Saltar al contenido principal

Repara tus cosas

Derecho a reparar

Partes y herramientas

Introducción

Esta guía te mostrará los pasos necesarios para reemplazar una placa hija con puerto de cargo defectuosa o dañada en el Samsung Galaxy S6. Este componente incluye la toma de audio, el puerto de carga y los botones laterales.

Esta guía requiere remover el cristal trasero. Remover el cristal trasero destruye el adhesivo que lo sujeta en su lugar.

Sigue esta guía para volver a instalar el cristal trasero.

  1. Inserta un clip o herramienta de expulsión de SIM en el orificio de la ranura de la tarjeta SIM en la parte superior del teléfono No introduzcas la herramienta en el orificio del micrófono o podrías causar daño. Busca el contorno de la bandeja SIM. Presiona para expulsar la bandeja de la tarjeta SIM.
    • Inserta un clip o herramienta de expulsión de SIM en el orificio de la ranura de la tarjeta SIM en la parte superior del teléfono

    • No introduzcas la herramienta en el orificio del micrófono o podrías causar daño. Busca el contorno de la bandeja SIM.

    • Presiona para expulsar la bandeja de la tarjeta SIM.

    • Remueve la bandeja de la tarjeta SIM del teléfono.

    First thankful sir that you have a good idea for people to creat like this.. I am very happy from your website its too good. All things i learn from your website thank you..

    Lovely Khan - Contestar

  2. Te recomendamos que limpies tu microondas antes de continuar, ya que cualquier suciedad desagradable en la parte inferior puede terminar pegado a el iOpener. Coloca el iOpener en el centro del microondas.
    • Te recomendamos que limpies tu microondas antes de continuar, ya que cualquier suciedad desagradable en la parte inferior puede terminar pegado a el iOpener.

    • Coloca el iOpener en el centro del microondas.

    • Para microondas giratorios: Asegúrate de que la placa gira libremente. Si el iOpener se queda atascado, puede sobrecalentarse y quemarse.

    which temperature must be used for heating? Thx

    fbarletta - Contestar

    I found you need to be very patient when using the iOpener. It's worth taking your time, giving the heat time to work on the glue. When I finally got the battery out, there were some strips of glue left behind that I just cleaned off with some isopropanol before installing the new battery.

    By the way, I had to run the iOpener for longer in my microwave for it to get hot enough. When it was too hot to touch, I figured it was hot enough for the batteries.

    Fredrik -

    I didn't find this to be as hard as I had built it up in my mind to be; HOWEVER, saying that I need to say years ago I was the local Nokia service center in my town. But many years ago right after they got rid of analog times. Yeah. A classic installer/repairer mistake when starting something they haven't fixed or installed before is picking up the instructions, flipping through them; maybe even reading a section that is new-then tossing the instructions over the shoulder. "I got this." This usually comes right before something major gets broke. And I can tell you when you try to do it yourself and then mess it up horribly then take it to the repair shop. Well we called that "I can do it myself" syndrome and charged extra to put back together what they brought in in the box. Now knowing all this - I can't stress this enough because I am stupid, stupid, stupid. COVER YOUR SCREEN IN CLEAR BOXING TAPE AND READ ALL THE INSTRUCTION BELOW THROUGH TO THE END BEFORE EVEN ATTEMPTING THIS FIX. Take my advise.

    windizy - Contestar

    I didn't have an iOpener, so I used a wheat type heat bag. If you do this though, make sure you put a layer of plastic between your Mac and the bag, or you'll get condensation in places you don't want it.

    Martin Gray - Contestar

    I started out using the iOpener but switched to my wife's hairdryer. A heat gun or hair dryer proved to be much more convenient and is a time saviour. You can heat more and the glue becomes more fluid make the next steps with the opening picks much easier

    Jan Van Puymbroeck - Contestar

    I know this is obvious, but backup your iPad with iTunes before you start. I'd also turn off your passcode if you have one.

    Laurie Higgins - Contestar

    Ther first time you heat up the iOpener for this repair when its room temperature I had to heat it up for more than 30 seconds. I remember I had to heat it up for around 45 seconds. However, after that when you need to reheat it again during the repair 30 seconds will be enough.

    Yousef Ghalib - Contestar

    Not everybody has a microwave. You need to state how long and at what temperature in a conventional oven.

    Esmond Pitt - Contestar

    My microwave just died, can i heat it with boiled water?

