Saltar al contenido principal

Repara tus cosas

Derecho a reparar

Tienda

Introducción

Sigue esta Guía para remover o reemplazar los tornillos Pentalobe de un iPhone 6s

  1. Antes de desarmar su iPhone, descarga la batería por debajo del 25%. Una batería de litio-ion cargada puede generar fuego o explotar si es perforada accidentalmente.
    • Antes de desarmar su iPhone, descarga la batería por debajo del 25%. Una batería de litio-ion cargada puede generar fuego o explotar si es perforada accidentalmente.

    • Apaga tu iPhone antes de empezar a desarmar.

    • Remueve los dos tornillos Pentalobe P2 de 3.4 mm que se encuentran cerca del conector Lightning en el borde inferior de su iPhone.

    Hi, just got the repair kit that came with IPhone 6S battery. I felt that there’s no explanation on which tool to use to remove the two 3.4mm P2 Pentalobe screws. It’s not helpful just to say “Remove the two 3.4 mm P2 Pentalobe screws on the bottom edge of the iPhone, next to the Lightning connector. “. It’s more important to explain how and what tool to use. The repair tool kit tools were not marked at all and it’s not right to assume that people know which tool or part to use. Please kindly address this issue. Thanks. Janet

    Janet Monaghen - Contestar

    @beingchen For the P2 pentalobe screws you should use the driver bit marked P2. Might be a little hard to see but it’s there, etched into the side of the bit.

    Jeff Suovanen -

    It’s very clear which tool you need. As it says these are “3.4 mm P2 Pentalobe screws” - so you need a 3.4 mm P2 Pentalobe screwdriver…

    alexanderbrix1987 - Contestar

    Just a P2 driver—3.4 mm is the length of the screw.

    Jeff Suovanen -

    If you can’t identify which screwdriver in the kit to use, you probably shouldn’t be working on your phone. Just sayin’

    Keith Hockenbeck - Contestar

    Is it ok to replace the battery if the phone screen is broken?

    Reem - Contestar

    Of course! As long as the screen and battery are disconnected from the motherboard, you can replace anything!

    Charles Bejarano -

    is it possible to change my battery on my iphone 6s and use a battery that has been already used in another 6s

    morgan durnford - Contestar

    Yeah it would work, but if the battery heath on the 2nd battery is bad, just get a new one.

    Charles Bejarano -

    @moe6802 Removing the battery can damage it, and it shouldn’t be used afterward. It may seem fine, but even minor battery damage can lead to a fire hazard. Not worth it for such a cheap part. If you need a battery, just get a new one.

    Jeff Suovanen -

    How do you discharge a battery? Do you just let the battery drain or is there something less time consuming that you can do?

    Matthew Petts - Contestar

    There is no easy way to discharge the battery in “less time”. Perhaps the fastest way is to play a visually-complex modern game or otherwise make your phone do a lot of work.

    Lance J -

    So my phone screen is completely black causing me to see nothing that is on my screen. And the battery is above 25%, near 100%. What do I do??

    Jessica I - Contestar

    you should post a question on the answers forum

    Max Li -

    you should post a question on the answers forum

    Max Li - Contestar

    I can’t the screws with the P2, seems that the screws are stuck, what can i do?

    Alberto Jabiles - Contestar

    My kit came with 3 screws. Are those to replace these 2 P2 screws? And what’s the third one for?

    Daniel Morse - Contestar

    If it came with 3 screws, then it’s an extra one just in case if a replacement screw gets lost.

    Charles Bejarano -

    My display is cracked/broken and not functioning. The slide bar doesn’t work. How do I shut down my phone?

    Timothy Huss - Contestar

    i have replaced several ipod batteries and laptop work, but these screws seem to loose but do not come out. how am i to remove them.shake the iphone?it seems the ioen is not in my kit, is that how to remove them?

    this seems idiotic but i remember some other system magnets that firt make your screws easier to keep, but this might be changed….any video? this seems 1st step blues!!!!

    makinfilms - Contestar

    never ind ishook it… is that in the guide?….iopener is not in the kit……never was before is this an upsell? do i skip it? i dont have it

    makinfilms - Contestar

    My screws aren’t coming out either. I’ve loosened them, but they aren’t coming out. I’ve shaken the phone, given it some slight bangs…nothing.

