Saltar al contenido principal

Repara tus cosas

Derecho a reparar

Tienda

Introducción

Sigue estos pasos en esta guía para reemplazar el ensamblaje del botón de inicio, incluyendo la junta y el cable en tu iPhone 6s Plus. Ten en cuenta que los botones de inicio están emparejados con su respectiva placa lógica, así que el Touch ID no seguirá funcionando luego de reemplazar el ensamblaje del botón de inicio.

Puedes también reemplazarsoporte de botón de inicio.

  1. Antes de desarmar su iPhone, descarga la batería por debajo del 25%. Una batería de litio-ion cargada puede incendiarse y / o explotar si se pincha accidentalmente.
    • Antes de desarmar su iPhone, descarga la batería por debajo del 25%. Una batería de litio-ion cargada puede incendiarse y / o explotar si se pincha accidentalmente.

    • Apaga su iPhone antes de comenzar el desensamblaje.

    • Retira los dos tornillos Pentalobe de 3.4 mm a ambos lados del puerto Lightning.

    Make sure you use the correct screw driver tip to remove these screws, which for the iPhone 6s Plus is the P2, otherwise you may strip the tip of the screw making it 10 times harder to remove. If once the screw is lose, it will not come off, use a magnet to remove it.

    Miguel Perez - Contestar

    If I do it by myself, will it damage the water resistant strip?

    I know iphone 7 have it ,but I am not sure 6s plus have it.

    Ganqian Zhu - Contestar

    iPhone 6s has an adhesive gasket under the display, similar to the iPhone 7—however, it doesn’t add much in the way of waterproofing since the 6s has non-sealed openings in other parts of the phone. Water resistance on the 6s is primarily internal (seals around the logic board connectors, etc.). It may still be worthwhile to replace the adhesive on the 6s in order to help keep the display firmly seated so it doesn’t move/wobble at all under pressure, but the phone will continue to work fine whether you replace the adhesive or not.

    Jeff Suovanen -

    Salve nella procedura iniziale di smontaggio display con la ventosa non è menzionato il fatto di scaldare i lati del display per “ammorbidire” la striscia che incolla il display alla scocca.

    Non è necessaria la cosa o è consigliabile ?

    grazie

    Hello, in the initial disassembling procedure with the suction cup, it is not mentioned how to heat the sides of the display to "soften" the strip that glues the display to the body.

    Is not the thing necessary or is it advisable?

    thank you

    Daniele - Contestar

    You’ve probably received your answer by now but for future enquirers, it does help the process of taking the screen off if heat is applied to the screen. If you have a hair Dryer use that on a low setting to heat the edges of the screen until it’s almost too hot to touch then slip very thin metal spudger around the edge to cut the adhesive. The carefully lift the screen with the help of the spudger and continue with your repair

    Cheers Wayne

    Wayne Lyell -

    How do I know that the Battery has ZERO Charging Cycles on it when it arrives ? Is there a (downside) to Higher Capacity batteries ? It is INCREDIBLY DIFFICULT to maintain a “Zero Chinese Products Lifestyle”, so how do I know that I’m not getting a deficient Chinese battery, potentially a refurb. battery ?

    integritybuilders - Contestar

    When your repair is complete, you can use coconutBattery to check your new battery stats and cycle count. (A properly tested battery may already have a charge cycle or two on it.) Avoid higher capacity batteries on iPhones—they’re generally either gimmicks, unsafe, or both. As far as the quality of the part, that comes down to how much you trust your supplier and whether they guarantee the product.

    Jeff Suovanen -

    So I need to empty the battery to zero percent?

    johnpatrickanat - Contestar

    Below 25%, exactly as stated in the instructions. There’s no benefit to draining it further than that, and in fact you’ll slightly shorten the service life of the battery by draining it all the way to zero. Follow the instructions exactly as written—if you go off-script, you’re a lot more likely to break something.

    Jeff Suovanen -

    So my screen shattered completely and the screen first had colored lines on tge while right side then it went out completely. If i get an lcd and digitizer replacement I'd that oing to fix it

    shellietheleo - Contestar

    I would initially recommend a well-lit, comfortable area and placing the screws on a white piece of paper with the screw sizes written down (apparently there are magnetic mats, also). Also, I found placing the phone on a paper towel is good so that if a screw is dropped, it will lessen the likelihood of bouncing away.