    Alex COLOMBANI - Contestar

    Taping as shown is impractical when using hair dryer method—tape simply comes off in the heat and gets in way of getting out the shards on the sides. If the thing wasn’t shattered, then taping unnecessary.

    B. A. Computer Services - Contestar

    I used the wheat bag in a sensor microwave heating up to 65-70 deg C (155 def F).

    ian cheong - Contestar

    Get yourself a cherry pit bean bag the size of your iPad. Heat it, put the iPad on it for 3 to 5 minutes or so, reheat the cherry pit bean bag, again put your iPad on it. Then heat the iOpener and start working. The cherry pit bean bag will have to be reheated several times, but it will soften the adhesive so you have less problems with the iOpener

    Tim Feyaerts - Contestar

    The “Galaxy S8 Replacement Battery” that you are selling with the kit is the wrong battery, the one that you are selling is a 3000mAh (which is the wrong amperage) as the OEM Samsung Galaxy S8 battery is “Model #: EB-BG892ABA / 4000mAh / Normal Voltage: 3.85V / Charge Voltage: 4.4V / A/S: 1588-3366 4000mAh 15.0Wh

    stevengenat - Contestar

    The heating can be done very effectively (and quickly) with 3d printer heated bed. Make sure the bed is clean. Set the temperature to 60c, (130f ) and put the ipad face down for +/- 10 minutes. Repeat as needed throughout the “gentle prying” stages.

    polleyphony - Contestar

    The iOpener did not work at all for me.

    I had to use a heat gun and bring the edges of the case up to ~200 degrees (used an infrared thermometer to measure) before the glue would weaken. This obviously superheated the metal frame, so I also had to wear gloves to handle the phone while prying the back off with the included picks.

    Mike Jeanette - Contestar

    Repair instructions worked like a charm. Had to be patient with the iOpener and getting the screen off. I tried repeatedly without success until shifting the suction cup a bit to the left side where perhaps the glue had loosened up a bit more.

    Kyle - Contestar

    The iOpener, in my opinion, is of no help. Many warnings to say “don’t warm it too much”, but the glue doesn’t melt if not warm enough. As a result, a complete waste of time and energy. In addition, too much liquid in it, so it doesn’t lay on the device on a sufficient surface. I took a hairdryer and it worked much much better.

    laurentvidu - Contestar

    I’ve tried for 2 days and cannot get this to work. I should have just taken it to my local iphone fixit shop. This is a frustrating purchase to say the least.

    jeffrey hill - Contestar

    Step 1 should be: now that you have looked over the tools of this repair kit, take your ipad to the nearest repair store and let them handle it. Sure you will waste about $65 by purchasing this kit and the cost of the repair but you will not tear your ipad up and you will have at least 2 days of your life that you can spend time with your family.

    jeffrey hill - Contestar

    Just replaced the battery in my iPad mini LTE. Followed the Ifix step by step instructions and they worked very well. The only thing i would change is step 42. You do not have to lift the LCD connector from the logic board. So don’t. It’s an unnecessary step. Other then that all was good. It took me about 2 1/2 hours from start to finish but I took my time and I recommend you take your time also. Very exciting too finish doing it and see it come to life afterwards. Tested everything and everything still works

    Anybody want to buy my iFix battery replacement tool kit only used once cheap?

    kaplang - Contestar

    i opener sucks! it’s incapable of heating factory glue enough to take a sealed phone apart and caused my backglass to shatter. i removed it the rest of the way with a soldering iron!

    Elijah Marvin - Contestar

    You should, at least, mention which wattage is used for the 30 seconds heating - 750 isn’t enough, obviously. Display shatterered . Thanks.

    dr_baeschtlr - Contestar

    I used an immersion bath to heat this to 180F and applied it to the device until the outside temperature of the opener read 150F with an IR thermometer. Removing the screen took very little force with this method.

    breadandbits - Contestar

  3. Calienta el  iOpener durante treinta segundos.
    • Calienta el iOpener durante treinta segundos.

    • A lo largo del procedimiento de reparación, en cuanto el iOpener se enfríe, vuelve a calentarlo en el microondas treinta segundos más cada vez.

    • Ten cuidado de no sobrecalentar el iOpener durante la reparación. El sobrecalentamiento puede provocar que el iOpener se rompa.

    • Nunca toques el iOpener si parece estar hinchado.

