Saltar al contenido principal

Reemplazo de pantalla con marco del Huawei P9 Lite

Qué necesitas

  1. Reemplazo de pantalla con marco del Huawei P9 Lite, Tapa trasera: paso 1, imagen 1 de 2 Reemplazo de pantalla con marco del Huawei P9 Lite, Tapa trasera: paso 1, imagen 2 de 2
    • Usa una púa de apertura para desenganchar la tapa trasera comenzando en la esquina inferior.

    • Sigue pasando la púa en dirección contraria a la agujas del reloj y con cuidado haz palanca en las lengüetas plásticas para abrirlas una a la vez.

    What could you use instead of an opening pick??

    Alfredo - Contestar

    Like, could a guitar pick wor? Or anything else?

    Alfredo - Contestar

    A guitar pick will also do.

    Tobias Isakeit -

    what can still be used besides guitar pick

    Tarshia Thompson - Contestar

    I had a hard time to open the back cover by opening pick. Then I used little, really little knife at first, and I continue to opening back cover using opening pick.

    Andy B - Contestar

    Heating up aroud the finger sensor to loosen the square adhesive tape ..

    Hishamchohan - Contestar

    If you do not have any picks, You can also adapt an old credit or utility card by cutting it in to thirds. Then with some fine emery or sand paper, rub a sharp point on the one edge of the card. This will help you get access to the clips that hold the rear cover on. The one i did yesterday had quite a lot of adhesive around the edge & around the finger print sensor. Another tip with an old credit card is to cut it in to narrow strips to insert in to where you have separated the cover from the frame to stop it getting stuck to the adhesive again.

    gazza667 - Contestar

  2. Reemplazo de pantalla con marco del Huawei P9 Lite: paso 2, imagen 1 de 1
    • Hay un adhesivo por debajo de la tapa trasera que sujeta la batería y la placa de metal en la parte superior.

    • Ten cuidado con el cable flex del lado derecho.

    • Tuerce la púa de apertura para hacer palanca en la tapa trasera y soltarla del adhesivo.

    Most of the adhesive is around the fingerprint cell and on the battery itself. You can slowly pull the back cover from its side but make sure not to break it. Push the mediator or a longer piece of plastic under the back cover to slowly destroy the adhesive.

    Nicolas Combaret - Contestar

    Slowly, slowly wins the day. Nicolas is right and comes off a charm. The most nerve wracking part of this longish repair.

    John Nordstrom - Contestar

  3. Reemplazo de pantalla con marco del Huawei P9 Lite: paso 3, imagen 1 de 1
    • Cuando la tapa trasera se libera del adhesivo puedas sacar con la mano completamente.

    Hi! Im so sad! At the begginig of the operation i ve broken the white seal/connector that in one side is connected to the board and the other side is "glued" to the battery. Can someone help me? how can i solve this?? There is no image displayed on the screen. but there is vibration, sound, notifications... can someone help me please???

    Diogo - Contestar

    What you broke is handling the NFC, and doesn’t have anything to do with the display. You probably damaged the ribbon right below the battery, since that’s what links the display to the motherboard.

    Polaris -

    Oups ! L’antenne NFC était solidement collée à l’intérieur de la coque et j’ai donc déchiré sa nappe en ouvrant la coque. Heureusement, je n’utilise pas les fonctions NFC et, à part cela, tout a l’air de fonctionner normalement.

    Michel Orban - Contestar

  4. Reemplazo de pantalla con marco del Huawei P9 Lite, Escudo de la placa madre: paso 4, imagen 1 de 1
    • Remueve los nueve tornillos Phillips #00 que sujetan la placa de escudo de metal.

    • Algunos tornillos podrían estar cubiertos con pegatinas a prueba de manipulaciones. Remuévelas para asegurarte de que tu controlador encaje bien.

    Qu’est ce qu’un “indicateur d’eau”?

    chevaliernoir - Contestar

    Une petite pastille qui change de couleur au contact de l’eau. Les fabricants s’en servent pour nullifier la garantie : si ta pastille indique que de l’eau s’est infiltré, tu devra payer ta réparation.

    Polaris -

    Are all the screws the same size ?

    Hishamchohan - Contestar

    yes they are

    Adam M -

  5. Reemplazo de pantalla con marco del Huawei P9 Lite: paso 5, imagen 1 de 2 Reemplazo de pantalla con marco del Huawei P9 Lite: paso 5, imagen 2 de 2
    • No remuevas la placa de escudo aun ya que está sujeta por un conector y un cable adherido.

    • Usa un spudger para desconectar el sensor de huella digital de su placa madre.

    • Despega el cable de antena NFC de la placa de metal.

    can we just remove NFC antenna and dont want to install int back?

    Mohd Danial Bin Harun - Contestar

    Note there are two plastic tabs at the top of the shield plate. Unlock them with a mediator, the plate will come easily after that.

    Nicolas Combaret - Contestar

    Buongiorno,

    va sostituita l'intera piastra metallica contenente il sensore impronte e la fotocamera, oppure il sensore é estraibile dalla piastra?