    Lou Fazio - Contestar

  2. Al abrir la pantalla en el 6s Plus, se separa una delgada tira de adhesivo alrededor del perímetro de la pantalla. Si prefieres reemplazar el adhesivo, ten listo un conjunto de nuevas tiras adhesivas antes de continuar. Es posible completar la reparación sin reemplazar el adhesivo, y probablemente no notarás ninguna diferencia en la funcionalidad.
    • Al abrir la pantalla en el 6s Plus, se separa una delgada tira de adhesivo alrededor del perímetro de la pantalla. Si prefieres reemplazar el adhesivo, ten listo un conjunto de nuevas tiras adhesivas antes de continuar. Es posible completar la reparación sin reemplazar el adhesivo, y probablemente no notarás ninguna diferencia en la funcionalidad.

    • Aplica una ventosa en la esquina izquierda inferior del ensamblaje de pantalla.

    take out screws first!!

    Yoav Karmon - Contestar

    Make sure you use the right screw driver tip for i phone 6s Plus, which is the P-2. If the screw will not come off once is lose, try using a magnet.

    Miguel Perez - Contestar

    My cracked screen prevented the suction cup from sealing. SOLUTION: With a piece of clear packing tape across the screen, the suction cup will seal and pull.

    Jim Cowles - Contestar

    I broke my iphone screen in the first step!

    Pierre Bertram - Contestar

    This screen removal step got more wrestley than I anticipated. The adhesive is quite strong. I used a flat-ended razor tool that I have to begin the prying - I don’t know how I would have got it started without this.

    Lou Fazio - Contestar

  3. Tira de la ventosa con una presión firme y constante para crear un ligero espacio entre el panel frontal y la caja posterior. Tirar demasiado fuerte puede dañar el ensamblaje de la pantalla. Aplica la presión necesaria para crear un pequeño espacio entre el ensamblaje de la pantalla y la caja posterior.
    • Tira de la ventosa con una presión firme y constante para crear un ligero espacio entre el panel frontal y la caja posterior.

    • Tirar demasiado fuerte puede dañar el ensamblaje de la pantalla. Aplica la presión necesaria para crear un pequeño espacio entre el ensamblaje de la pantalla y la caja posterior.

    I had a shattered front glass panel so I could not get the suction cup to seal properly. I tried a couple of different ways to get good suction but to no avail. I eventually used a Stanley knife to pry up the corner so I could get the spudger into the opening.

    John Architzel - Contestar

    A really high quality packing tape over the entire screen will usually be enough to use the suction cup on a shattered screen.

    djwooten -

    I used a suction cup on each side to provide counter traction. I braced the iphone between my knees and pulled apart while my helper inserted the spudger

    jkanne - Contestar

    This was by FAR the most difficult part of this whole thing. I confess the spudger was not cutting it so I used a butter knife to get into the small opening first, then used the spudger to go around the screen.

    Julie Sanchez - Contestar

    Hey everyone, if you never have done this part before be aware there is an extremely strong adhesive around the lip of the screen and once again is extremely strong. I had to get a friend to insert the pry/pick into the small gap while I used one hand to brace the phone down and the other to pull the suction cup without it digging into my hand. Go slow, it took me 5 tries because I didn’t realize how strong the adhesive was.

    bartmistrot - Contestar

    I also had a badly cracked lower screen - that glass was actually threatening to pull off the phone in chunks during this step, even with packing tape. Resorted to @j2arch’s tip and inserted a utility knife vertically into the seam between the display and phone body. Was able to lever the glass enough to get the spudger in there.

    Jason Augustyn - Contestar

    I have replaced sevrel screens for my sister in law and my niece. The packing tape has worked every time and that’s with it Shattered and pieces already falling out. You have to make sure the packing tape goes to the edge of the screen but doesn’t touch the frame. I have the plier like screen remover and use that it is much easier to remove the screen by your self with that tool. I also have the little finger suction cup that comes with the kit here. I bought the plier suction cup tool When I had to replace the screen that had the pieces of the screen missing and I don’t regret spending the extra money for that it has made a world of difference. I do this as a hobby it’s not a job for me. The electric divide repair kit from Lowe’s is also a very good kit to help. If you’re only going to do it once the kit that comes with the package is a great deal from ifixit. Well worth the money to spend the little extra to get the kit if you all ready don’t have the tools.

