cintas  superpuestas sobre la pantalla del iPhone hasta cubrir toda la cara. Esto mantendrá los fragmentos de vidrio contenidos y proporcionará integridad estructural al hacer palanca y levantar la pantalla.
    • Si el cristal de la pantalla está agrietado, mantén unidos los trozos y evita lesiones corporales durante la reparación poniendo cinta adhesiva sobre el cristal.

    • Coloca cintas superpuestas sobre la pantalla del iPhone hasta cubrir toda la cara.

    • Esto mantendrá los fragmentos de vidrio contenidos y proporcionará integridad estructural al hacer palanca y levantar la pantalla.

    • Usa gafas de seguridad para proteger sus ojos de cualquier vidrio que pueda saltar durante la reparación.

    • Si el vidrio roto dificulta la colocación de una ventosa en los siguientes pasos, intenta doblar un trozo fuerte de cinta (como cinta adhesiva para ducto)en una esquina y levanta la pantalla con eso.

    In case of broken glass you can make the suction cup much more effective by covering the glass with a broad piece of translucent tape which eliminate air leakage through cracks in the glass.

    lionno1 - Contestar

    Il n’est pas nécessaire de mettre beaucoup de scotch.

    Au contraire plus vous mettez de scotch, plus il y aura de défauts et la ventouse ne collera pas.

    Une bande bien positionnée suffit.

    Chloé Bossuette - Contestar

    I’ve used hot glue on low setting to remove all types of crystals. The hot glue will release with a little iso alcohol. No damage to glass or plastic faced crystals or screens. Use a narrow piece of wood as a prying handle.

    Emilio Gonzalez - Contestar

    I recently had issues with removing the glass with the suction cup. I have done this many times with older generation iPhones but this time the glass seemed sealed on quite solidly. I told myself that the last option would be to use the screwdriver tip. After all my attempts, I transitioned to the option of using the screwdriver tip. Surprisingly, it was the easiest thing ever. I placed the 1mm flathead screwdriver at the interface between the glass and the cover (normal start location) and pried up very gently. Voila, the glass came up and I can’t even notice any dents or scratches. It felt much easier than the suction cup technique. If the suction cup is giving you a hard time consider using that 1mm flathead.

    forhereyesonly - Contestar

  3. Calentar el borde inferior del iPhone ayudará a suavizar el adhesivo que asegura la pantalla, facilitando su apertura.
    • Calentar el borde inferior del iPhone ayudará a suavizar el adhesivo que asegura la pantalla, facilitando su apertura.

    • Utiliza una pistola de calor o preparar un iOpener y aplicarlo en el borde inferior del iPhone durante un minuto para suavizar el adhesivo debajo.

    ¿Cuántos segundos son los recomendados?

    joscarlos91 - Contestar

    Sesenta segundos

    Krutav Shah -

    It is a process. I heated the lower area of the phone with a hair dryer on and off (1min each) about 3-4 times before I was able to get the provided tool in.

    Dan - Contestar

    I suggest using a hairdryer. I used the iOpener for maybe 30 mins to no avail. However, when I used the hairdryer the screen came of much quicker.

    Michael - Contestar

    I totally Mr. Myagi’ed it, by rubbing my hands together until they burned, then held the phone un my hot hands. I did this 5-6 times over a couple of minutes. It was a good zen way to get started!

    Ark - Contestar

    Can a heat gun be used?

    Lee - Contestar

    Absolutely. Just don’t overdo it—the adhesive usually softens up pretty easily. If you are experienced with a heat gun, you’ll have no problem. (If you are inexperienced, it’s easy to cook the display or cause other damage.)

    Jeff Suovanen -

    If i use this process, will iphone 7 still be sealed, water/ splash resist after that?

    Marius Serban - Contestar

    Opening the iPhone's display will compromise its waterproof seals. Have replacement seals ready before you proceed past this step, or take care to avoid liquid exposure if you reassemble your iPhone without replacing the seals.

    Angel Hermida -

    Can I use a cpb heating pad to soften the adhesive ? If yes how much time and temperature ?

    davidecongiu - Contestar

    Will doing this compromise the screen protector (Zagg) that I have on my phone?

    Eric Nance - Contestar

    Hairdryer worked for me but I needed to use a razor to pry it open at the bottom then used the spudger

    Gina Torres - Contestar

  4. Conecta una ventosa a la mitad inferior del conjunto de la pantalla, justo por encima del botón de inicio. Asegúrate de que la ventosa no se coloque sobre el botón de inicio, ya que esto evitará que se forme un sello entre la ventosa y el vidrio frontal.
    • Conecta una ventosa a la mitad inferior del conjunto de la pantalla, justo por encima del botón de inicio.

    • Asegúrate de que la ventosa no se coloque sobre el botón de inicio, ya que esto evitará que se forme un sello entre la ventosa y el vidrio frontal.

    The glass is completely cracked and the suction cup doesn't work because it gets air in between. any tip?

    Display is glued and doesn't come off.

    support - Contestar

    A wide, single strip of packing tape, well placed, will solve this for you. :)

    Mimic44444 - Contestar

    Last comment works well. Thank you !

    Using packing tape for a cracked screen should be included in the description in Step 3.

    Cracked screen is most probably the reason you are replacing it.

    Arni Benediktsson - Contestar

    I agree that using packing tape for a cracked screen should be included in this steps description. I don’t have wide but turned mine horizontal and that worked great.

    Mary Knapp - Contestar

    Bekomme die Oberschale einfach nicht runter! Trotz mehrmaligem erwärmen durch den iOpener und seitlichen bewegen! Weiß nicht mehr weiter!

    Stephan Lienhard - Contestar

    Wouldn’t that screw up the Touch ID?

    Rexx Havok - Contestar

  5. Tira hacia arriba de la ventosa para crear un pequeño espacio entre el ensamblaje de pantalla y la caja trasera. Inserta el extremo plano de un spudger en el hueco. El adhesivo  que sostiene la pantalla en su lugar es muy fuerte, y la creación de esta separación inicial requiere una cantidad significativa de fuerza. Si te resulta difícil crear una abertura, oscila la pantalla hacia arriba y abajo para debilitar el pegamento hasta que puedas insertar el  spudger.
    • Tira hacia arriba de la ventosa para crear un pequeño espacio entre el ensamblaje de pantalla y la caja trasera.

    • Inserta el extremo plano de un spudger en el hueco.

    • El adhesivo que sostiene la pantalla en su lugar es muy fuerte, y la creación de esta separación inicial requiere una cantidad significativa de fuerza. Si te resulta difícil crear una abertura, oscila la pantalla hacia arriba y abajo para debilitar el pegamento hasta que puedas insertar el spudger.

    This was SO hard for me to do with the spudger. I couldn’t get a gap to insert it because my phone was so cracked (even though I used tape on the front) to get a solid seal with the suction cup. I ended up taking a VERY thin knife and inserting it straight down to make the initial break that allowed me to insert the spudger.

    jessica harlow - Contestar

    I’ve given up using a plastic spudger to try to open any of these phones. I use a metal one with a flat base and a very sharp end…close to a razor. As long as I’m careful, it won’t slip and scratch the base. It’s much easier than using these plastic spudgers.

    mcr4u2 -

    I confirm that the plastic spudger it’s not the best tool for this operation. I suggest to use a larger metal tool like a “Jimmy” or “iSesamo open tool” (I used the first one)

    Cristef -

    Im trying to get the screen off right now and my phone is not cracked and its still a pain

    Jordon Johnson - Contestar

    Using a blow dryer was extremely helpful and using the suction cup towards one of the lower edges was also helpful

    Jordon Johnson - Contestar

    This is not working for me. How long does the heat need to be applied? Still trying right now…. =/

    Chris Gallego - Contestar

    Apply hair dryer for at least 1 minute. I inserted the tip end of a thin mini screwdriver and with some force, pryed it open and inserted my plastic spudger to continue the separation process. It worked, just be patient.