    • Si el iOpener esta todavía demasiado caliente al tacto, sigue utilizándolo mientras esperas a que se enfríe un poco más antes de recalentar. Un iOpener adecuadamente climatizado debe mantenerse caliente durante un máximo de 10 minutos.

    May I know the temperate limit about heating iOpener? (maximum 150 degrees Celsius?) thx so much.

    yamayhuang - Contestar

    I had to heat mine up for more than 30 seconds. After 30 seconds on high it was only warm. It had to keep trying different times and checking it until it got hot. I think the initial time that I put it in for was over a minute.

    whale13 - Contestar

    DO NOT USE IN NON ROTATING MICROWAVE! It will pop a hole. I had it in for 45 seconds the first time. It wasn't very hot inside and I saw it started to leak on the paper towel I put under it. Just a fair bit of advice. I think I will just stick with the heat gun. Loud but useful.

    Alex Jackson - Contestar

    I don't own a microwave.

    mdanihy - Contestar

    Its again waterproof when you change iphone 7 battery?

    Jon - Contestar

    I don't have a microwave???

    Joe Blow - Contestar

    30 sec at which equivalent watts setting and what temperature does iOpener heats up to for 30 secs. Only just bought it so needs info before using it. Thanks

    Sam Stieg - Contestar

    can i use just ordinary microwave???

    juneseok kwon - Contestar

    If I don't have a microwave then I try to use hot air gun so how many munuts i want to heat ?

    Mohideen Rifay - Contestar

    I heated mine up for 30 seconds, tested, then again for 30 seconds. It felt adequately hot. Leaving it on the left side, per the instruction, for a minute did not loosen the adhesive. I ended up pulling the suction cup hard enough to shadder the old screen. Moral of the story, I don't think it gets hot enough safely to have an affect.

    Travis Dixon - Contestar

    There is a clear problem here with the heating part using the iopener things....no details are given. Whoever is testing them needs to make it clear - What temperature does it need to be? And for which phone models, because they differ in what's needed. It's only £10-15 for a laser guided temp sensor unit, and the designers/repairers should have one of those already for doing these kinds of repairs. Explaining half a repair, is worse than not explaining at all :-(

    assortedrubbish - Contestar

    All phones/devices differ it’s unrealistic and unsafe to put a exact time/temperature needed to soften the adhesive. It’s really quite simple you warm the device evenly and in a controlled manner just enough to enable pry tools and picks to begin separating. Best tool in my opinion but again this is because I have experience is a hot plate and heat gun both of which are used at nearly the lowest settings and I can handle flat palming the plate for almost 10 seconds I leave the device to conduct heat until approx it’s about 110 at most 120 ish this will be plenty to soften all the adhesive if any problem areas I use heat gun while prying. Again you need go slowly and learn with a throw away phone

    Greg Latta -

    I used a hot water bottle, works well as it covers the whole screen and stays hot for longer.

    dave - Contestar

    If I may suggest include your microwave wattage so people can get an idea on time for there own

    Patrick Storey - Contestar

    I ended up using a hair dryer. That iOpener thing took forever.

    mark fitzgerald - Contestar

    30 seconds sure isn’t cutting it… 45 didn’t get the screen of my iPad air 2 to budge either… even after resting on the ipad for 4 minutes.

    60 seconds in the microwave, the iOpener burst.

    I’ll get a new one and try once more with heating it 45 seconds and repeat that for 30 minutes like others have said here. If that doesn’t work it’ll have to be the heat gun.

    K

    Karl Marble - Contestar

    I can’t recommend the microwave. If the the iOpener becomes too hot, it bursts. Better put the opener in cooking water. Dry it and use it. Instead of an iOpener you can use hot/cool packs as well.

    Bernhard Keim - Contestar

    Trust the directions! I forgot and left it in the Microwave too long and after 1 minute I had Mt Vesuvius - the iOpener burst and spewed the goodies out. The problem is, the Digitizer can be damaged by a hot air gun, so I had to tough out and remove the glue the hard way. I made it … with lots of patience! Tough lesson.

    Larry Bennett - Contestar

    I also used a hairdryer. I used it on the low setting and I cut a piece of carboard to protect the rest of the screen. The iFixit tool and method is vert tedious and very time consuming in comparison. With the hairdryer method you can literally have the display apart in a few minutes. Using your other hand nearby the area you are heating it should be very hot but not enough to burn your hand. You only have to heat metal part of case near glass edge. If you have a cellular model then you need to be very careful because the black antenna area is plastic. So less heat and work your way up in adding heat just enough to separate around the area but not so much you melt the plastic!