    Brent - Contestar

    If you try to use the spunger near the home button and try to pry it can crack your screen. This happened to me.

    Jeffrey - Contestar

    I found it easiest to use two suction cups. One on the front as directed, and a second one on the back. Give the spudger to your assistant, and have them slip it in place while you pull the display from the case.

    gordojenkins - Contestar

  4. El lugar más seguro para hacer palanca es la muesca en el panel frontal sobre la toma de auriculares. Mientras mantienes la presión sobre la ventosa, inserta la punta plana de un spudger en el hueco, directamente sobre la toma para auriculares. Mientras mantienes la presión sobre la ventosa, inserta la punta plana de un spudger en el hueco, directamente sobre la toma para auriculares.
    • El lugar más seguro para hacer palanca es la muesca en el panel frontal sobre la toma de auriculares.

    • Mientras mantienes la presión sobre la ventosa, inserta la punta plana de un spudger en el hueco, directamente sobre la toma para auriculares.

    This was by far the hardest part of the repair for me. Getting leverage while finding a way to prod with a spudger is a challenge in coordination. I used a second spudger with point holding the phone down by the headphone jack, with the other end of the spudger anchored to my desk.

    drpotter - Contestar

    When warmed, the suction cup was useless. Using the tip of a knife blade, was able to get it separated enough to insert spudger.

    hutland - Contestar

  5. Gire el spudger para ampliar el espacio entre el panel frontal y la caja trasera. Gire el spudger para ampliar el espacio entre el panel frontal y la caja trasera.
    • Gire el spudger para ampliar el espacio entre el panel frontal y la caja trasera.

    just changed the screen, but due to the tape along side the screen , it is best to heat a little so the glue losses and you can get the screen off better, like indicated

    Bart Blanckaert - Contestar

  6. Mientras tiras firmemente de la ventosa, desliza el borde del spudger debajo de la esquina inferior izquierda de la pantalla. Mientras tiras firmemente de la ventosa, desliza el borde del spudger debajo de la esquina inferior izquierda de la pantalla. Mientras tiras firmemente de la ventosa, desliza el borde del spudger debajo de la esquina inferior izquierda de la pantalla.
    • Mientras tiras firmemente de la ventosa, desliza el borde del spudger debajo de la esquina inferior izquierda de la pantalla.

  7. Desliza la punta del spudger por el lado izquierdo del teléfono, entre el panel frontal y la caja posterior. Desliza la punta del spudger por el lado izquierdo del teléfono, entre el panel frontal y la caja posterior.
    • Desliza la punta del spudger por el lado izquierdo del teléfono, entre el panel frontal y la caja posterior.

  8. Inserta la punta plana del spudger debajo del borde derecho de la pantalla. Desliza el spudger por el lado derecho.
    • Inserta la punta plana del spudger debajo del borde derecho de la pantalla.

    • Desliza el spudger por el lado derecho.

  9. Usa una herramienta de apertura de plástico para mantener presionada la caja trasera mientras levantas la ventosa para abrir el teléfono. No retires la pantalla por completo o dañarás los cables de datos que la conectan cerca del borde superior del iPhone.
    • Usa una herramienta de apertura de plástico para mantener presionada la caja trasera mientras levantas la ventosa para abrir el teléfono.

    • No retires la pantalla por completo o dañarás los cables de datos que la conectan cerca del borde superior del iPhone.

  10. Tira de la pequeña protuberancia de la ventosa para extraerla de la pantalla. Tira de la pequeña protuberancia de la ventosa para extraerla de la pantalla.
    • Tira de la pequeña protuberancia de la ventosa para extraerla de la pantalla.

    Remember to apply the screen gasket on the re-assemble. The gasket is provided in the kit but not mentioned here on the instructions.

    Won Hong - Contestar

    There’s a link to the entire gasket replacement procedure in Step 21.

    Jeff Suovanen -

  11. Sujeta suavemente el ensamblaje de la pantalla y levántalo para abrir el teléfono, utilizando los clips en la parte superior del panel frontal como bisagra. Abre la pantalla aproximadamente a un ángulo de 90º, e inclínala contra algo para mantenerla apoyada mientras estás trabajando en el teléfono. No abras la pantalla más de 90º; aún está conectada a la parte superior del teléfono por medio de la pantalla, el digitalizador y los cables de la cámara frontal, que pueden romperse fácilmente.
    • Sujeta suavemente el ensamblaje de la pantalla y levántalo para abrir el teléfono, utilizando los clips en la parte superior del panel frontal como bisagra.