    Please wear protective glasses! My iPhone glass was severely cracked, when separating the glass a corner area of broken glass exploded in my face. Apply transparent tape over the broken glass to contain the shards.

    amberron - Contestar

    I second Jessica’s January 8 comment.  I just finished a battery replacement on my iPhone 7 and this step was the most nerve-wracking part.  I ended up using a sharper (but not razor-sharp) metal object to get this done with confidence (tried the spudger and guitar pick but not thin enough).  The tool I used was the exact duplicate of what iFixIt calls “iSesamo Opening Tool” in their tool selection.  I did the heat up with a hair dryer (after attempts with an iOpener hot pad) and the secret (as Jessica also noted)  was to not use the angle of attack shown in the pictures, but to push it in more vertically along the bottom edge while pulling up on the suction cup.  From there you can easily lever the tool to the lower angle-of-attack (as shown in the picture).  I actually used the metal tool for most of the perimeter as well, just don’t go deep (you don’t need to).  Notes: my display was intact, and I was able to pull up fairly hard with a glass screen protector still on it.

    Ted - Contestar

    This is frustrating. I heated the lower edge with a hair dryer for 1 min on high about 3-4 times. In between each heat cycle, I rocked the suction cup back and forth. I was eventually able to create significant space for the provided tool. This takes a lot of patience. Once the space was created, it was very easy to remove the screen.

    Dan - Contestar

    use a fingernail, then the blue tool, then the spudger

    Therese Peffer - Contestar

    The iOpener worked just fine for me. Had to keep it on for a few minutes. I also was able to get the suction cup seal right close to the edge, over top of the home button for added leverage. Used the blue tool and transitioned to the spudger. Slow, steady pressure…and patience. ;)

    johnhall918 - Contestar

    Unable to open an iPhone 7 display assembly. Used gell pack at 150 degrees F. The phone wouldn’t budge when I used the iFixit suction cut. Part of the problem is that the cup doesn’t adhere for long before it looses suction. I suspect it would work better on unbroken glass, but that doesn’t help me now. After spending a lot of time at this, I changed heating methods to a hot air heater. I raised the temp of the bottom end of the phone to, ultimately, 175 degrees, and used a variety of tools to try to pry the glass apart enough to get a spudger (or anything) in, but it didn’t even lift enough for a double-edged razor blade to get in. I’ve been trying this for hours now, and about to give up and throw a lot more money at this to have a service perform the work. I figured that 175 was as high as I should need to go to soften the adhesive without damaging the electronics. Should I have gone higher? I see no mention of measured temps in any instructions or comments.

    ted - Contestar

    Have you tried applying tape to the broken screen? This will help a lot with keeping the suction cup on it.

    Christian Groothuis -

    It doesn’t need to get very hot; pulling up on the display is mainly what does the trick. Make sure the two pentalobe screws have been removed and then try the tricks in this step. If all else fails, superglue the suction cup to your display and let it cure, and then pull. Keep in mind you only need a tiny gap to insert a plastic pick and start cutting the adhesive. Good luck!

    Jeff Suovanen -

    Just a question. After this operation the impermeability function was compromitted?

    bentek86 - Contestar

    The trick I found, was to add packing tape right across the bottom over the home button then use hairdryer on the end, then suction cup on the very bottom and it lifted enough to get a gap. No one mentioned how it would be impossible to handle the phone after the hairdryer ;)

    Andrew Lansdowne - Contestar

    Didn’t have an iOpener and 60 seconds on a hairdryer wasn’t doing it for me. Still wouldn’t budge. I had to take a very sharp razor along the seam at the bottom between the speakers. It took about 20 passes for it to separate enough to get the spudger in. Make sure you keep the razor at a 90-45˚ angle and that it goes no more than 1-2mm into the phone. The bottom of the phone is metal, but the casing for the screen is plastic. So if you cut lower than a 45˚ (flat with the phone) you risk cutting into the casing. Apply light pressure when making the passes. I would just do the razor on the flat part on the bottom.

    minimalist - Contestar

    I used a hair drier while lifting up at the same time until I could get the too inside. The seal is pretty finicky. Just take your time and you should be fine. Work the hair drier and the tool all the way around before lifting the screen up and off. There will likely be sealant stuck between the screen and phone. You can just break it with the tool.

    Ray Bieze - Contestar

  6. Desliza el spudger a la izquierda a lo largo del borde inferior del iPhone. Gira el spudger para ampliar el espacio entre la pantalla y la carcasa trasera. Gira el spudger para ampliar el espacio entre la pantalla y la carcasa trasera.
    • Desliza el spudger a la izquierda a lo largo del borde inferior del iPhone.

    • Gira el spudger para ampliar el espacio entre la pantalla y la carcasa trasera.

    Didn’t have an iOpener and 60 seconds on a hairdryer wasn’t doing it for me. Still wouldn’t budge. I had to take a very sharp razor along the seam at the bottom between the speakers. It took about 20 passes for it to separate enough to get the spudger in. Make sure you keep the razor at a 90-45˚ angle and that it goes no more than 1-2mm into the phone. The bottom of the phone is metal, but the casing for the screen is plastic. So if you cut lower than a 45˚ (flat with the phone) you risk cutting into the casing. Apply light pressure when making the passes. I would just do the razor on the flat part on the bottom.

    minimalist - Contestar

    I used a hairdryer and a razor

    Gina Torres - Contestar

  7. Desliza el spudger por el lado izquierdo del iPhone, comenzando en el borde inferior y deslizando hacia los botones de control de volumen y el interruptor de silencio. No hagas palanca en el borde superior del teléfono, corres el riesgo de dañar los clips de plástico que sujetan la pantalla. No hagas palanca en el borde superior del teléfono, corres el riesgo de dañar los clips de plástico que sujetan la pantalla.
    • Desliza el spudger por el lado izquierdo del iPhone, comenzando en el borde inferior y deslizando hacia los botones de control de volumen y el interruptor de silencio.

    • No hagas palanca en el borde superior del teléfono, corres el riesgo de dañar los clips de plástico que sujetan la pantalla.

    Be VERY careful on this next step going up the right side of the phone. There is a ribbon cable 1/3 of the way up from the bottom that is very close to the edge. Do NOT use the blue triangle!!!! Just lightly rotate the spudger to get separation on the edge.

    Timothy Varvais - Contestar

  8. Inserta el borde plano de un spudger en la esquina inferior derecha del dispositivo. Gira el spudger para ampliar el espacio entre el ensamblaje de la pantalla y la caja trasera. Desliza el extremo plano del spudger por el lado derecho del teléfono para romper el adhesivo que sostiene la pantalla en su lugar.
    • Inserta el borde plano de un spudger en la esquina inferior derecha del dispositivo.

    • Gira el spudger para ampliar el espacio entre el ensamblaje de la pantalla y la caja trasera.

    • Desliza el extremo plano del spudger por el lado derecho del teléfono para romper el adhesivo que sostiene la pantalla en su lugar.

  9. Levanta la ventosa para levantar la pantalla y abra el iPhone. No levantar la pantalla más de 10º ya que hay cables planos  a lo largo del borde derecho del dispositivo que conecta la pantalla con la placa lógica.
    • Levanta la ventosa para levantar la pantalla y abra el iPhone.

    • No levantar la pantalla más de 10º ya que hay cables planos a lo largo del borde derecho del dispositivo que conecta la pantalla con la placa lógica.

    do not pull up pull sideways it will brake

    Riley Patterson - Contestar

    Made this mistake

    rachael.grime - Contestar

    Somehow my phone turned itself back on during the opening. Scared me a little, like a patient coming out of anesthesia during the operation. I was able to turn it back off. Gotta be more careful where you grab this thing.

    Bryant Larsen - Contestar

  10. Tira hacia arriba de la pequeña protuberancia en la ventosa para sacarla del panel frontal.
    • Tira hacia arriba de la pequeña protuberancia en la ventosa para sacarla del panel frontal.

