Introducción
Usa esta guía para reemplazar la pantalla y el digitalizador en tu Huawei Mate 10 Pro.
Se dañará el sello impermeable del dispositivo al abrir el Mate 10 Pro. Si no reemplazas los sellos adhesivos, tu teléfono funcionará normalmente, pero perderá su protección contra el agua.
Antes de desmontar el teléfono, "descargue la batería por debajo del 25%". La batería puede incendiarse y/o explotar si se perfora accidentalmente, pero las posibilidades de que eso ocurra son mucho menores si se descarga.
Qué necesitas
-
-
Apaga tu teléfono.
-
Prepara un iOpener y aplícalo a la parte trasera del teléfono durante alrededor de dos minutos para aflojar el adhesivo por debajo de la tapa trasera.
-
-
-
Levanta la tapa trasera con una ventosa hasta que puedas insertar el extremo plano de un spudger halberd.
-
Usa un spudger halberd para cortar el adhesivo por debajo de la tapa trasera en todos lados del teléfono.
Faire attention à ne pas enfoncer trop le cutter/spatule hallebarde. Surtout à l’approche des boutons ON/OFF et volume, la nappe ne passe pas loin et se branche à coté de l’empreinte digitale.
Bilan, j’ai coupé cette nappe et n’ai plus de bouton volume et on/off.
Plus qu’à chercher la piece de rechange pendant que le telephone est ouvert ;)
I found it easiest to insert the first pick on the side of the phone, not the top as shown in the pictures. The side is slightly more flexible than the ends because it is longer.
-
-
-
Voltea la tapa trasera hacia un lado.
-
Retira el tornillo Phillips #00 que sujeta el escudo metálico, sentado encima de la conexión del cable del sensor de huellas digitales.
When re-assembling, you can test the phone before putting the covers back on. If you test it before you connect the fingerprint reader then you need to re-start the phone before the fingerprint reader will work.
-
-
-
Remueve los doce tornillos Phillips #00.
-
Con cuidado remueve los escudos en la parte superior de la placa madre y la placa de carga.
When re-assembling, you can test the phone before putting the covers back on. However, if you test it before you fit the top inner cover (the one in the middle picture above) the speaker will not work.
The top and bottom inner covers both have tiny flanges which you need to insert into slots in the outside edge of the phone before you drop the rest of the cover into place. If you don't put the flanges in first the covers will not fit properly.
-
-
-
-
Usa un spudger para desconectar el cable flexible del puerto de carga de la placa madre y de la placa hija.
-
-
-
Usa un par de pinzar para remover con cuidado el puerto de carga con su cable flexible.
Do I need to apply a new sealer / adhesive tape in order to assemble the phone back together? If yes, where can this be purchased for Huawei Mate 10 Pro?
If the adhesive on the back cover is damaged too much and/or doesn’t stick any more it is recommended to remove the old adhesive from the back cover and clean off any residue with isopropyl alcohol (>90%). Then use thin double sided adhesive tape and apply new strips of adhesive.
Hi David,
opening the Mate 10 Pro will damage the waterproof sealing on the device. If you do not replace the adhesive seals, your phone will function normally, but will loose its water-protection.
Hi there, I completed the battery replacement nicely with all your steps, the phone could turn on and function normally, the only issue after the battery replacement is the phone has no sound and vibration. I have ensure all connectors are back to place securely. Does anyone have any clue of the cause of no sound and no vibration?
-
-
-
Usa un spudger para desconectar el cable flexible de la batería.
-
Aplica un iOpener en la pantalla durante al menos un minuto para aflojar el adhesivo debajo de la batería.
Hier auf KEINEN Fall ein Werkzeug aus Metall (wie den iSesame) verwenden!
Die Funken die dabei sprühen sollten sehr klar machen, daß das keine Gute Idee für den Akku ist. XD
-
-
-
Utiliza un spudger para levantar la batería y deslizarlo a lo largo del lado para separar el adhesivo.
-
Remueve la batería.
I left the phone on top of a hot-water bottle all the way through the dismantling, right from the start. That way, the phone was nice and warm and the battery came out fairly easily. There is a slightly wider gap in the housing, just where the spudger is being inserted in the first picture above, which makes the job easy.
-
-
-
Utiliza un spudger para desconectar el cable flexible de la pantalla.
-
Prepara un iOpener y aplícalo a la pantalla durante al menos dos minutos para aflojar el adhesivo que se encuentra debajo. Cuidar especialmente la parte superior e inferior.
-
Si tu pantalla está rota o agrietada, protege tus ojos de los fragmentos de vidrio, aplica un poco de cinta adhesiva transparente en la pantalla para tener un mejor agarre para abrir el teléfono.