    • Abre la pantalla aproximadamente a un ángulo de 90º, e inclínala contra algo para mantenerla apoyada mientras estás trabajando en el teléfono.

    • No abras la pantalla más de 90º; aún está conectada a la parte superior del teléfono por medio de la pantalla, el digitalizador y los cables de la cámara frontal, que pueden romperse fácilmente.

    • Agrega una banda elástica para mantener la pantalla en su lugar mientras trabajas. Esto evita una tensión excesiva en los cables de la pantalla.

    • En caso de necesidad, puedes utilizar una bebida enlatada sin abrir para apoyar la pantalla.

    if the display cables are damaged how can you tell ?

    Smiley McSmilebot - Contestar

  12. Remueve los dos tornillos Phillips que sujetan el soporte de conector de batería a la placa lógica:
    • Remueve los dos tornillos Phillips que sujetan el soporte de conector de batería a la placa lógica:

    • Un tornillo de 2.9 mm

    • Un tornillo de 2.3 mm

    • A lo largo de esta guía, mantén un registro cuidadoso de tus tornillos para que cada uno vuelva a su lugar durante el re-ensamblaje Instalar un tornillo en el lugar equivocado puede causar daños permanentes.

    FYI - I used some blue painters tape wrapped around a piece of cardboard to hold the screws and brackets in place, in order, so they did not get lost. Some of those screws are MICROSCOPIC so be careful!

    I also suggest having very good lighting, even a camping headlight for hands-free well lit work space. You will thank me later :-)

    Julie Sanchez - Contestar

    Use the bit labeled “PH000”.

    Joe Teichert - Contestar

    PH000 bit just wants to free-spin in the 2.3 mm screw. no bite in the head at all. had no difficulty removing the 2.9 mm screw with the same Phillips. had to abandon battery replacement effort.

    Benjamin Stalcup - Contestar

    For this part, neither PH000 or Y000 worked. Technically, it’ll set you back 31$ because you will need the PH00 screwdriver for this part, and the part where you need to open the screen. They have ph00 screwdrivers in every hardware store and even ifixit.com. just know that they put the wrong screwheads for you

    Jack Daniel - Contestar

    Do not lose track of which hole these screws go into. They MUST be put back into the correct hole that they came out of. If not, you will get the dreaded “long screw damage” on the mainboard, and that will be the end of the show.

    Just remember where these screws go, and it will be fine.

    Harry McDow - Contestar

    This step is extremely important in fixing your phone: I had an iPhone that I fried as I forgot to disconnect the battery, end of the show!

    Jaron Foo - Contestar

    Ended up employing a Philips #0 from a regular jeweler/precision kit on the 2.3mm screw. Bits seem a bit off for this step.

    Vance Bell - Contestar

  13. Remueve el soporte de conector de batería. Remueve el soporte de conector de batería.
    • Remueve el soporte de conector de batería.

    Does it matter if the brackets arent put back in the phone? I bought a used phone and brackets are missing. Thanks!

    Coupon Crazy - Contestar

  14. Usa un spudger o una uña limpia para desconectar el conector de la batería haciendo palanca hacia arriba de la placa lógica. Usa un spudger o una uña limpia para desconectar el conector de la batería haciendo palanca hacia arriba de la placa lógica. Usa un spudger o una uña limpia para desconectar el conector de la batería haciendo palanca hacia arriba de la placa lógica.
    • Usa un spudger o una uña limpia para desconectar el conector de la batería haciendo palanca hacia arriba de la placa lógica.

  15. Dobla el conector hacia atrás para asegurarte de que no haga contacto y encienda el iPhone mientras trabajas en él. Dobla el conector hacia atrás para asegurarte de que no haga contacto y encienda el iPhone mientras trabajas en él. Dobla el conector hacia atrás para asegurarte de que no haga contacto y encienda el iPhone mientras trabajas en él.
    • Dobla el conector hacia atrás para asegurarte de que no haga contacto y encienda el iPhone mientras trabajas en él.

    When putting the new battery in, make sure to line up the plug and not to the top of the battery… our battery was smaller so the plug would NOT have lined up if we used the top of the battery. ALSO, the plug was NOT 90 degrees so we had to finagle the plug. Also, make sure there is a clear CLICK when you plug in the connector or it may not work. Ours went in but guess didn’t go far enough so we had to take the screen off and push it harder until we heard the “click” then it worked fine.