  11. Desliza una púa de apertura a lo largo del borde superior del iPhone, entre la caja trasera y el panel frontal, para romper el adhesivo restante que sujeta la pantalla en su lugar. Ten cuidado de no dañar los clips de plástico en el borde superior del teléfono.
    • Desliza una púa de apertura a lo largo del borde superior del iPhone, entre la caja trasera y el panel frontal, para romper el adhesivo restante que sujeta la pantalla en su lugar.

    • Ten cuidado de no dañar los clips de plástico en el borde superior del teléfono.

    The plastic clips mentioned are on the top of the screen being replaced… so not sure why it matters not to break them. Trick here was to pull the screen downwards to open a gap at the top and then insert as shown and raise to break the seal.

    Andrew Lansdowne - Contestar

    This is relevant for other guides than the display replacement guide.

    jvalaamo -

  12. Tira del ensamblaje de la pantalla ligeramente hacia afuera desde el borde superior del teléfono para desenganchar los clips que lo sujetan a la caja posterior. Abre el iPhone moviendo la pantalla hacia arriba desde el lado izquierdo, como la tapa posterior de un libro. No intentes separar por completo la pantalla todavía, ya que hay varios cables frágiles que aún la conectan a la placa lógica del iPhone.
    • Tira del ensamblaje de la pantalla ligeramente hacia afuera desde el borde superior del teléfono para desenganchar los clips que lo sujetan a la caja posterior.

    • Abre el iPhone moviendo la pantalla hacia arriba desde el lado izquierdo, como la tapa posterior de un libro.

    • No intentes separar por completo la pantalla todavía, ya que hay varios cables frágiles que aún la conectan a la placa lógica del iPhone.

    I just broke the cable to the battery!

    No Bama - Contestar

    same dude im such a freak lol omg haha

    Aiden Polaski - Contestar

    Are there replacements ribbons?

    Blax Bently - Contestar

    Has anyone else noticed very small squares of rubber with a circle cut through it (I think they fall off into the phone when dismantling)?

    I just replaced my screen and worked out that these are actually a wee pocket that slips over the pentalobe screw holes on the replacement screen. I’m not sure if it’s an additional water resisting mechanism or if it’s to add additional traction for the screws

    richarddillon - Contestar

    Thanks, I was wondering where those were from!

    Albert -

    I just broke cable connecting camera and earpiece speaker to logic board. Be careful with it.

    Natan Haładyn - Contestar

    This section is missing a critical step - to lay some Post-It notes or something below the right half of the phone when you swing it open, so the ribbon cables don’t get sliced by the sharp edge of the phone case. I broke the Home Button ribbon cable because there was no strain relief when I laid it open.

    neila - Contestar

    I also broke the home button cable and now I have to use assistive touch.

    Laurencio Gonzalez - Contestar

    Keep the suction cup on the display to keep it propped up while you disconnect the ribbon cables.

    minimalist - Contestar

    I broke the short ribbon cable that attaches underneath the lower connector bracket. Be SURE when you lift the display, you do it from left to right. I thought I had the phone oriented correctly in my hand, but I was mistaken.

    John Murray - Contestar

    Put the suction cup on the right side of the middle of the screen when you rotate it up and out. It serves as a nice stand to take the pressure off the connectors.

    Ray Bieze - Contestar

  13. Retira los siguientes tornillos triples Y000 del soporte del conector inferior:
    • Retira los siguientes tornillos triples Y000 del soporte del conector inferior:

    • Tres tornillos de 1.2 mm

    • Un tornillo de 2.4 mm

    • Durante esta reparación, lleva cuenta de cada tornillo y asegúrate de que cada tornillo vuelva al lugar exacto de donde salió para evitar dañar tu iPhone.

    Ahhh shoot! accidentally ordered tri-wing vs tri-point (must have just looked for y000).. It seems they only did this to annoy repair folks because not everything is tri-point on the phone...

    Steve - Contestar

    These screws just spin for me. They don't back out, but the heads aren't stripped either. I've tried applying backpressure to help lift the screws, but no luck

    Jeff Hurst - Contestar

    The Y000 took out one of the screws but not the other 3. I even tried the PH000 as suggested but nothing.

    dbright - Contestar

    What driver do I need to remove these screws i’m stuck

    Nasser Nader - Contestar

    i cant use, the Y000 it isnt working.

    joscarlos91 - Contestar

    What if I stripped a screw what do I do??

    Jacob Ramos - Contestar

    Yep, only the 2.4mm came out, other 3 won’t budge, and worried I’ve stripped the heads. Anyone got any ideas?

    Stephen Babbage - Contestar

    It’s the screwdriver bit that is the problem. I had the same issue with 2 Y000 bits not grabbing the screw properly. I fixed it by using a small 3 sided file to slightly grind the groves in the Y000 bit just a bit deeper. Then the bit worked like a charm on these screws.

    Jim Staples - Contestar

    Use Y000 on all 4. U have to be very sensitive on the 1.2mm screws. Put the bit in the screw, put the left pointing finger on top of the screwdriver and turn the driver carefully to the right until you feel a “bump”, thats the trick :-), then you are able to screw the screw out.

    Magne Eivindson - Contestar

    For me the key here was a LOT of downward pressure to ensure the Y000 bit caught in the screw. Not sure i can describe how much exactly, but is was significant. Otherwise the bit would not catch.

    Erik Fredriksen - Contestar

    What do I do if I Stripped one of them?

    Adam Corral - Contestar

    Can’t get them removed what to do ?

    cowling_luke - Contestar

    Managed to get the central one out. The upper one won't move, the lower one I've popped out with some force. This allows you to rotate the cover enough to unplug the various bits. Not ideal, but works. I've tried applying a lot of pressure, using the tighten/ loosen method, but the heads have just got mashed… no wonder Samsung are now No1, sigh…

    jimpoolio - Contestar

    You need to be careful when just rotating the cover as you can accidentally slice through the two black antennas! You only need to nip them…As you can tell I have done this in the past :/

    Kyle Webb -

    The first, longer screw came out fine, but the other three wouldn’t budge, regardless of more/less pressure or a slight angle or anything. I finally filed down the tip of the Y000 bit ever so slightly, and then it worked. Hope this helps someone.

    Harmony Vine - Contestar

    Filing down the bit worked for me. The tip about putting an index finger on the end of the screwdriver handles and then turning gently until it clicks into place was very helpful! Using these 2 tips I didn't need much downward pressure. Screws are out in a few turns.

    Chris Bennett - Contestar

    If you can’t get the bit to grip the screw properly, you can use a little bit of the water-proof sealing between the bit and the screw. That worked for me. Hope this helps anyone.

    jvalaamo - Contestar

    Mine came out easily. I placed the screws in the area where the bit goes in my kit so I can keep track.

    Gina Torres - Contestar

    I used a bunch of medicine cups to track my screws. You need like 12 if you want them all in cups. I ran out. There are so many different sizes that literally vary by 1mm. The tolerances on these things are tight.

    Ray Bieze - Contestar

  14. Retira el soporte del conector inferior.
    • Retira el soporte del conector inferior.

    my battery cable connector was stuck to the bottom of this metal bracket plate so be careful when you lift it off

    Josh Martin - Contestar

    This may have been intentionally done by Apple to make sure the battery gets disconnected before any other connector is disconnected. So always make sure to disconnect the battery before disconnecting and reconnecting the connectors for the display.

    Oscar Moreno - Contestar

  15. Usa la punta de un spudger para sacar el conector de la batería de su zócalo en la placa lógica. Dobla el cable del conector ligeramente hacia arriba para evitar que haga contacto con el zócalo y suministra energía al teléfono. Dobla el cable del conector ligeramente hacia arriba para evitar que haga contacto con el zócalo y suministra energía al teléfono.
    • Usa la punta de un spudger para sacar el conector de la batería de su zócalo en la placa lógica.

    • Dobla el cable del conector ligeramente hacia arriba para evitar que haga contacto con el zócalo y suministra energía al teléfono.