    Jesse Fisher -

    The following info is not given until step 21 in the instructions, and probably too late at that.

    DO NOT disconnect or reconnect any of the cables in this device until the battery itself has been disconnected!

    Don’t skip that step, intending to do it at the end, as you may damage the phone.

    ffissk - Contestar

    2 thoughts:

    1) Really? Steps 14-17 are about disconnecting the battery first, and step 17 notes “so it doesn’t get reconnected while you work.” How’d you get to step 21 and miss 14-17?

    2) These pages are user-editable. (Probably (hopefully) “curated” by iFixit staff.) You should add a warning to step 17 (or step 24).

    Bass Clef -

    NOW THAT YOU’VE REMOVED 2 SCREWS, and

    BEFORE YOU SNEEZE them into oblivion, or under the refrigerator (which is the same in many houses)

    MAY I suggest:

    1) Obtain:

    — a piece of paper, such as normal printer paper (not too much writing on one side)

    — a piece of tape, not too sticky, like masking tape (duct tape would be bad)

    ——— 1-1.5 inches (2.5-4 cm) wide

    ——— 6-8 inches (15-20 cm) long

    — a pencil (or pen)

    2) Put the paper on the side of your work area

    3) Lay the tape, sticky side up, on the paper

    4) Fold each end of the tape (~1 inch/2.5cm) back under itself, so the folded part faces the paper. Press the folded-back tape onto the paper

    You now have Sneeze & Wind Insurance for your tiny bits!

    5) Put the 2 pentalobes end down on the top end of the tape, next to each other. Push them a little onto the tape so they stick

    6) Use your pencil to note on the paper next to the screws: “1. Pentalobes”

    Now you may proceed with dissassembly, without worrying about telling the 1.5mm from the 1.6mm screws.

    or about sneezing!

    Bass Clef - Contestar

    My phone has a bad battery and a bad connector and I wasn’t able to get all of my photos before it died. Is there any chance I won’t lose them when I replace the battery? Or, is there any way to charge a 6s battery with a bad connector?

    Liz R - Contestar

    There is a great chance that photos, which are stored to flash memory, which is solid state memory, which is not affected when power is lost, will be there, right where you left them, once you restore power to your device. You could install a partially charged battery into your phone and then retrieve the important things, like your photos, if you don’t intend to continue using the phone. Else look at replacing the lightning connector assembly. Here: Reemplazo del ensamblaje del conector Lightning en iPhone 6s

    TimD -

    The P2 is not getting the screws loose at all. I have tried this several times and no budge on my iPhone 6s.

    Cassandra Vigil - Contestar

    To avoid to be screwed by lost or mixed screws:

    - Use magnetic pad, wipeable

    - Write the ifixit- steps next to the screws (maybe even with their sizes) and other bits removed

    with a non-permanent marker

    - When finished, simply wipe the pad, and it’s ready for the next repair

    Hope that helps.

    Ulrich Janßen - Contestar

  2. El kit de herramientas esencial

    Las herramientas más útiles en nuestro kit más compacto.

    Compra ahora

    El kit de herramientas esencial

    Las herramientas más útiles en nuestro kit más compacto.

    Compra ahora
Conclusión

Para volver a armar tu dispositivo, sigue estas instrucciones en orden inverso.

31 personas más completaron esta guía.

Un agradecimiento especial a estos traductores:

100%

Estos traductores nos están ayudando a reparar el mundo! ¿Quieres contribuir?
Empezar a traducir ›

Evan Noronha

Miembro Desde 05/02/15

200,450 Reputación

178 Guías creadas

Equipo

iFixit Miembro de iFixit

Community

131 Miembros

13,458 Guías creadas

I noticed both my pentalobe screws wouldn’t screw in last time. Upon checking the little components that the screws fix into were loose inside. Not a major drama but they also seem to hold the charger cable in place… or at least I’ve noticed cables are loose on my iPhone 6 since then. Is there a part I can buy to fix this issue, does anyone know please?

justingrisbrook - Contestar

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 8

Ultimos 7 días: 79

Ultimos 30 días: 275

Todo El Tiempo: 16,417