    Won Hong - Contestar

  16. Remueve los siguientes tornillos Phillips :
    • Remueve los siguientes tornillos Phillips :

    • Tres tornillos de 1.3 mm

    • Un tornillo de 1.6 mm

    • Un tornillo de 3.0 mm

    • Durante el reensamblaje, es fundamental colocar este tornillo de 3.0 mm en la esquina superior derecha del soporte. Colocarlo en otro lugar puede dañar la placa lógica.

    I really don't see value in removing screen use box and rubber band keep at 90 degrees.

    John Parker - Contestar

    I leave screen on as well for this. - Tho I prefer a 45 degree lean.

    Thor -

    I just changed my battery and also left the screen attached. I was lucky enough to get all 3 adhesive battery strips out clean so I didn’t have a struggle with the battery coming out. If I was going to need to get rough with it I was going to take the screen off at that point.

    Michael Gross - Contestar

    To keep track of screws, draw a quick outline of the display cable bracket/cover, with five dots where screws should be. Drop the screws on the corresponding dot. Helps if you use magnet pad.

    Christa - Contestar

    Better yet, print out the pictures from the iFixit website, and use clear tape (“Scotch tape”) to TAPE the screws onto the place in the picture where they belong.

    Tom -

    Which screwdriver from the kit do I use for which screw?

    Shiva Sharma - Contestar

    I made a mistake and unscrewed the screw just north north west of the one circled in yellow. Of course I lost the screw. Can anyone give me any guidance about this? what does the wire connected to it do? What is the size of the screw, in case I have to replace it?

    P.S. This is another reason to consider the possibility of NOT removing the screen just to replace the battery: removing the screen presents a additional possible headache, especially for people like me with bad eyesight who probably shouldn’t be doing this in the first place.

    Tom - Contestar

    I didn’t think this was necessary, bit I see it relieves stress on the front-facing camera and sensor cable connector; I did not disconnect the display connector nor remove the display screen.

    Lou Fazio - Contestar

    This step of separating the two parts of the phone deserves careful consideration. In my case, I had propped up the display assembly with a box and rubber bands. However, only 2 of the battery adhesive strips came off easily. The effort to remove the battery with the display assembly attached was not a good move on my part. I jarred the ear speaker cable and after reassembly I had no camera or working ear speaker. Taking off these 5 screws and removing the three cables is not difficult. My suggestion: is you have ANY trouble removing the 3 battery adhesive strips, STOP, separate the two components, and then continue with the battery removal. Don’t struggle removing the battery with the display assembly attached. (I replaced the ear speaker cable, and all is working now)

    Richard Perl - Contestar

    Thanks for this tip! I am having a really hard time removing this plate because one of the screw heads are stripped. So I’ll try removing the battery adhesive strips first to see if I can get the battery out without removing the screen.

    nathanfunk -

    Use dixie cups and label them for each part you take out. You can stack the dixie cups to keep them in order.

    Bradley Nolen - Contestar

  17. Remueve el soporte del cable de pantalla. Remueve el soporte del cable de pantalla.
    • Remueve el soporte del cable de pantalla.

  18. Ten cuidado de solo levantar el conector y no el zócalo de la placa lógica. Usa una herramienta de apertura de plástico para desconectar la cámara frontal y el conector del cable del sensor.
    • Ten cuidado de solo levantar el conector y no el zócalo de la placa lógica.

    • Usa una herramienta de apertura de plástico para desconectar la cámara frontal y el conector del cable del sensor.

    FYI, in the video she uses the spudger for this but I think either one will work.

    Julie Sanchez - Contestar

    I found prying from the right to be better

    Lou Fazio - Contestar

    Is there any need for this step if only the Battery is replaced

    mrrreid - Contestar

    I don’t recommend using the spudger for this as you can do more damage that way. I scratched the black square thing underneath.

    Laura Houghton - Contestar

  19. Usa una herramienta de apertura de plástico para desconectar el cable del digitalizador y  sacarlo de su zócalo en la placa lógica Cuando vuelvas a conectar el cable del digitalizador, no presiones el centro del conector. Presiona un extremo del conector, luego presiona el extremo opuesto. Presionar en el centro del conector puede doblar el componente y causar daños al digitalizador.
    • Usa una herramienta de apertura de plástico para desconectar el cable del digitalizador y sacarlo de su zócalo en la placa lógica

    • Cuando vuelvas a conectar el cable del digitalizador, no presiones el centro del conector. Presiona un extremo del conector, luego presiona el extremo opuesto. Presionar en el centro del conector puede doblar el componente y causar daños al digitalizador.