    Was kann passieren wenn man diesses Kabel vergessen hat zu entfernen `?

    Julian Eltrich - Contestar

  16. Asegúrate de que la batería esté desconectada antes de desconectar o reconectar los cables en este paso. Utiliza la parte plana de un spudger o tu uña  para desconectar los dos conectores inferiores de la pantalla haciendo palanca  hacia arriba de sus puertos de conexión en la placa lógica. Para reconectar estos cables, presiona un extremo hasta que encaje en su lugar, luego repite en el extremo opuesto. No presiones en el medio. Si el conector está ligeramente mal alineado, el conector se puede doblar y causar daño permanente.
    • Asegúrate de que la batería esté desconectada antes de desconectar o reconectar los cables en este paso.

    • Utiliza la parte plana de un spudger o tu uña para desconectar los dos conectores inferiores de la pantalla haciendo palanca hacia arriba de sus puertos de conexión en la placa lógica.

    • Para reconectar estos cables, presiona un extremo hasta que encaje en su lugar, luego repite en el extremo opuesto. No presiones en el medio. Si el conector está ligeramente mal alineado, el conector se puede doblar y causar daño permanente.

    • Si tienes un pantalla en blanco, líneas blancas en la pantalla, o no tienes respuesta táctil completa o parcial después de volver a ensamblar tu teléfono, intenta desconectar y reconectar con cuidado ambos cables y asegúrate de que estén encajados completamente.

    To be honest you don’t really need to disconnect the display cables in step 15 or 16 to get the battery out. Just keep the suction cup on the screen to keep it propped up and to give the cables some slack. The only reason to take these cables off is that it’s a pain to apply the replacement display adhesive with those cables in the way. If you’re not re-waterproofing your phone just leave these attached.

    Reemplazo Adhesivo de Pantalla iPhone

    minimalist - Contestar

  17. Remueve los dos tornillos Phillips 1.3mm que aseguran el soporte sobre el conector del sensor del panel frontal. Retira el soporte. Retira el soporte.
    • Remueve los dos tornillos Phillips 1.3mm que aseguran el soporte sobre el conector del sensor del panel frontal.

    • Retira el soporte.

    Has anyone had trouble getting these two screws off? I’ve been working on these for about 10 minutes and the LEFT screw wont spin. It seems like the little PH000 screwdriver bit won’t even grip it. (The one of the right comes off, no problem)

    It looks like I’ll have to pick this project up again with a screwdriver that will actually take off this piece.

    Makana Sylva - Contestar

    The right screw kept spinning, tried different levels of force but didn’t work. I left the screw on and bent the shield to get to the cable.

    s h - Contestar

    I used a #1 flat head tip to loosen.

    Peter Pearson - Contestar

    I couldn’t get the two screws out either—used the correct screw tip and everything. Stripped the screw. Will now attempt to just keep the cable attached…..

    Therese Peffer - Contestar

    Use the PH000 and apply a little more force before spinning, should come right out!

    Sierra Scolaro - Contestar

    ^To anyone having trouble, this is the correct answer. Put the phone on a firm surface, align your driver carefully, press down hard, and twist. As long as your driver is approximately the right size, it’ll come out.

    Jeff Suovanen -

    the two screw i have are stripped and i have n way of getting either screws off whats my next bet

    Alexis Marie Colon - Contestar

    The PH000 bit is to large. I can’t get the screws out either which really sucks…now I have to put everything back together, find another bit that will work and try this again another day. Not impressed with IFIXIT’s attention to detail so far :-(

    Ryan Welborn - Contestar

    Using iFixit’s driver kit, I prefer a PH00 for this, which is larger than the PH000. If you think the PH000 is too big, something is wrong.

    Jeff Suovanen -

    I think part of the issue with the iFixit PH000 is that it is slightly too pointy. The PH00 fits better because the splines engage the slots of the screw before the point bottoms out. The PH000 tip bottoms out in the screw’s center point and the splines don’t engage as well. I have other PH000 tips that are more blunt nose and they work better than the iFixit bit.

    rcarswell - Contestar

    Use the J00 bit. Worked perfectly

    efazio588 - Contestar

    PH000 screwdriver didn’t work for any of these screws, or the barometric vent, or the taptic engine. It was too big. I had to use a different screwdriver from another kit I had.

    minimalist - Contestar

    I’d do this step before removing the ribbon cables by the battery connector. That way you can disconnect all of them at the same time.

    Ray Bieze - Contestar

  18. Desconecta el conector del sensor del panel frontal de su puerto de conexión con la placa lógica. Este conector a presión  debe ser reconectado al finalizar en el mismo momento para minimizar el riesgo de que se doble.
    • Desconecta el conector del sensor del panel frontal de su puerto de conexión con la placa lógica.

    • Este conector a presión debe ser reconectado al finalizar en el mismo momento para minimizar el riesgo de que se doble.

    Das ist sehr mutig, das Kabel dort so zu strapazieren.

    Mich würde das Display daneben stellen und mit irgendetwas stützen, dass es nicht umkippen kann um Beschädigungen an dem Kabel zu vermeiden. Das reißt sehr schnell ein.

    Detlef Menninger - Contestar

    Is this the connector for the earpiece, as well? I did the screen replacement and everything worked, except now I can’t use my earpiece… I’m afraid I didn’t fully connect this particular portion.

    Victor Bui - Contestar

    @victorbui714 Correct, this is also the connector for the earpiece speaker. Check the flex cable carefully and make sure it wasn’t pinched or torn. Make sure the connector socket is clean (give it a blast with some compressed air if needed) and try reseating it. If that doesn’t help, you may want to remove the earpiece speaker and inspect the four springs on the back, and check that they’re intact and making good contact with the four circular pads on the flex cable. Give the pads a wipe with some IPA and try not to leave any skin oils on them. If none of that works, try replacing the entire flex cable/sensor assembly. Good luck!

    Jeff Suovanen -

  19. Retira el ensamblaje de la pantalla.

    When removing the screen, be aware of the two tiny square black rubber grommets on the Penelope screw brackets that secure the screen. They can fall off very easily and be lost without even knowing it (it happened to me, but was lucky enough to find them).

    Guy Cooley - Contestar

    Sorry, I’m so unclear about when to replace the Adhesive tape. Should I put the iPhone 7 Display Assembly Adhesive at this step, or after I’ve replaced the battery?

    Victor Bui - Contestar

    @victorbui714 Battery first, then adhesive during reassembly, as it says in the instructions. ;)

    Jeff Suovanen -

    This is the 3rd screen iv put in my phone and everyone them bust at the top by the camera every time iv bought one of these screen idk if it’s the manufactures fault or what?

    trent bost - Contestar

    @trentb28922 Ouch! That’s not normal. Is your phone’s frame bent? Are you having to use a lot of force when you install the display?

    Jeff Suovanen -

  20. Retira los cuatro tornillos Y000 que sujetan el soporte sobre el sensor de inicio / ID  Táctil:
    • Retira los cuatro tornillos Y000 que sujetan el soporte sobre el sensor de inicio / ID Táctil:

    • Un tornillo de 1.1 mm

    • Tres tornillos de 1.3 mm

    • Durante el reensamblaje, ten cuidado de no apretar demasiado estos tornillos, o el botón de inicio podría no funcionar

    Why is the screw over top of the home button so difficult to get out… has anyone else experienced this..? This is twice now I've struggled to get that screw

    Brandon - Contestar

    The screw to the left holding the heatshield is never mentioned in this guide

    Beerbo - Contestar

    No reason to touch that screw unless you’re removing the shield—in which case, this step instructs you to remove it.

    Jeff Suovanen -

    So I stripped the screw furthest to the left, how can i possibly remove it now? Can I just buy a new LCD shield and home bracket button and screw and will that work just fine on the new screen replacement? this stripped screw of mine is not coming out

    Bryan Ferrer - Contestar

    That should work, as long as you can still get the home button/sensor out without damage. For removing a stripped screw this size, I’d probably try supergluing it to the driver—or else just drill the top of the screw off and then remove the bracket, leaving the screw shaft embedded in the old display. Good luck!