    Grazie

    LUIGI

    GI GI - Contestar

    Yes, it is possible to remove just the fingerprint sensor from the motherboard shield. Remove the small metal plate on the inside of the shield covering the sensor and push the fingerprint sensor through from the other side.

    Tobias Isakeit -

  6. Reemplazo de pantalla con marco del Huawei P9 Lite, Placa madre: paso 6, imagen 1 de 2 Reemplazo de pantalla con marco del Huawei P9 Lite, Placa madre: paso 6, imagen 2 de 2
    • Remueve la bandeja de la tarjeta SIM.

  7. Reemplazo de pantalla con marco del Huawei P9 Lite: paso 7, imagen 1 de 3 Reemplazo de pantalla con marco del Huawei P9 Lite: paso 7, imagen 2 de 3 Reemplazo de pantalla con marco del Huawei P9 Lite: paso 7, imagen 3 de 3
    • Desconecta el cable flex de placa madre, el cable flex de la batería y el cable de antena.

  8. Reemplazo de pantalla con marco del Huawei P9 Lite: paso 8, imagen 1 de 2 Reemplazo de pantalla con marco del Huawei P9 Lite: paso 8, imagen 2 de 2
    • Desconecta el cable flex de pantalla y el cable de botón de encendido y botón de volumen.

  9. Reemplazo de pantalla con marco del Huawei P9 Lite: paso 9, imagen 1 de 2 Reemplazo de pantalla con marco del Huawei P9 Lite: paso 9, imagen 2 de 2
    • Desenchufa la cámara trasera y la toma de auriculares.

  10. Reemplazo de pantalla con marco del Huawei P9 Lite: paso 10, imagen 1 de 2 Reemplazo de pantalla con marco del Huawei P9 Lite: paso 10, imagen 2 de 2
    • Saca la cámara y la toma de auriculares de sus zócalos.

  11. Reemplazo de pantalla con marco del Huawei P9 Lite: paso 11, imagen 1 de 3 Reemplazo de pantalla con marco del Huawei P9 Lite: paso 11, imagen 2 de 3 Reemplazo de pantalla con marco del Huawei P9 Lite: paso 11, imagen 3 de 3
    • Usa un spudger para levantar la placa madre con cuidado.

    • Remueve el ensamblaje de placa madre.

    • En la parte posterior de la placa madre hay una almohadilla térmica (gota tipo goma color rosa) para disipar el calor. Si estás a punto de reemplazar el ensamblaje de la pantalla, y la almohadilla térmica se rompió o está demasiado seca, es posible que desees reemplazarlo por una nueva.

  12. Reemplazo de pantalla con marco del Huawei P9 Lite, Pantalla con marco: paso 12, imagen 1 de 2 Reemplazo de pantalla con marco del Huawei P9 Lite, Pantalla con marco: paso 12, imagen 2 de 2
    • Remueve la tapa de goma del micrófono y el altavoz auricular.

  13. Reemplazo de pantalla con marco del Huawei P9 Lite: paso 13, imagen 1 de 1
    • Remueve los siete tornillos del altavoz:

    • Tres tornillos plateados de 2.9 mm Phillips #00

    • Cuatro tornillos negros de 3.8 mm Phillips #00

  14. Reemplazo de pantalla con marco del Huawei P9 Lite: paso 14, imagen 1 de 1
    • Remueve el altavoz.

  15. Reemplazo de pantalla con marco del Huawei P9 Lite: paso 15, imagen 1 de 2 Reemplazo de pantalla con marco del Huawei P9 Lite: paso 15, imagen 2 de 2
    • Desenchufa el cable flexible de la placa madre y desconecta el cable de antena.

    • Aparta ambos cables a un lado.

  16. Reemplazo de pantalla con marco del Huawei P9 Lite: paso 16, imagen 1 de 3 Reemplazo de pantalla con marco del Huawei P9 Lite: paso 16, imagen 2 de 3 Reemplazo de pantalla con marco del Huawei P9 Lite: paso 16, imagen 3 de 3
    • Ahora remueve la placa hija.

    • Con cuidado despega el contacto del motor de vibración y sácalo.

    • También remueve el armazón del micrófono inferior.

    Be extra careful when removing the vibrator motor ( I ripped the flex ). The flex is easy to detach but the motor is glued a bit deeper in the frame, and it’s tricky to extract. I naively thought if I applied a lever from the top side, where the flex reaches (following the ungluing of the flex cable) I could get it out, but I ripped the flex in doing so. you have to come and lift it up from the right side preferably. On the other hand if you ripped the flex, it’s no biggy. Just save the part and don’t put it back in the new frame, your phone will work but not vibrate. I always hated that thing anyway ! Otherwise you can buy a new part (non OEM) for a few euros on Amazon.