-
-
-
Empuja un spudger contra la parte posterior de la pantalla a través del recorte en el marco central, donde se encontraba el puerto de carga, para crear un espacio entre la pantalla y el marco.
-
Inserta la punta de una púa de apertura en el hueco que acabas de crear.
Der Kleber löst sich erst bei 90°C!!
(Quelle: Herstellerangaben zu ähnlichen Klebern, z.B. den bekannten T-8000 und T-7000.)
Daher ist es so problematisch mit gewöhnlichen Warmkompressen bzw dem iOpener! Da diese nur bis 100° warm werden können, und schnell auf unter 90°C abkühlen! Deswegen ist es so schwer! Und deswegen geht der Bildschirm so leicht kaputt!
Wenn ihr also die Möglichkeit habt, versucht, das Ding auf ausreichend weit über 90° zu erhitzen, aber das so kurz und so niedrig wie möglich zu halten, da der Rest des Geräts bei den Temperaturen sonst auch leicht Schaden nehmen kann!
Also z.B auf 99°C erhitzen (mit einem Bratenthermometer zwischen Wärmequelle und Bildschirm leicht festzustellen), die Wärmequelle überall außer an einer Stelle weiter auf dem Bildschirm belassen(!), und dann eilig aber vorsichtig, den Kleber an der freien Stelle (Ladebuchse) lösen, und sich so voranarbeiten.
-
-
-
Después de cortar el adhesivo por todos los lados del teléfono, voltea la púa de apertura para levantar la pantalla.
-
Es posible que el cable de la pantalla todavía se pegue un poco al marco medio. En este caso, afloja con cuidado y enróscalo a través del hueco en el marco.
-
Remueve la pantalla.
-
Si es posible, enciende tu teléfono y prueba tu reparación antes de instalar el nuevo adhesivo y volver a sellar el teléfono.
Si el marco está doblado, o si quedan restos de pegamento o vidrio, la nueva pantalla no se montará correctamente y puede dañarse. Si es necesario, reemplaza el marco.
La mejor forma de asegurar la nueva pantalla es con una hoja de cinta adhesiva de doble cara cortada a medida. Aplica la cinta en la parte posterior de la pantalla y, a continuación, pasa con cuidado el cable de la pantalla a través del marco. Alinea la pantalla y presiónala en su lugar.
Para volver a montar el dispositivo, sigue estas instrucciones en orden inverso.
Si es posible, enciende tu teléfono y prueba tu reparación antes de instalar el nuevo adhesivo y volver a sellar el teléfono.
Si el marco está doblado, o si quedan restos de pegamento o vidrio, la nueva pantalla no se montará correctamente y puede dañarse. Si es necesario, reemplaza el marco.
La mejor forma de asegurar la nueva pantalla es con una hoja de cinta adhesiva de doble cara cortada a medida. Aplica la cinta en la parte posterior de la pantalla y, a continuación, pasa con cuidado el cable de la pantalla a través del marco. Alinea la pantalla y presiónala en su lugar.
Para volver a montar el dispositivo, sigue estas instrucciones en orden inverso.
Cancelar: No complete esta guía.
18 personas más completaron esta guía.
Un agradecimiento especial a estos traductores:
100%
Estos traductores nos están ayudando a reparar el mundo! ¿Quieres contribuir?
Empezar a traducir ›
2 comentarios
Nicely written guide, I am curious about trying this myself in the near future. I have sadly got a tiny scratch in my screen in the last couple days where I haven’t had a screen protector on! Very frustrating.
I’ve replaced almost everything for an iPhone 6+ and done a complete teardown. How difficult is this repair compared to something like that?
Perfect tutorial, my only problem was doing it without an opener was difficult. I don’t know if this kind of comment is allowed, and it it isn’t, please just edit this part instead of taking down the whole comment. An icepack in the microwave worked VERY well for me in the end.
That said, breaking the screen to take it off was VERY hurtful in my soul.
Thanks for the instructions!!!
Erm… Simply impossible to open the phone this way…
I used the iOpener for 2 mins as instructed, I’ve used even an hair drier for 30 secs on max power (could barely touch the phone after) and still with the suction tool I was not able to open the phone.
It simply doesn’t budge!!!
Miguel Oliveira - Contestar
This was much easier than I expected! ;-)
I put the phone on a hot-water bottle for about 5 minutes. I put the first pick in the side of the phone, not the top as shown in the next section. Then I kept the phone on the hot water bottle through all the following steps so that the battery glue was nice and warm when it came to that section.
Oliver Moffatt - Contestar