    Jeff Suovanen -

    I used the same driver for all of these screws. Had to apply a lot of pressure before trying to unscrew it and it was fine.

    jessica harlow - Contestar

    This is wrong, the size you need is Y00 for the 1.1mm screws and Y000 for the 1.3mm one.

    Robert Clark - Contestar

    The heads on those screws are identical. I’ve never had any trouble using a Y000 for all of them. Use whatever works for you I guess.

    Jeff Suovanen -

    I’ve managed to strip the screw on the right hand side - not the far right, just right of the home button. Any ideas on how to get it out without glue (I don’t have any)

    Christie Ellen - Contestar

    My screwdriver is too big to get out the screws

    Coolinee Kerman - Contestar

    My eyesight isn’t what it used to be. That said, the replacement screen that arrived already had screws in the two outside positions. It took me a minute to figure this out when I was trying to install the home button. I couldn’t figure out why the screws weren’t going in. I thought the holes were filled or something… Nope. screws. Took them out and used them.. all good.

    Critter - Contestar

    My 7 had quite a bit of loctite holding these bad boys on. I stripped the one to the right of the home button and after using many “sentence enhancers” I was able to remove it using good tweezers and quite a bit of hand strength. I think that heating up the screws here is not an option because the cables lie underneath the plate and would probably get damaged from the amount of heat needed to loosen the loctite. Be patient here, and maybe have spare Y000 drivers because you may damage your driver getting these screws out.

    P Park - Contestar

    If your having trouble. I recommend you guys to buy the Y00o driver at amazon. It look golden. It works very will .

    Jonathan curz - Contestar

    Read instead of: “Remove the four Y000 screws”. “Remove the four Philips 00 screws”. Thats the case what occurs to me.

    Henk - Contestar

    Hi all, I’m really hoping someone will be able to give me a hand here, so the 1.1mm screw on top of the home button is stripped, and absolutely refuses to get out. I have tried the superglue technique mentioned and am worried it may have even glued the screw to the bracket. The only solution I can think of is to bend the home button bracket on either side of the middle screw, and use the bracket itself to remove the screw from the home button. I have ordered a new home button bracket either way, does anybody have any other ideas? Should I even attempt what I am proposing?

    Thanks in Advance.

    llamalulu42 - Contestar

    Does the ground strap go over or under bracket?

    Marcos Polos - Contestar

    my home button does not work anymore! do you know why?

    josé - Contestar

    I magically used an X-acto knife tip to lift the edges of the home button screw to loosen it, and then turned it slightly with the X-acto blade tip in the screw slot to get it started, then the 000 screwdriver could finish it.

    Jim Pflasterer - Contestar

    I can’t stress how important it is to not overtighten the one on the button. I undertightened the center one at first in fear, and then tightened it more when I realized the button was loose. It ended up ruining the home button :(

    Brendon Parker - Contestar

  21. Retira el soporte que asegura el sensor de inicio / ID Táctil.
    • Retira el soporte que asegura el sensor de inicio / ID Táctil.

  22. Haz palanca debajo del borde izquierdo del conector del cable del botón de inicio para desconectarlo de su zócalo. Si todo el conector comienza a levantarse sin separarse,   presiona hacia abajo el cable en el borde superior del conector con la parte plana de su spudger, mientras al mismo tiempo levantas el borde izquierdo del conector. Ten mucho cuidado de no dañar el cable o el conector, o desactivarás permanentemente el sensor. Si todo el conector comienza a levantarse sin separarse,   presiona hacia abajo el cable en el borde superior del conector con la parte plana de su spudger, mientras al mismo tiempo levantas el borde izquierdo del conector. Ten mucho cuidado de no dañar el cable o el conector, o desactivarás permanentemente el sensor.

    Well, I just damaged the home button connector in step 31. It is completely off the cable. What now? Can I buy this home button?

    LadyTech - Contestar

    I think you can not do it because your phone is not identify for new cable.

    Ali Alsaed - Contestar

    Best thing to do here is to NOT pry up on the connector, but to insert the pry tool on the left side until the connector is dislodged.

    Oscar Moreno - Contestar

    Good tip. Worked perfectly. Thx.

    Klaus M -

    That worked perfectly, thank you!

    Emily Kretschmer -

    use one pry tool to hold down, another to pull up.

    Christa - Contestar

    I did it. :-( i broke it

    Peter Keller - Contestar

    Anyone having difficulty reconnecting the two ? I’ve been trying for ages with no luck.

    Patrick McKenna - Contestar

    Same problem here - can reconnect them once the new LCD is being installed. Not sure what the trick is.

    edcraigslistaccount -

    my Homebutton don´t work after I reconnect all, I checked all flex cables but it still dont work. what can I do?

    Dr. Dieter - Contestar

    so, i’m working on an iPhone 7. I was very careful not to break anything, I even bought an iOpener heat pack and applied it, and everything went off without a hitch, but when I tested the button, It does not work, would it help to reconnect it or something?

    Thanks a lot!

    Peter Keller - Contestar

    iPhone 7 home “buttons” can be really fussy. You’ll find some good troubleshooting tips here and here. Hope this helps!

    Jeff Suovanen -

    Broke my cable. The picture is not clear but you have to separate the thin silver end of cable from what looks like a black piece of rubber. I pulled up on it from under the black rubber like the picture shows and broke mine.

    bart.hutchings - Contestar

    This helped me SO much. Watch it before removing home button. Around 4:56ish

    https://youtu.be/An9kUJshRjA

    Gina Torres - Contestar

    Thank you so much!

    Jakob Kloppenborg -

  23. Con cuidado levanta el conector subyacente y aléjelo del cable de inicio / ID Táctil. Es muy fácil dañar tu iPhone durante este paso. Trabaja despacio y ten cuidado cuando haces palanca con tu herramienta. Si dañas el hardware Touch ID, solo puede ser reemplazado por Apple.
    • Con cuidado levanta el conector subyacente y aléjelo del cable de inicio / ID Táctil.

    • Es muy fácil dañar tu iPhone durante este paso. Trabaja despacio y ten cuidado cuando haces palanca con tu herramienta. Si dañas el hardware Touch ID, solo puede ser reemplazado por Apple.

    • Si el conector no se levanta fácilmente, usa un secador de pelo o iOpener para calentar y ablandar el adhesivo que asegura el conector, y luego intente de nuevo.

    • No intentes desconectar el conector por completo; simplemente gíralo ligeramente para que el cable del sensor de inicio / ID Táctil subyacente se pueda extraer.

    Make sure that you fold this cable out when fitting your replacement before you fasten the shield back down. I didn’t but managed to loosen 2 screws on the shield to get the cable out.

    chris_sawyer - Contestar

    If you have isopropyl alcohol on hand. You can use it to help weaken the adhesive temporarily when lifting up the adhered home button.

    Ben - Contestar

    Just one tiny drop of isopropyl alcohol or it will reach the lcd screen.

    Stefano Restuccia -

  24. Al calentar el área alrededor del sensor de inicio / ID Táctil ayudará a suavizar el adhesivo que sostiene su cable delicado en su lugar, lo que facilita la extracción segura.
    • Al calentar el área alrededor del sensor de inicio / ID Táctil ayudará a suavizar el adhesivo que sostiene su cable delicado en su lugar, lo que facilita la extracción segura.

    • Da la vuelta al ensamblaje de la pantalla. Usa un secador de pelo o prepara un iOpener y aplícalo al borde inferior de la pantalla durante aproximadamente 90 segundos para suavizar el adhesivo que se encuentra debajo.