    Fixrights - Contestar

    iOpener was the worst part of the kit. Followed directions for :30 in microwave and took 4 trips to the microwave to loosen adhesive on left side of home button. I thought I was figuring it out and it was working well… even set a timer to wait 10 minutes between heating it up. Was on the right side and was on my 12th heat up when it exploded in the microwave. My only tip is that if you set it clear side up, as soon as you see any bubbles or boiling in the liquid, STOP! If you put a pot holder over the iOpener and press slightly to make good surface contact, that seemed to help. I finished heating with a “Corn Sack” that held heat better than the provided iOpener.

    digital_only - Contestar

    Mon iopener n'a pas tenu une réparation. Je ne vous conseille pas ce produit

    Berard Romain - Contestar

    Bonjour,

    Nous sommes désolés que votre réparation ne se soit pas déroulée comme prévu. Il se peut que le produit était défectueux. Veuillez contacter notre service client support@ifixit.com (boutique américaine) ou eustore@ifixit.com (boutique européenne) en décrivant ce qui s’est passé.

    Claire Rapp -

    Readers looking for temperature advice might check the comments of the previous instruction, as there are more there. I used an immersion bath to heat this to 180F and applied it to the device until the outside temperature of the opener read 150F with an IR thermometer. Removing the screen took very little force with this method.

    breadandbits - Contestar

  4. Saca el iOpener del microondas, cogiéndolo por una de las esquinas planas para evitar el centro caliente.
    • Saca el iOpener del microondas, cogiéndolo por una de las esquinas planas para evitar el centro caliente.

    • El iOpener estará muy caliente, ten cuidado cuando lo manipules. Utiliza guantes de horno si es necesario.

    Will a hair dryer work for heating the glass?

    Me berg - Contestar

    Can you use an oven instead?

    Rafael -

    Yes, as does a heat gun.

    anonymous 4602 - Contestar

    I did this repair. I used a hair dryer, I think it works better: gets very hot fast.

    Cobus de Beer - Contestar

    microwave on WHAT WATTAGE ??? 100 W OR 1600 W ??? NOT THE SAME

    Ivor Pocrnja - Contestar

    This was not easy. I finally got a pick under the glass of my moto x4 phone after placing my phone on my kitchen hot plate and letting the hot plate go up to about 160F—measuring with a candy thermometer. I was scared of it(either the phone or the iopener) getting too hot—I checked in with another online video and saw they used a 100C heat gun for 2 min on the left side: When I figured that was 212F I got braver with heating the phone.—My screen and display were already broken. I can’t say exactly how long the phone was on the hot plate at 150-160 because the hotplate annoyingly goes on and off not sustaining a stable temperatureprobably a few

    Nahariyah Mosenkis - Contestar

    Readers looking for temperature advice might check the comments of the previous instruction, as there are more there. I used an immersion bath to heat this to 180F and applied it to the device until the outside temperature of the opener read 150F with an IR thermometer. Removing the screen took very little force with this method. I don’t know how much microwaves vary in heating consistency with these pads, but knowing how inconsistent the temperature of a bowl of plain rice gets in my microwave, I wasn’t interested in even trying to use it for this.

    breadandbits - Contestar

  5. Abrir tu teléfono comprometerá los los sellos impermeables. Ten preparado adhesivo de reemplazo antes de proceder o ten cuidado para evitar exposición al líquido si vuelves a ensamblar tu teléfono sin reemplazar el adhesivo. Si tu vidrio está hecho pedazos, coloca cinta de embalaje sobre todo el panel para mantenerlo unido durante el proceso de eliminación.
    • Abrir tu teléfono comprometerá los los sellos impermeables. Ten preparado adhesivo de reemplazo antes de proceder o ten cuidado para evitar exposición al líquido si vuelves a ensamblar tu teléfono sin reemplazar el adhesivo.

    • Si tu vidrio está hecho pedazos, coloca cinta de embalaje sobre todo el panel para mantenerlo unido durante el proceso de eliminación.

    • Coloca el iOpener caliente sobre el panel trasero durante dos minutos para soltar el adhesivo alrededor del borde del cristal.