    Thanks you i fix it

    God Hand - Contestar

    “When reconnecting the digitizer cable, do not press the center of the connector. Press one end of the connector, then press the opposite end. Pressing in the center of the connector can bend the component and cause digitizer damage. “

    The following note above was so helpful. I was speeding through the process of getting things back together, since it seemed easy to connect the digitizer cable, but I kept pushing it in the middle and I wouldn’t connect. Until I read through this step and realized it was easier if I would’ve connected one side and then the opposite side right after.

    Jeffrey Robinos - Contestar

    Don’t be too shy when pushing the ends of the digitizer connector back to place. If it does not connect properly, you might face the “half backlight” problem, even if you did not kill any LCD filter. Also check carefully, that you don’t clamp parts of the sticky sealing material placed around the connector inside the connection area.

    Norbert Andreas Richartz - Contestar

    This part was a very frustrating experience for me.  I thought that my replacement screen was just poor quality, as it worked when it wanted to work.  Pressing home/power repeatedly sometimes brought it back, charging to 100% also brought it back.    The actual problem was that it is very easy to get some of the gasket material caught in the connector, which I couldn’t see until I used my jeweler's loupe.  I used 91% alcohol to carefully clean all of this off until all pins were shiny, and it took about 6 tries to get it right.  However, the screen’s been running well for 2 days now.  I already bought another screen replacement which I have for a spare as it was 100% not the problem.

    chumblyf - Contestar

    I followed all the steps, so the sound is missed. What could be happened? thanks a lot. Fabio Balbino

    Fabio Balbino - Contestar

  20. Asegúrate de que la batería está desconectada antes de desconectar o reconectar el cable en este paso. Desconectar el cable de pantalla levantándolo de su zócalo en la placa lógica.
    • Asegúrate de que la batería está desconectada antes de desconectar o reconectar el cable en este paso.

    • Desconectar el cable de pantalla levantándolo de su zócalo en la placa lógica.

    How much is this to replace?

    Alistair knight - Contestar

    And where could I buy from?

    Alistair knight - Contestar

    After finishing the assembly I got the message “Touch ID cannot be enabled on this phone”. I found this connector was loose. Plugged it back in and that fixed it.

    Bryan Province - Contestar

    Always make sure to disconnect the battery before you do any work on the phone replacing any parts the digitizer or anything. And before you start make sure the phone is turned off you don’t want any power surges. If you also have a static electricity bracelet that also is a plus to use but isn’t a necessity just a nice piece of mind. Some cases you do need to use one so you don’t discharge static electricity to an electrical component and mess it up.

    Brent - Contestar

    Be very careful in this step. I noticed it’s very easy to tear the flex when trying to lift it out of its socket from the right side.

    shoeib - Contestar

    What is the cable and how is it connected/fixed to the motherboard between the bottom socket and the screw hole.

    Mine came loose somehow?

    Jason Engelsman - Contestar

    I figured out my own question its the Wi-Fi diversity antenna cable. But how is it connected/secured to the motherboard?

    Jason Engelsman - Contestar

    i pressed on the center of the digitizer connection. and the bottom half of my screen didnt work. i then took that same front panel assembly and tried to install it on another old iphone 6s+ and i had the same issue.

    can i still fix it?

    what exactly is broken now?

    alejandro rueda - Contestar

    @mynameisoli Honestly this just sounds like a defective screen to me, but it’s hard to say for sure. Look closely at the connector at the end of the ribbon cable and check it for damage. If it’s slightly bent/curved, all the pins won’t make good contact in the socket. You can try bending it back so it lays flat, but you have to be very careful not to damage the connector or contaminate the pins with skin oils, so it’s tricky—and it may be harder to return as “defective” if you mess up the connector. So try this at your own risk. Apart from that, I would just return it and try a different display. Good luck!

    Jeff Suovanen -

    The 6s plus screen repair kit i bought has the wrong size cable here on the replacement part. SOL.

