Saltar al contenido principal

Introducción

Sigue los pasos de esta guía para quitar o reemplazar los tornillos Pentalobe en un iPhone 7.

  1. Antes de comenzar, descarga la batería de tu iPhone por debajo del 25%. Una batería de iones de litio cargada puede incendiarse y / o explotar si se perfora accidentalmente.
    • Antes de comenzar, descarga la batería de tu iPhone por debajo del 25%. Una batería de iones de litio cargada puede incendiarse y / o explotar si se perfora accidentalmente.

    • Apaga tu iPhone antes de comenzar el desmontaje.

    • Remueve los dos tornillos pentalobe de 3.4 mm en el borde inferior del iPhone.

    • Abrir la pantalla del iPhone dañará sus sellos impermeables. Ten sellos de reemplazo listos antes de seguir con el próximo paso o ten cuidado de evitar la entrada de líquidos si vuelves a ensamblar tu iPhone sin reemplazar los sellos.

    Can anyone confirm 7/7P's pentalobe screws have a ring of seal near the screw head?

    Cooper Chase - Contestar

    Confirmed, the screws have a black ring seal around the head.

    rcheing - Contestar

    Can’t get the display front

    Bernadette Pfeifer - Contestar

    From personal experience, I highly recommend before doing this procedure or any other, that you do a backup of your phone (preferably local) in case your procedure goes south.

    ballina5ny - Contestar

    I purchased the repair tools with the replacement battery from iFixit. The tools include a screw driver and three heads none were labeled 3.4 mm. I think the one that fit the pentalobe screws was labeled Y000. The guide should identify the screw driver head supplied by the kit not 3.4mm.

    Mark Lieberman - Contestar

    in the iphone 7 replacement battery kit from iFixit, the screwdriver that fits the 3.4 mm pentalobe screws is labeled P2 (and not Y000)

    Jan-Tijn Oppermann -

    the screwdriver PH000 does not work i wasted two screws and now they dont have the 4 cross mark they are now a circle, i buyed it all from Paraguay and it doesnt work, had to assembly back the parts because i got stuck like i mention with some screws, well im just going to send to a professional to install, thanks

    Martin Frutos, Nuñez - Contestar

    The bottom screws are Pentalobe, not Phillips.

    Bram Driesen -

    Before starting, I would recommend backing up your Iphone’s data just in case.

    Jon Moylan - Contestar

    If you managed to make it to this section, just send the phone into apple for 50 + 6 dollars shipping. The ribbon cables on the screen are designed to break. I can literally twist on the rest of the cable and it won’t fall apart but there is a diagonal section where it snaps. This is the fault of apple and the fault of ifixit for misrepresenting the fragility of the cables.

    Ryan Huebert - Contestar

    Had to reheat it a few times for a minute each with a hairdryer to get the seal to break after pulling and rocking the suction

    Cynthia Lamb - Contestar

    I’m technically challenged. Is there a premier national service who can professionally install a replacement battery got my 7 +?

    Richard - Contestar

    Do the screws come out in total?

    YVES THEUGELS - Contestar

    Is it the P2 you should use for the bottom??

    YVES THEUGELS - Contestar

    I heated the bottom of the phone with a hairdryer and then used a syringe to put a couple of drops of acetone directly into the bottom two screw holes. I GENTLY pulled on the screen with the suction cup and used the pry tool to GENTLY separate the screen. The sealant is applied around the entire display so be very careful pulling it off so you don’t break the fragile display cables.

    Anthony Scaminaci - Contestar

Conclusión

Error

Enlace de servicio de video no reconocido.

Example:

[video|http://vimeo.com/1234] or [video|http://vimeo.com/1234]Optional Caption[/video]

Current text:

[video|http://]
Para volver a montar tu dispositivo, sigue estas instrucciones en orden inverso.

45 personas más completaron esta guía.

Un agradecimiento especial a estos traductores:

en es

100%

Estos traductores nos están ayudando a reparar el mundo! ¿Quieres contribuir?
Empezar a traducir ›

Evan Noronha

Miembro Desde 05/02/15

209,608 Reputación

178 Guías creadas

Equipo

iFixit Miembro de iFixit

Community

140 Miembros

17,046 Guías creadas

3 comentarios

are there any water seals associated with the pentalobe screws? I blew compressed air into my iphone 7 and two tiny square rubber gaskets (~3mm) popped out. They squares have a round hole in them. I can only figure they are part of the pentalobe screw water seals, but I’m not sure, and I don’t know how to put them back in the phone to restore the water seal. Can anyone offer a solution?

Austin Taterka - Contestar

@ataterka The screws themselves have a tiny ring-shaped rubber gasket on them. The two rubber squares you found slip onto the screw bosses. I don’t think those are needed for water sealing, and they’re not even included on newer models.

Jeff Suovanen -

Does iPhone 7 and iPhone 8 (including «Plus» models) share the same bottom pentelope screws?

Victor Rezai - Contestar

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 16

Ultimos 7 días: 72

Ultimos 30 días: 311

Todo El Tiempo: 30,304