    • Necesitarás volver a calentar y aplicar el iOpener varias veces para alcanzar la temperatura suficiente. Consulta las instrucciones del iOpener para evitar sobrecalentamiento del dispositivo.

    • Mueve el iOpener para calentar la sección restante del panel durante dos minutos.

    • También se puede utilizar un secador de pelo, pistola de calor, o lámina caliente, pero ten cuidado de no sobre calentar el móvil -la pantalla OLED y la batería interna son susceptibles a daño por calor.

    are there any option out there that allows you to heat the adhesive outdoors without any power plug?

    Brotan Store - Contestar

    There's a star in the center of our solar system, you could try that.

    John Joiner -

    the way we do it at Get it fixed cellphone repair calgary is with a heat gun, wich is way easier than this, make sure to wear some gloves and dont worry to use to much heat as long as you point just to the back of the phone, (the back panel is thick enough to protect the logic board from over heat) instead of the usual blue plastic piece i sugest to use the thinnest metal razor knife and a business card so you can insert the business card and move it all around the frame, those blue plastic things are way too thick that will break the glass panel if you apply to much pressure

    get it fixed - Contestar

    After did that with my own heat pad, the white paint got ripped off but luckily glass back cover did not break. So I scratched all white part of the back cover and now its all transparent.

    Jae Chung - Contestar

    I used a purpose built heating device at 100 degree celsius. Lower temperatures didn't work.

    ken - Contestar

    I used a blow dryer, attached my multimeter heat sensor to the back to monitor the temperature. At 54 degrees Celsius I could separate the back with a suction cup from my phone without damaging the paint.

    LRD - Contestar

    I gave up on the hot bag after 4 heat and apply cycles. I was only getting the back up to 60c using an infrared thermometer. I switched to a harbor freight 1500w heat gun set to Low, moving constantly around the back, until the back read 95c. The back came off easily at that point.

    Nathan Wray - Contestar

    using a blowtorch on low heart for 3-5 seconds at close range also works

    Achi Namaratne - Contestar

    I found another site that said temps of 203F/95C were required to soften the glues. Once I started using those temps with my heat gun, as well as a tool I made by just cutting the flat front/back panel from a package of screws (any plastic package that has a flat panel will work) , I had the back off in no time. Had I continued to use the plastic pick shown in the instructions, I really doubt I would have gotten the back off since I couldn’t get enough force on the back from my suction cup. The thin package plastic acted almost like a knife as I moved it around the outside edge. WARNING: If you have to reheat the back, REMOVE THE PACKAGE PLASTIC!! It will start to melt from the heat of a heat gun. Good Luck!!

    morttormjch - Contestar

    I gave up after struggling 1 hour with an hairdryer, the glass was around 65°C and it doesn't wants to lift up at all, anybody got tips ?

    123321mario - Contestar

    What tools are you using Mario?

    vazersecurity -

    Iopener ist totaler Mist.

    Robert Palme - Contestar

    Wenn dann braucht man mehrere um das Panel gleichmäßig zu erhitzen

    Robert Palme - Contestar

    I had a pristine s6 edge I’m replacing the battery in. I can agree with many others about the amount of heart needed and need to where gloves. I had to heat several times using a heat gun. After several attempts phone broke free from suction cup went flying and now I have a phone with broken screen. Oh well, glad it’s not my primary phone. After getting it above 100c, the back glass finally started to separate. You need another person to be ready with a pick. Once you get one pick in, the rest is .

    Brian Gillan - Contestar

  6. Una vez que el panel esté lo suficientemente caliente al tacto, coloca una ventosa lo más cerca posible del borde calentado, evitando la parte curvada. Levanta de la ventosa para crear un pequeño espacio por debajo del cristal trasero e inserta una púa de apertura en el espacio. Como opción, una vez que la púa esté introducida, puedes agregar unas pocas gotas de alcohol isopropílico dentro del espacio para ayudar a debilitar el adhesivo en los pasos siguientes.
    • Una vez que el panel esté lo suficientemente caliente al tacto, coloca una ventosa lo más cerca posible del borde calentado, evitando la parte curvada.

    • Levanta de la ventosa para crear un pequeño espacio por debajo del cristal trasero e inserta una púa de apertura en el espacio.

    • Como opción, una vez que la púa esté introducida, puedes agregar unas pocas gotas de alcohol isopropílico dentro del espacio para ayudar a debilitar el adhesivo en los pasos siguientes.