    Georgeses - Contestar

  17. Reemplazo de pantalla con marco del Huawei P9 Lite: paso 17, imagen 1 de 3 Reemplazo de pantalla con marco del Huawei P9 Lite: paso 17, imagen 2 de 3 Reemplazo de pantalla con marco del Huawei P9 Lite: paso 17, imagen 3 de 3
    • Solo haz palanca a lo largo del borde de la bandeja SIM de la batería para proteger el cable flexible de pantalla que va por debajo del centro de la batería.

    • Inserta un spudger o una herramienta fina de palanqueo en un ángulo bajo para evitar doblar la batería y levantarla de su adhesivo.

    • Compara la parte nueva con la vieja para verificar si hay pequeños componentes que necesitan ser transferidos como botones o juntas.

    • Nunca vuelvas a instalar una batería que ha sido doblada o dañada al ser removida.

    Good guide, repaired without problems

    Enrico - Contestar

    Really good guide - mine seemed to have a lot more glue holding things down but eventually got it all apart, One additional thing - if you need to transplant the power and volume buttons from the old frame, they just sit in an opening on the side, but be aware that they may be glued into place.

    Rich Jeffery - Contestar

    I agree with the comment above. I removed the on/off and volume buttons with an old style razor blade to cut through the glue between the body and the back of the buttons. Also I would recommend buying a new battery as I totally ruined mine trying to un-stick it from the old frame.

    Tim Henry - Contestar

    Same from me: everything in instruction very accurate described except power/volume buttons replacement. Most of frames comming from Chine are without these buttons and transfer from old one is required ;)

    Rimantas Grigaliunas - Contestar

    Yup, a lot of glue as well and I had to bend my battery slightly. I didn’t pierce or rip it though, so I risked putting in back with the new piece. It works, but battery performance is affected. I would recommend buying a new battery and changing it at the same time. The adhesive is already in place on the new frame, so no need for double sided tape.

    Georgeses - Contestar

    Also volume up down and power buttons were not on the new frame. I had to get them from the new frame and they were glued were strongly.

    Before you consider taking them out, make sure to remember how the little gray plastic cover on top was put (that bit was not glued by the way, it’s the actual button underneath which is), since you may have a headache putting it back in place on the new frame. You will know you got it right when all three buttons “click” when all is done.

    As for the ungluing, the only way I could get them out was by first ungluing the screen with iopener/suction handle/picks (although my screen was way too broken for that too work, in the end I had to push through the broken screen by a small hole in the old frame, where the battery was before).

    Georgeses - Contestar

    Once you get the screen off the old frame, there’s a small black tape where the buttons are on the other side. Remove it first, and from there you can see the buttons and push them out. You have to cut out the glue first though. I used one tip of the tweezers since they were thinner and stronger than the plastic spudge and “sawed” between the buttons and the frame, that’s where the glue is. Be careful to saw between the button and the frame and not between the circuits and the buttons (orange layer and metal piece), or you will wreck it. Also be careful when you reach the middle between the two volume buttons (I think, just check from the inside) since that is where the circuits merge into the flex that connects to the motherboard.

    Georgeses - Contestar

Conclusión

Para volver a ensamblar tu dispositivo, sigue estas instrucciones en orden inverso.

39 personas más completaron esta guía.

Un agradecimiento especial a estos traductores:

en es

100%

¡ Mariana Roca nos está ayudando a reparar el mundo! ¿Quieres contribuir?
Empezar a traducir ›

Tobias Isakeit

Miembro Desde 03/31/14

117,293 Reputación

188 Guías creadas

Equipo

Master Techs Miembro de Master Techs

Community

322 Miembros

2,521 Guías creadas

7 comentarios

I finished to replace the display yesterday and everything is perfect , thanks ifixit

husam faraj - Contestar

i replaced the display but the touchscreen doesn’t work

Michele Rappazzo - Contestar

You can try to reopen the phone and check if the flex cable is plugged in correctly or if any cable is ripped. If you can’t find any damage and all cables are plugged in correctly it’s possibly an issue with the replacement part.

Dominik Schnabelrauch -

Hi, could you show how to replace the power button flex cable for a P9 Lite 2017? I would be greatful.

szaszisti - Contestar

my powerbutton connection is also missing…

lorenz_untersulzner -

Ho riparato il cellulare e realmente la guida è fatta molto bene, Grazie!

Ermanno Marota - Contestar

Great guide ! I added a few comments under the relevant steps for the following issues (they were my doing though, the guide is great) :

STEP 16 Be extra careful when removing the vibrator motor as it is rather easy to rip the flex.

STEP 17 I had to get the volume up/down and power buttons from the old frame and that proved tricky (see my comments under step 17). Mind you that is not the outer plastic button but the inner metal button and circuits. You will know it’s not there by pressing the buttons to see if they “click”.

*I STRONGLY RECOMMEND BUYING A NEW BATTERY TOGETHER WITH THE SCREEN* I was able to remove my battery without wrecking it but the slight deformation still affected battery performance in the end (a lot). I highly doubt it is possible to do this repair without harming the battery.

Georgeses - Contestar

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 0

Ultimos 7 días: 10

Ultimos 30 días: 27

Todo El Tiempo: 25,125