    If you don’t have that heating tool, a hair straightener n a T-shirt worked just fine for me

    www.tertlegerl - Contestar

  25. Utilice un pico de apertura para separar suavemente el adhesivo que sujeta el cable del sensor de inicio / ID Táctil en la parte posterior del panel de visualización. Utilice un pico de apertura para separar suavemente el adhesivo que sujeta el cable del sensor de inicio / ID Táctil en la parte posterior del panel de visualización. Utilice un pico de apertura para separar suavemente el adhesivo que sujeta el cable del sensor de inicio / ID Táctil en la parte posterior del panel de visualización.
    • Utilice un pico de apertura para separar suavemente el adhesivo que sujeta el cable del sensor de inicio / ID Táctil en la parte posterior del panel de visualización.

    It cannot be stressed enough that this is the one part of this repair that you can’t screw up. Anything else you’ll deal with during this repair can be easily replaced (The screen, and the sensor/microphone/camera assembly). Tearing this cable means an expensive trip to the apple store. or a very unhappy customer if you’re doing this for someone. Heat is your friend. I don’t even use a spudger or a guitar pick for this one, I use a new playing card to pull this up. Even with the card, you have to be careful. The edge of the playing card can nick the cable if you’re not careful to get it under the ribbon cable. If the adhesive isn’t soft enough for the card to get it up, apply more heat. Again, you can’t screw this step up. It’s all or nothing.

    Spartan99 - Contestar

    Well, no visible damage but the home button won’t work. I contacted a local Apple Authorized Service Center to check options. Since I had personally replaced the screen assembly, they wouldn’t even look at it per Apple policy. They said they would jeopardize their Apple Authorization if they even looked at it. Seems like more of the “Right to Repair” problem to me. Frustrated, but at least I have the accesibility home button working.

    bandman - Contestar

    Make sure the home button screws aren’t overtightened; that often causes issues. If there’s any damage to the button cable, a repair shop with a skilled microsolderer can patch a new cable on and restore functionality. iPhone 7 home button not working after screen replacement? Worst case scenario, you can also buy a screen repair from Apple, and they’ll include a new home button. I am not a lawyer, but the response you’re describing from the AASP sounds way out of bounds. Good luck!

    Jeff Suovanen -

    Just keep in mind that this is a very delicate step that requires a lot of patience. the part is attached to the body of the phone so firmly and there is no gap to put the opening pick under. So the way I did it was applying a good amount of heat onto the part and not from behind. I did it constantly for 5 minutes, a few minutes at a time, then I pulled the connected up slightly (a little too much pressure on the pull and you will break the wire). Pull it constantly and If the heat has been enough to melt the adhesive, it should come off easily and slowly.

    ashkan eslami fard - Contestar

    Hi, a little thing to help : i heatened up and then insert a cutter blade to start. Work better

    Crasset Renaud - Contestar

    Okay the home button is connected, as touch id works, but I can’t get any motion out of it. I backed off the screws, but that didn’t help. What else can I try?

    kathwick2 - Contestar

    Salve, vorrei un vostro aiuto, ho un problema con il tasto home (il tasto è originale preso dal vecchio display rotto) una volta sostituito il Touch ID funziona perfettamente (l’iPhone si sblocca e legge l’impronta digitale) il tasto invece no (il click per intenderci) cosa può essere? Grazie!

    bernabbo - Contestar

  26. Retira el conjunto de sensor de inicio / ID Táctil levantándolo por la parte frontal de la pantalla.
    • Retira el conjunto de sensor de inicio / ID Táctil levantándolo por la parte frontal de la pantalla.

    • Para reinstalar, primero introduce el cable a través del orificio en la parte frontal de la pantalla.

    • Tu parte de reemplazo puede venir con un tornillo extra Y000 ya instalado en el Botón de Inicio. Remueve el tornillo innecesario así puedes reinstalar el soporte de botón de inicio.

    True to this picture, the home button can only be removed (and put back in place) through the front of the LCD assembly.

    Talon - Contestar

    Very good comment Talon. That was the first thing I was looking for here. There should be a bullet point in step 24 - Carefully remove home button from front of display being careful not to damage cable.

    Tracey - Contestar

    Had an issue when putting the screen back on, the side where the cables attach would not sit flush. At first I thought the cables were pushing the screen up. Turned out to be the battery cable shield was just a fraction too far down toward home button. After loosening screws, nudging it up slightly and screwing back in, the screen sat flush as it should. In case anyone else has same issue.

    jbarry - Contestar

    Is there anything special about reassembling the "home" button ?

    I tried several times with several buttons but none works.

    Lambiel - Contestar

    must use original button

    Christa -

    My phone is no more turning on after I replace the screen, no reaction if I press home button or power button

    cheryl.iseli - Contestar

    Why doesn’t this tutorial also cover the earpiece assembly?

    James - Contestar

    This guide is missing the camera transfer and the stupid little black sticker on the earpiece assembly that causes the earpiece not to work if that sticker is not transferred. This guide is wholly incomplete

    Mason Schild - Contestar

    James and @computermason—You’ll want to look up the correct guide for your repair, especially if you’re not using one of the kits for which this guide is designed. The guide for transferring all the smaller components is here.

    Jeff Suovanen - Contestar

    No home button functionality? I just watched a video on YouTube from two years ago saying that the iPhone 7 and 7+ have to be taken to an Apple repair center for the home button to work. Is this still the case? If so why didn’t you tell me this before I ordered this! Please confirm before I start warning everyone not to purchase from you!

    Gregory Haycock - Contestar

    @ghaycock If you’re replacing a screen, the home button will work fine as long as you carefully remove it from the old screen and transfer it to the new one, exactly as explained in the guide. The button itself can’t be replaced without help from Apple (which is why iFixit doesn’t sell home buttons for this model).

    Jeff Suovanen -

    One thing I don’t see mentioned is the replacement of the rubber gaskets that are on the pentalobe holes. The replacement screen did not come with these on it. I was able to remove them from the OEM screen, but there was no easy way to get them to adhere to the new screen. If they move just a little, you might not be able to properly thread the pentalobe screws. Worst case is that they fall into the body of the phone during this last step of re-assembly. At that point, you’ve already started to have the screen stuck to the adhesive, so you would need to redo the entire adhesive gasket.

    You can see the gaskets in this picture: https://d3nevzfk7ii3be.cloudfront.net/ig...

    Here they are near the new screen: https://drive.google.com/open?id=14FwpSB...

    Andre LeBlanc - Contestar

Conclusión

Para volver a armar tu dispositivo, aplica el adhesivo de pantalla y sigue estas instrucciones en orden inverso.

548 personas más completaron esta guía.

Un agradecimiento especial a estos traductores:

100%

Estos traductores nos están ayudando a reparar el mundo! ¿Quieres contribuir?
Empezar a traducir ›

Evan Noronha

Miembro Desde 05/02/15

179,485 Reputación

177 Guías creadas

Equipo

iFixit Miembro de iFixit

Community

107 Miembros

9,566 Guías creadas

When putting the screen back on will the device loose it's water-resistant properties?

Joseph - Contestar

Wondering this too.

Draydan -

It will for sure lose it's water-resistant properties. So, please replace the water-resistant adhesive before assembly.

Jojo -

Yes, but you can buy a new replacement seal for a few bucks. However, it is extremely thin and very sticky so its almost impossible to do it right the first time (imagine placing a needle thin sized rubber band covered in glue around the tiny ledge you phone screen sits on). I would suggest you buy two because it is likely you’ll need a second shot at it…because if any part gets misplaced and sticks to the wrong spot, it will not come off, and that “sticky rubber band” turns into this horrible stringy tar/chewing gum ring that is impossible to manipulate…fair warning… it will most likely be pretty water resistant even if you don’t add a new seal to it… its not a waterproof phone in the first place :)

jaicdc -

Yes it will lose the water-resistant abilities. It is very hard to seal it back to it's original state.

Alec - Contestar

Is there any supplier that sells the original adhesive for the edge of the phone so we can make it better? Or do we have to just wing it with some cut double sided tape etc?