    If the rear screen is cracked/smashed, you will not be able to use a suction cup to remove it. The suction could would not seal because of the cracks. I tried masking tape, 3M shiny HVAC tape, and others, and the suction could would not seal to those surfaces either.

    I ended up using the sharp point of the smudger to remove some shards of glass to get underneath the cover to leverage it up and out. Definitely use gloves and safety glasses if you have to do this.

    dougpender - Contestar

    Thank you for your comment. I needed to see this particular instance of what to do when the back cover was cracked. I was going to try to suction it with tape covering it. This saved me some heartache. You're an angel!!

    Jessie Brooks -

    Be careful during this step- reapply heat before attempting this one (battery issues tend to melt internal “areas” ) and this area is most prone to crack during the lifting of the back plate.

    Briannah - Contestar

    J’ai utilisé la même ventouse.

    En soulevant la poignée rabattable, la simple succion a aspiré un disque de verre ! J’ai brisé la vitre sans même tirer…

    pierre brunet - Contestar

    I think it is just about impossible to do this without at least removing some paint on the edges. Order a new back before you attempt this. It has the adhesive already on it and costs less than $10 on eBay.

    Thomas Hayes - Contestar

    In order to get in more easily, I normally use the iFlex (the metal one) which is thin enough to create a little space, and then i insert a thinner plastic sheet, just like the default screen protector you might find on some huawei or xiaomi phones. That plus half a drop of alcohol should do the trick. Use caution and be very patient.

    Stefano Restuccia - Contestar

  7. Desliza la púa de apertura a lo largo del borde del teléfono separando el adhesivo que sujeta el cristal trasero. Luego, podría ayudar dejar la púa en su lugar y toma una segunda púa mientras procedes con el paso siguiente. Al dejar la púa insertada podría ayudar a prevenir que el pegamento que separes se vuelva a adherir.
    • Desliza la púa de apertura a lo largo del borde del teléfono separando el adhesivo que sujeta el cristal trasero.

    • Luego, podría ayudar dejar la púa en su lugar y toma una segunda púa mientras procedes con el paso siguiente. Al dejar la púa insertada podría ayudar a prevenir que el pegamento que separes se vuelva a adherir.

    • Vuelve a calentar el cristal trasero cuando sea necesario para prevenir que el pegamento se enfría y endurezca.

    Be careful that the bottom of the phone is well heated, and add a drop or so of isopropyl alcohol. When I removed the back glass of my S6, some of the black coating on the glass stayed stuck to the adhesive, so to return my phone to its original appearance, I’ll have to get a new back glass.

    Gary F - Contestar

  8. Repite el paso previo de calentado y corte del adhesivo en los tres bordes restantes. Deja una púa de apertura en cada borde del dispositivo mientras continúas para evitar que se vuelva a unir con el adhesivo. Deja una púa de apertura en cada borde del dispositivo mientras continúas para evitar que se vuelva a unir con el adhesivo.
    • Repite el paso previo de calentado y corte del adhesivo en los tres bordes restantes.

    • Deja una púa de apertura en cada borde del dispositivo mientras continúas para evitar que se vuelva a unir con el adhesivo.

    At this stage I didn’t use a plastic pick as I think they are too thick and will crack a screen that’s not already cracked. I used a stainless steel

    I sesame blade which does a much better job of cutting through the adhesive. Just be careful not to insert it in too far. I sometimes put a mark on my blade to ensure it doesn’t go in too far.

    Wayne Lyell - Contestar

    I used a card like the ones people use to play poker or any card game with. Only one was needed to separate the back without any damage to the paint.

    LRD - Contestar

    Be sure to apply a decent amount of heat when removing the last bit of the rear glass, cracked the rear of my screen (only a small amount mind) trying too use too much force not enough heat for the last spot.

    spank2103 - Contestar

  9. Kits para Nintendo Switch

    Una solución rápida para volver al juego

    Comprar kits de Switch

    Kits para Nintendo Switch

    Una solución rápida para volver al juego

    Comprar kits de Switch
  10. Usa una púa de apertura para cortar cualquier adhesivo restante. Remueve el cristal trasero.
    • Usa una púa de apertura para cortar cualquier adhesivo restante.

    • Remueve el cristal trasero.

    The rear glass is very fragile. I cracked mine across the camera opening while cleaning off the old sealant. Next time ( I will have to order one and do it again…doh) I’ll place it on a flat surface while cleaning it.