    Alex Richardson - Contestar

    Once I accidentally disconnected the display assembly cables before disconnecting the battery. Now the home button and fingerprint sensor doesn’t work. Any solution to this?? I have tried a different home button, even that doesn’t work.

    a3roar - Contestar

  21. Remueva el ensamblaje de pantalla. Durante el reensamblaje, deténte aquí si deseas para reemplazar el adhesivo  alrededor de los bordes de pantalla.

    For instructions on home button swap out to the new screen you just installed, go here

    Reemplazo del ensamblaje del botón de inicio del iPhone 6s Plus

    Superior Office Systems - Contestar

    Do you know whether the adhesive contributes to waterproofing, or just for stability/adhesion?

    Christa - Contestar

    @kitabel The iPhone 6s case isn’t waterproof, so I don’t think adhesive around the display is contributing anything other than stability. The 6s series does have some water resistance, but it’s mostly internal and not something Apple advertises.

    Jeff Suovanen -

    If you have a replacement adhesive for the display, you may need to install it before reconnecting cables to the components. If the adhesive wraps all the way around the display, it will be impossible to install it once the display is reconnected.

    Matthew Olwell - Contestar

    These instructions worked great for me. Thank you!

    Chris Enloe - Contestar

  22. Remueve los dos tornillos de 1.9 mm Phillips que sujetan el soporte de botón de inicio.
    • Remueve los dos tornillos de 1.9 mm Phillips que sujetan el soporte de botón de inicio.

    Maybe this should be totally obvious, but it took me a minute or two to realize that this step is performed on the DISPLAY ASSEMBLY that was just removed, rather than the main body of the phone, which is the part on which all the previous steps were performed.

    Tom - Contestar

    The new display came with a 1.9mm screw installed (the top left one above). This must be removed before putting back the home button bracket. It took me way too long to realize why I couldn’t thread the old screw back into the hole.

    Brandon Mathew - Contestar

    If you bought a screen assembly with a home button but have not ever set up touch ID can you set up touch ID on the new screen’s home button?

    Andrew Shircel - Contestar

    The home button and logic board are usually married. So if it’s a new home button paired with the original logic board, the Touch ID won’t work.

    Brittni Gange -

  23. Remueve el soporte de botón de inicio. Remueve el soporte de botón de inicio.
    • Remueve el soporte de botón de inicio.

    My home is wiggley I do not like it

    can you put home button adhesive

    Riley - Contestar

  24. Usa la punta afilada de un spudger para desconectar el cable de botón de inicio de su conector en el ensamblaje de la pantalla Usa la punta afilada de un spudger para desconectar el cable de botón de inicio de su conector en el ensamblaje de la pantalla
    • Usa la punta afilada de un spudger para desconectar el cable de botón de inicio de su conector en el ensamblaje de la pantalla

    Gently: this piece is attached to the plastic cabling, not the surface of the phone

    Christa - Contestar

    Buongiorno,ho cambiato display però adesso non mi funziona touch sul tasto home…cosa potrebbe essere???grazie

    eduartkurani - Contestar

    ciao, hai risolto? ho sto valutando se cambiare lo schermo appunto per questo motivo, ho letto online che gli schermi non originali danno questo problema

    serena184 -

  25. Con la punta del dedo, presiona suavemente hacia arriba el botón de inicio en la parte frontal del ensamblaje de la pantalla para separar lentamente la junta de goma del botón de inicio del panel frontal. La junta es muy delgada y se rompe fácilmente. Aplica presión constante y dale tiempo para separarse.
    • Con la punta del dedo, presiona suavemente hacia arriba el botón de inicio en la parte frontal del ensamblaje de la pantalla para separar lentamente la junta de goma del botón de inicio del panel frontal.

    • La junta es muy delgada y se rompe fácilmente. Aplica presión constante y dale tiempo para separarse.

    “The gasket is very thin and will tear easily. Apply steady pressure and give it time to separate. “

    The note above was very helpful. It really is thin and for one second I thought I punctured a whole through it, so be careful.

    Jeffrey Robinos - Contestar

    I did this on 2 separate phones. The first time, I did it according to directions, and it worked well. However, the adhesive pulled off in the process. On the 2nd phone I used a handwarmer to slightly warm the home button area. (I think an iOpener would work best, but I didn’t have one on hand). With the constant pressure after being heated, the home button assembly came off easily, and the adhesive stayed in place. I’ll definitely use slight heat in the future for this step as it seems to lessen the possibility of damaging the assembly.