Grant Ormsby - Contestar

The short answer is yes, there are suppliers who carry the adhesive. It can be difficult to obtain and may be tempting to go for a replacement from eBay or somewhere similar, but I advise to steer clear of unverified vendors. If you can get one from iFixit, I strongly recommend that you use them - especially if you're only purchasing one for a DIY project. If iFixit doesn't have them, you can get these from Union Repair as one option. http://www.unionrepair.com/replacement-f...

Joshua -

We do offer the replacement adhesive if you need it—I wouldn't recommend trying to wing it. By the way, the phone will work fine without replacing the adhesive (it just won't be as waterproof), so if you don't have the adhesive on hand, it's perfectly okay to finish your repair and close up your iPhone, and then replace the adhesive at a later date.

Jeff Suovanen -

The adhesive is sold here but its sold out, you can find it on eBay tho

Hernandez5827 - Contestar

I am curious about the home button transfer? transfer from old cracked to new screen and finger print will work? also I have read online forums using 3rd party screens for gens i6/i6s/i7 and doing an iOS update will brick and or make the finger print scanner unusable? Can anyone confirm?

Thanks.

hawaii4vr - Contestar

The issue with the Home Button not functioning and "bricking" the device was not from 3rd party displays. It was from shops not transferring the Home Button to the new assembly. During restore or update the device would deliver Error 53. Apple has since modified iOS to not do this, so it is no longer the concern that it was. As long as there is not anything wrong with your Home Button, it will be fully functional on your device after the new display is installed.

Joshua -

Keep in mind that while you are safe using third party screens, using a non-original home button will result in losing TouchID functionality.

Evan Noronha -

That home button cable is a bit tricky. I came at it from the top side of the home button with the pointy end of my spudger, and managed to pull up all of the adhesive. otherwise, this was a pretty straight forward swap.

Bradley Breedlove - Contestar

Anybody having issues with the replacemnt screen flex putting pressure on back of the lcd when its put back together? I don't know if its a defect because its my first time!

Astralzombie - Contestar

Thats quite easy. Thats the ‘block’ on the bottom left of the screen. Make sure it aligns nicely.

Beerbo -

This guide feels incomplete without the disassembly of the smaller parts on the display assembly.

Sverre Siggerud - Contestar

I agree since these guides are intended for newer repair techs or DIY people that should have been added in

Don -

I agree with @Sverre Siggerud

gra_allax -

I agree it's missing a large portion of the work

Gaspard Leon -

tbh this is one of the worst guides on here. It goes about 30% of the way into the whole job. No instructions an removing backplate/shield, camera assembly or home button which are by far the trickier parts of this job. 4/10 could do much better!

gra_allax - Contestar

There are other guides that gives the directions on removing the other parts ..you just have to find the guide for each part ...the guide for removing shield plate pretty much covers it all

Jaye -

exactly! was in the middle of the job when realised the the guide was incomplete, had to guess by myself

victor maia -

I’m sorry to hear that! From what it sounds, your replacement part is actually the LCD and digitizer, not the complete screen, which is listed in the parts section. The screen part comes with everything pre-installed for easy replacement, while the LCD and digitizer comes with nothing installed and requires much more disassembly.

Arthur Shi -

I replaced the screen of iPhone 7 , after using couple of hours its opening & closing apps by itself .i restore it still didn't work if I restart it will work couple of hours then start again same issue .

Malik Adam - Contestar

Tip for anyone who is moving the home button to a replacement screen. The cable is stuck on the screen pretty good with adhesive, I found that an easy way to get it off is to use a very very small flathead screwdriver (I used the smallest one in the iFixit tool kit) and carefully pry the cable off starting where the little plastic pin pokes through the hole in the cable. Came right off and the adhesive was still stuck to the cable. Just don't puncture the cable.

Evan Smith - Contestar

STEP 9: WARNING IS STUPID.

WHO CARES if you break the plastic clips? You're replacing the screen which has NEW plastic clips.

STEP 14. DO NOT lay it down like an open book. The cables are likely to tear if you do this because they are very short and snug. I recommend placing a heavy object behind the screen to keep it propped up/open like a laptop screen.

STEP 15. CLEARLY IT IS NOT laying down like an open book. In fact not until step 19 does it look like it's laying flat like an open book.

To the above comments. Send it to Apple if you want the WATERPROOFING to stay intact. Of course you'll likely get a refurbished phone in return. Here's a novel idea. Don't get your phone (or any other electronics for that matter) wet.

paul bunions - Contestar

Thanks for the info. I was just thinking about Step 14 and if the cables would be long (or strong) enough. You answered my question ;-)

Clems -

You're right that broken clips might not matter if you're just replacing the screen—however, the warning in step 9 is necessary because this step (opening the phone) is a prerequisite for all iPhone repairs (not just the screen). I agree with you about the cables being too short in some cases to lay the display flat, and I've deleted the note about laying it down like an open book. Thanks for your comments!

Jeff Suovanen -

http://www.unionrepair.com/replacement-f...

@joshua, thanks for the link, that i much cheaper then in the Netherlands.

Btw how is the quality of the lcd screens for example?

Ron Schuts - Contestar

To whom ever posted this tutorial,

I think you explained well.Some people always have some type of negative feedback. There are other tutorials for removing the shield and etc. Just do a little research people. Also if warnings are put in place you best believe someone made that mistake. If you all have a problem with his tutorial you all go out your way and make one. Keep up the good work!

Kaila Freeman - Contestar

When I took off the home button, a small black square rubber piece fell out. while prying off the cable.

Can anyone tell me where this is supposed to go when I put the home button back on.

Joe in PA - Contestar

That is the button seal. Goes between the front screen and the button.

122654 -

You guys need to provide some instruction on the removal of the home button, its changed since the older phones.

Andrew spoelstra - Contestar

I work in a phone repair shop. We have had an on/ off problem for the 7/7+. Sometimes if you unplug the camera from the board and attach it to the new screen then back to the board it will boot loop. So we've taken the precaution to not unplug it. Do you know if this is a software or hardware problem? If so, which part of the software/hardware should we be more careful about when repairing?

The only way to stop the boot loop is to unplug the FF camera which puts the customer out of a selfie camera and makes the repair redundant.

Thanks

Marsha Brady - Contestar

I am experiencing this right now. I am currently trying to restore the phone for like the dozenth time when I came across this. As soon as it’s done this time I’m going to try unclipping the front camera assembly. Have you tried getting the phone out of the boot loop and then clipping the earpiece assembly in while it’s on the home screen? I know we aren’t supposed to be playing with the innards while its on, but desperate times…

Tom Kavarnic -

Sometimes--- there is a pressure point underneath the LCD on the right side of the screen when closing the iPhone 7 (where the bracket covers the cables under the LCD, not the proxy connector). It's been hit and miss. Some repairs can be done and there is no pressure point, then for others, it seems the chip is sitting on top of the metal bracket and causes a pressure point when closed. Has anyone else had this issue? What have you done to make sure it's not an issue 100% of the time?

aqnguyen87 - Contestar

The pressure point is because the chip is moved a little bit upwards to the phone when changing to a new screen. Try to relocate the chip 0,5mm-1mm further down on the screen and this will fix the pressure point occurring when closing the screen to the phone!

Erling Andre Saethervik - Contestar

please help

i have replaced the screen with another working screen and i opened the screen very slowly as i should without touching the right side cables of the screen than i removed the bracket from the bottom of the lcd connectors and removed the battery connector first than the lcd connectors and than removed the top connector by the camera…the problem is im having a black screen i reconnected the old screen and now same issues…what did i do wrong and how to fix this black screen…what could have i done…if i removed the battery connectors first….

sam - Contestar

Pk so i replaced and the screen and now working fine..but fromt camera does notvwant to work even after i changed thefkex cable…no bent no issues…what is the issue…i did reset still no front camera i did reboot power+volume down still same issue what did i miss??

sam - Contestar

What is the function of the 1.1 mm screw located in the plate securing the touch I/D sensor in position, the screw is located directly in the centre of the touch I/D sensor.

costadelsol

Neil Rodgers - Contestar

It holds the touchid sensor in place. Duh :p

Beerbo -

How To fix black screen when I touch home button screen will not light up and phone tells me to enter password

jordansm80 - Contestar

You really should have included the camera as well,

gocaps25 - Contestar

I am having issues with the home button swap.