    Greg Scott - Contestar

    This is also a really good time to remove the SIM tray

    John Murphy - Contestar

  11. Para instalar un cristal trasero nuevo: Usa pinzas para despegar cualquier adhesivo restante de cristal trasero y el chasis del teléfono.
    • Para instalar un cristal trasero nuevo:

    • Usa pinzas para despegar cualquier adhesivo restante de cristal trasero y el chasis del teléfono.

    • Luego, limpia las áreas de adhesión con alcohol isopropólico de concentración alta ( al menos 90%) y un paño anti-pelusa. Desliza en una dirección solamente, no desde atrás hacia adelante. Esto ayudará a preparar la superficie para un adhesivo nuevo.

    • Despega el adhesivo del nuevo cristal trasero, alinea cuidadosamente un borde del cristal contra el chasis del teléfono y presiona firmemente el cristal contra el teléfono.

    • Si estás reinstalando el viejo cristal trasero, o usando el cristal trasero sin el adhesivo preinstalado, sigue esta guía.

    You should note that the adhesive strip may need to be fully removed from the frame in order to proceed with repairs. The adhesive on my phone covered all of the screws exposed in the next step.

    Sean Cruz - Contestar

    When I did my battery, the adhesive stayed almost 100% on the back glass and was still in good shape. What didn’t remain attached only lifted slightly and I was able to coax it back to its original location with tweezers. I didn’t bother to remove and replace the adhesive layer because mine was still good. I set the glass out of the way where it wouldn’t get dirt on the adhesive while I finished the battery swap. I added some additional heat (hair dryer) after reattaching the glass to make sure the adhesive made the best seal.

    Wayne Thomason - Contestar

  12. Remueve los trece tornillos de 3.3 mm Phillips #00 del marco medio.
    • Remueve los trece tornillos de 3.3 mm Phillips #00 del marco medio.

    Do yall sell the screws and the screw organization mat

    The lit asf Channel - Contestar

  13. Presiona la parte trasera de la batería y levanta los bordes del marco medio para separarlo del resto del teléfono. Presiona la parte trasera de la batería y levanta los bordes del marco medio para separarlo del resto del teléfono. Presiona la parte trasera de la batería y levanta los bordes del marco medio para separarlo del resto del teléfono.
    • Presiona la parte trasera de la batería y levanta los bordes del marco medio para separarlo del resto del teléfono.

  14. Usa el extremo plano de un spudger, desconecta el cable plano de batería de la placa madre. Usa el extremo plano de un spudger, desconecta el cable plano de batería de la placa madre.
    • Usa el extremo plano de un spudger, desconecta el cable plano de batería de la placa madre.

    Hello ! Is there a way i can buy only this flex cord that you are showing . A GSM service broke it and wont fix my phone

    Lica Mihai-Alexandru - Contestar

  15. Desconecta el cable cinta del botón de inicio de la placa madre. Desconecta el cable cinta del botón de inicio de la placa madre.
    • Desconecta el cable cinta del botón de inicio de la placa madre.

  16. Usa el extremo puntiagudo de un spudger para desconectar los dos cables de interconexión de antena de la placa madre. Usa el extremo puntiagudo de un spudger para desconectar los dos cables de interconexión de antena de la placa madre. Usa el extremo puntiagudo de un spudger para desconectar los dos cables de interconexión de antena de la placa madre.
    • Usa el extremo puntiagudo de un spudger para desconectar los dos cables de interconexión de antena de la placa madre.

  17. Desconecta el cable de cinta de pantalla de la placa madre utilizando el extremo plano del spudger. Desconecta el cable de cinta de pantalla de la placa madre utilizando el extremo plano del spudger.
    • Desconecta el cable de cinta de pantalla de la placa madre utilizando el extremo plano del spudger.

  18. Desconecta el cable de cinta de auricular de la placa madre. Desconecta el cable de cinta de auricular de la placa madre.
    • Desconecta el cable de cinta de auricular de la placa madre.

  19. La placa madre es un componente sensible a descargas eléctricas y debe ser tratada con cuidado. iFixit recomienda usar un brazalete antiestático cada vez que tratas componentes de esta naturaleza para evitar daños. Toma la placa madre de ambos bordes hacia la parte superior del dispositivo.
    • La placa madre es un componente sensible a descargas eléctricas y debe ser tratada con cuidado. iFixit recomienda usar un brazalete antiestático cada vez que tratas componentes de esta naturaleza para evitar daños.