    Jami - Contestar

    I would have liked to see the heating instructions on this page. I only saw it once I re-watched the video as I was having trouble getting the button out. iFixit would have made another sale had it been obvious that the heating pad would come in handy. I ended up using a microwave heating pad instead. Worked fine.

    Scott - Contestar

    If anyone else is totally caught off guard by the need for heat at this point, the previous mention of a heating pad gave me the idea of heating a wet paper towel in the microwave and sticking it in a plastic bag. Obviously make sure no moisture escapes into the device. Worked fine, and is absolutely necessary: that gasket is VERY delicate.

    Joshua Rodgers - Contestar

  26. Usa el extremo puntiagudo de un spudger para levantar el cable flexible del botón de inicio ligeramente adherido del ensamblaje de pantalla. Usa el extremo puntiagudo de un spudger para levantar el cable flexible del botón de inicio ligeramente adherido del ensamblaje de pantalla. Usa el extremo puntiagudo de un spudger para levantar el cable flexible del botón de inicio ligeramente adherido del ensamblaje de pantalla.
    • Usa el extremo puntiagudo de un spudger para levantar el cable flexible del botón de inicio ligeramente adherido del ensamblaje de pantalla.

  27. Remueve el ensamblaje del botón de inicio. Remueve el ensamblaje del botón de inicio.
    • Remueve el ensamblaje del botón de inicio.

    Make sure you remove any broken glass from around the button edges. Took me a few times to realize it had some glass on it.

    johnarchitzel - Contestar

    I could not believe how EASY this was to repair my phone! Granted, it took me awhile (2 hrs) to replace a camera and a screen, but I was probably overly meticulous about each step, especially making sure the old adhesive was fully removed and the frame was clean. I can imagine, with tolerances being as tight as they are — I could barely see some of the screws! — the slightest lump of glue might have made a smooth placement difficult. But, in the end, it was worth it! Screen looks and works awesome, and so does my camera!

    Huge props to you for this detailed guide! Very easy to follow and flawless result! Thank you!

    Patrick Lynch - Contestar

    does the home button work after you put it on the new repaired phone?

    Victoria Vojvodich - Contestar

    what about the camera? i don’t see the step moving the old camera over to the new screen

    Brian - Contestar

Conclusión

Para volver a ensamblar tu dispositivo, sigue estas instrucciones en orden inverso.

62 personas más completaron esta guía.

Un agradecimiento especial a estos traductores:

90%

¡ Mariana nos está ayudando a reparar el mundo! ¿Quieres contribuir?
Empezar a traducir ›

Evan Noronha

Miembro Desde 05/02/15

198,454 Reputación

178 Guías creadas

Equipo

iFixit Miembro de iFixit

Community

132 Miembros

13,037 Guías creadas

I swear a night time operation for a home button transfer was not easy! But... I pulled it off!

SerJay - Contestar

Which part is difficult?

yinliangdl -

The only problem I experienced was that you have to re-use the black gasket around the home button. It was tricky to have to place it on the new home button, but I got it after a few tries.

Noah Donovan - Contestar

can i still use the finger print scanner after changing the home button?

Ej Villar - Contestar

No, the fingerprint scanner and logic board are paired during their manufacturing so if the original scanner is destroyed, you will never have Touch ID again. But you should regain the functionality of the button.

Dakota Martin -

Thanks for the guide. Had to switch over here from the screen assembly guide, as it did not include home button, and vice versa. But done, success, happy.

Christa - Contestar

Does the fingerprint scanner still work with aftermarket home button?

Jerone Manley - Contestar

Hi! I accidentally ripped the cable that you can see clearly on the display assembly on atleast the two last steps. What i mean is the black cable that is coming from the LCD and which you connect the home-button to.

Is that replacable or am i gonna live without a home-button? Thanks in advance.

vitportion - Contestar

I have a destroyed iPhone 6s Plus and it is DESTROYED found it on the street with no screen so thanks

Alberta momenta - Contestar

im having an issue i replaced the home button with an oem replacement and new gasket. when i reinstall the bracket screwed all the way the button wont click its against the bracket. i loosen the screws a little which helped but then closing the phone i get the same issue.

adamshamblin1974 - Contestar

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 19

Ultimos 7 días: 116

Ultimos 30 días: 588

Todo El Tiempo: 38,286