I have replaced a damage screen from another damaged iPhone.

One iPhone had hardware issues that made the phone basically useless (no service, ever, could not restore firmware from iTunes) this device had a perfect screen.

The other iPhone had a shattered screen.

So I am replacing the shattered screen with the screen from the other iPhone, and swapped the home buttons.

The phone with the now new (uncracked) screen doesn't recognize the home button at all. Nor does it tell me that I have the wrong home button when I purposely connect the wrong home button.

I took the same home button and put it with the other iPhone and the iPhone rejects it (point is, it detects the home button). The other iPhone doesn't even detect it.

cadearmstrong - Contestar

Everything went well and smooth on installing screen, but when I started testing my iPhone it seems it has some sort of interference when using the front and rear recording camera. All my recordings come out with a pretty loud static and clicking noise on the recording . Is it possible that the screen is interfering with my Front and rear camera mic camera? Can someone help me out please?

lmatiasjr - Contestar

Worked really well, make sure that you really heat up the home button adhesive, if you lose 1 or 2 screws per bracket, it’ll still be ok BTW

Coolinee Kerman - Contestar

Bought a replacement kit that not only left out the splunger, but gave my three unmarked screwdrivers. (all I needed was the pentalum ) stripped the screws, not even super glue could get them out. Utter failure .

MajorCouillon - Contestar

Wanted to reply to my own text.My failed attempt had nothing to do with these in-depth directions , it had to do with my failure to purchase tools from the correct company.this sight has helped me repair my ps3 and offered countless other insights. I was just in one of those moods I’m sure most of us can relate to. Oh, and , excuse me while I do this….. AAAPPPPLLE!! Grrr

MajorCouillon -

Does automatic brightness work for you after replacing the screen with the iFixit part? Mine was working properly with the original screen, but auto-brightness doesn’t seem to work with the iFixit replacement.

AlexVaq - Contestar

Hey i tryed to fix my iphone 7 which had screen brokedown with a collision i think it can b a issue of some loose connection or someting boke out the phone is not responding to anything no display so vibration i tried to change it for too long i din’t even heat up what can b the issue will ut work agian plz reply im a student and cant aford to buy new phone or waste money on old one i alredy got its screen replaced but its noe working yet plz… help me out with a professional advice it will be gratefully

Thank you

jashandeep.0052@yahoo.com

Jashandeep - Contestar

Salve ,

mi spiegate perché quando sostituisco il gruppo display e lo vado a rimontare mi rimane sollevato sulla parte dei flat?

è come se non entrasse, eppure sembra tutto ok e ben posizionato.

Grazie anticipatamente della risposta e complimenti per la guida.

Riccardo Mazzoni - Contestar

Hi,

I swapped a broken Iphone 7 screen and everything seemed to work fine even fingerprint.. But the front camera did not work after the swap, so i installed a new one and a battery, and now camera still doesnt work, and there is a vertical black line in the screen. Someone knows what went wrong?

Jonez - Contestar

I have a strange problem. i had a iphone 7 with the audio ic problem, so got another working one with a cracked screen. I have just switched the board and button from the good one to the broken audio ic one. now fingerprint ID works fine, but i am getting no haptic at all from the button. the phone works fine. both phones had button haptic before the swap.

sam caspian - Contestar

sorted it, tried reconnecting the cables, no joy. in the end i swapped over the taptic motor, and its fine now. I also swapped out them tri screws for normal + ones from all my spare parts.

sam caspian -

Thank you!, Evan Noronha (and 8 other contributors). Using this guide, I was able to disassemble and assemble back the screen. I will keep the forum posted for any other problems.

Hariharan Hariharasubramanian - Contestar

If you tore the top ribbon cable for the camera and what not, can you stil replace the screen and it work?

Kate Godfrey - Contestar

Why are all of these “replacement” guides actually just disassembly guides? You always cut the instructions off halfway. This doesn’t show anyone how to replace anything, just how to remove the screen and other connected components. How much extra effort would it actually be for you to include the rest of the instructions? Like 5 more photos per guide?

Josh O'Brien - Contestar

I believe it’s possible to create your own iFixit guides.

I’ve never had an issue with this. I mean sure it’d be nice, but for such a prolific and constantly updated resource, I don’t see the point in complaining too much about it. I’ve never felt like they don’t give me enough to complete a repair.

Sam -

In terms of this particular guide, the only thing missing in my opinion is removing the front sensor flex cable, earpiece speaker and backplate, but since many displays come with those parts attached I can understand the exclusion. At the end of the day, a disassembly guide is all one really needs for these repairs since you can follow the instructions backwards to install the new part once the broken part is disassembled, so adding steps for that seems somewhat redundant.

Sam -

Is it possible to replace the display without the adhesive? Or is it absolutely necessary?

Bryan Young - Contestar

You can it just won’t have the water resistant seal that the adhesive provides

jonathan whittington -

A tiny drop of super glue holds the plastic camera holder in place

Paul O'Donohoe - Contestar

Anyone found a way of getting the 3 1.2mm screws out? (step 13) They just won’t budge, and I think I’ve stripped the heads… What now?

Stephen Babbage - Contestar

Excellent guide. Thank you very much

Larry Welch - Contestar

I replaced the screen using this guide, however now Apple Pay doesn't work. Has anyone else experienced this? Is there a fix?

Dave - Contestar

I’ve just replace my Girlfriends iPhone7 screen and now she doesn’t have an screen rotation. I may have got some of the screws mixed up. I read somewhere about a magnetic screw in the wrong place can cause this. Does anyone know which screw I might have got wrong?

Mike - Contestar

I just replaced my screen with an original one from an board fried iPhone. Now when on it says it won’t recognize the touch id and directly shows on screen the white button. I have checked twice and no clue why. Any help?

Juan Herrera - Contestar

Are y’all sure this fix guide is for the iPhone 7 because the screen in this guide has 3 ribbon cables 2 at the bottom and 1 at the top but the one I ordered only has 2 both being at the bottom so I thought they sent me the wrong one so I sent it back and ordered one from someone else and it had only 2 both being at the bottom so I’ve come to a conclusion that this guide is incorrect

jonathan whittington - Contestar

Nevermind I see it doesn’t have the front facing camera preinstalled

jonathan whittington -

The screen you ordered is a screen without the camera and the speaker. The third cable that you are looking for is that of the camera and speaker, which will need to be transferred from the original screen as well as the shield.

yvaneck - Contestar

I just ordered the correct one with the camera and speaker pre installed but what do you mean by the shield

jonathan whittington -

i just finished putting my new screen on but when i turned my phone on it said your home button may need service but i was sure not to over tighten the screws around the touch id sensor like it said not to… what do i do now???

awhitt23 - Contestar

Took my time with this one and the odds were in my favor….Nailed this slightly novice repair!!!!However I could have used the precut waterproof gasket ifix offers instead of the roll type ….

Bryant Trambaugh - Contestar

complete thanks to the cool ones at ifix…thanks yall

Bryant Trambaugh - Contestar

What exactly is meant by rocking the screen? I can’t lift this thing for the life of me.

Anthony - Contestar

I’m having a problem with the home button not working after I replace the screen. I’ve never had this problem with the lower models before. If over tightening the screws is the problem, how tight do they need to be?

Carson - Contestar

Salve vorrei un vostro aiuto, il tasto home (preso dal vecchio display rotto) una volta sostituto il Touch ID funziona perfettamente (l’iPhone si sblocca e l impronta viene letta senza problemi) il tasto invece no (il click per uscire dalle app per intenderci) cosa può essere? Grazie per l’aiuto!

bernabbo - Contestar

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 663

Ultimos 7 días: 4,448

Ultimos 30 días: 22,042

Todo El Tiempo: 677,671