    • Toma la placa madre de ambos bordes hacia la parte superior del dispositivo.

    • No levantes la placa madre totalmente en este paso; el cable plano en la parte inferior debe ser desconectado primero.

    • Levanta la placa madre de la pantalla, teniendo cuidado de no ejercer demasiado estrés en el cable plano de la placa hija.

    Better to remove the antenna connector from daughter board and keep the connector on main board, as You will planning to remove it you will need to take from it anyway.

    Gabriel Pinho - Contestar

  20. Desconecta el cable plano de la placa hija de la parte inferior de la placa madre. Desconecta el cable plano de la placa hija de la parte inferior de la placa madre.
    • Desconecta el cable plano de la placa hija de la parte inferior de la placa madre.

    I had trouble removing the daughter board connector so I gently folded the main board back and was able to remove the battery.

    Eric Bornstein - Contestar

  21. Remueve los dos tornillos Phillips #00 de 2.5 mm.
    • Remueve los dos tornillos Phillips #00 de 2.5 mm.

  22. Utilizando el extremo puntiagudo del spudger, levanta la pequeña sección de la placa hija sujetada con un adhesivo leve. Utilizando el extremo puntiagudo del spudger, levanta la pequeña sección de la placa hija sujetada con un adhesivo leve.
    • Utilizando el extremo puntiagudo del spudger, levanta la pequeña sección de la placa hija sujetada con un adhesivo leve.

    small section of daughterboard ribbon is broken is there any solution to fix it in this condition

    i am unable to find connections/ data sheet / diagram

    Zeeshan Jafri - Contestar

  23. Levanta la placa hija del cuerpo del teléfono para removerla. Levanta la placa hija del cuerpo del teléfono para removerla. Levanta la placa hija del cuerpo del teléfono para removerla.
    • Levanta la placa hija del cuerpo del teléfono para removerla.

    I think this step needs to add the need to carefully remove the soft key contacts? That’s where I’ve come unstuck :(

    Simone Casey - Contestar

Conclusión

Para volver a montar el dispositivo, sigue estas instrucciones en orden inverso. Cuando vuelvas a instalar el cristal trasero, consulta la guía para reemplazar el adhesivo de cristal trasero.

67 personas más completaron esta guía.

Un agradecimiento especial a estos traductores:

100%

¡ Mariana nos está ayudando a reparar el mundo! ¿Quieres contribuir?
Empezar a traducir ›

Sam Goldheart

Miembro Desde 18/10/12

413,997 Reputación

547 Guías creadas

Equipo

iFixit Miembro de iFixit

Community

125 Miembros

11,820 Guías creadas

quick question, s6 edge charging port G925i is it compatible with G925F.

George - Contestar

I was able to follow these directions to replace the daughter-board on my Galaxy s6. I have *NO* technical experience. The real difficulty was with the products from iFixit - the gel pad didn’t melt the adhesive (I used a heat gun instead), the “guitar pics” were too flimsy & the screwdriver was RIDICULOUSLY small…I bought a mini Craftsman set that made ALL the difference.

Jamie - Contestar

hey i need to get the version for Samsung s6 edge t mobile the whole charging system

the version G925i or G925F or which one and where can i ship it from?

jamal - Contestar

My Samsung charging cable was melted, and after this I could not charge phone using micro usb. I’ve replaced Charging Port Daughterboard, but after this there is no Fast Charge. This option turned On in setup, but phone charging +4h.

Charger replaced, usb cable with 5 pins.

Any issue?

Qba PL - Contestar

this for me was easy

RICHIE GEORGE GRAY - Contestar

I reqested a new daughterboard for Samsung galaxy s6 edge. I received a daughter board that does not match quite right. The original has a SM -0925v sub USB. The daughterboard I received has a SM- 0928V SUB USB. it does not fit.

Kathy Carkhuff - Contestar

Hi.

Can we use g925f model charging board in g925i ?

sidhaan9 - Contestar

On reassembly don't forget to move the Bluetooth and sell antenna over to the new daughter board

Steven Williams - Contestar

small section of daughterboard ribbon is broken is there any solution to fix it in this condition

i am unable to find connections/ data sheet / diagram

Zeeshan Jafri - Contestar

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 9

Ultimos 7 días: 139

Ultimos 30 días: 632

Todo El Tiempo: 60,152