Introducción
Usa esta guía para reemplazar el marco medio de tu Samsung Galaxy S4.
Qué necesitas
-
-
Haz palanca con una herramienta de apertura de plástico o tu uña en la ranura a la izquierda de la cámara trasera cerca del botón del encendido.
-
-
-
Levanta la caja trasera por la esquina más cerca de la ranura y remuévelo del teléfono.
I purchased a blue plastic opening tool(AKA: Spudge) like the one used in the above Step 1 rear cover pic and found the divot and was able to take off the rear cover as per the “Step 2 “ instructions.
-
-
-
Usa el extremo plano de un spudger, o tu uña para presionar la tarjeta microSD un poco más en su ranura hasta que escuches un clic.
-
Luego del clic, libera la tarjeta y saldrá de su ranura.
-
Remueve la tarjeta microSD.
I was able to remove the MicroSD Card as per the Step 3 MicroSD instructions with no problems.
-
-
-
Inserta una herramienta de apertura de plástico o un dedo en la muesca del compartimiento de la batería y levanta la batería.
-
Remueve la batería de tu teléfono.
-
-
-
-
Usa esta herramienta de apertura de plástico o tu uña para presionar la tarjeta SIM en su ranura hasta que escuches un clic.
-
Luego del clic, libera la tarjeta y saldrá de su ranura.
-
Remueve la tarjeta SIM.
Looks easy but doesn't work. No one has a plastic opening tool. Using fingernail, you can press SIM card into slot but it does not pop out so you can remove it.
I agree with the comment above
I also don't have a plastic tool and my finger nail won't pop the card out.
Grethe Montano. September 22
-
-
-
Remueve los nueve tornillos Phillips #00 de 4.00 mm que sujetan el marco medio al ensamblaje de pantalla.
How much cost will be on replace a midframe
I purchased a 1.5x40mm Phillips screw driver and was able to remove all 9 40mm screws from the midframe as per the Step 6 Midframe instructions.
-
-
-
Comenzando en el botón de volumen del teléfono, inserta la herramienta de apertura de plástico entre el bisel cromado alrededor del cristal de la pantalla y la pieza de borde cromada más grande. Busca la unión entre los dos.
-
Desliza la herramienta de apertura a lo largo de la unión separando los clips de plástico a medida que avanza.
I used same tool as in the photo and i broke the display. I think you should use a very thin plastic tool, such as a credit card but even more thin and flexible.
I purchased a blue plastic opening tool(AKA: Spudger) and was able to remove the midframe from the display assembly as per the Step 7. I had to hold the cell phone firmly in my left hand while I gently forced the spudger between the chrome bezel and the midframe with my right hand and heard plastics clips separate and saw the midframe start to separate from the display assembly. Don’t be afraid to get that spudger in and just gently go down the side of the phone and you will hear the plastics clips detach and the midframe to separate more and more until you are able to separate them 100%. I started at the volume button side of the phone in Step 7 and ended at the power button side in Step 9.
-
-
-
Continúa haciendo palanca alrededor de la esquina del teléfono.
-
Desliza la herramienta de apertura a lo largo de la línea entre el marco central y la pantalla a lo largo de la parte inferior del dispositivo, liberando más clips de plástico.
I purchased a blue plastic opening tool(AKA: Spudger) and was able to remove the midframe from the display assembly as per the Step 7. I had to hold the cell phone firmly in my left hand while I gently forced the spudger between the chrome bezel and the midframe with my right hand and heard plastics clips separate and saw the midframe start to separate from the display assembly. Don’t be afraid to get that spudger in and just gently go down the side of the phone and you will hear the plastics clips detach and the midframe to separate more and more until you are able to separate them 100%. I started at the volume button side of the phone in Step 7 and ended at the power button side in Step 9.
-
-
-
Continúa deslizando la herramienta de apertura alrededor de la parte superior del teléfono, liberando el último de los clips y liberando el medio marco del ensamblaje de la pantalla.
On my phone, there was another clip holding the white midframe to the battery compartment, in the middle of the top edge of the battery compartment, near the battery contacts. If you don't release that before removing the midframe, it is easy to break.
I purchased a blue plastic opening tool(AKA: Spudger) and was able to remove the midframe from the display assembly as per the Step 7. I had to hold the cell phone firmly in my left hand while I gently forced the spudger between the chrome bezel and the midframe with my right hand and heard plastics clips separate and saw the midframe start to separate from the display assembly. Don’t be afraid to get that spudger in and just gently go down the side of the phone and you will hear the plastics clips detach and the midframe to separate more and more until you are able to separate them 100%. I started at the volume button side of the phone in Step 7 and ended at the power button side in Step 9. In Step 10 just make sure all the plastic clips are separated from the midframe and the display assembly so you can pull them apart 100% without breaking them.
-
-
-
Remueve el marco medio del ensamblaje de pantalla.
My Sprint S4 was slightly different then the one pictured above but I just completed this repair in under 10 minutes.. It would have been slightly quicker but fooling around with those little screws can be irritating if you have big hands.
-
Para volver a ensamblar tu dispositivo, sigue estas instrucciones en orden inverso.
Para volver a ensamblar tu dispositivo, sigue estas instrucciones en orden inverso.
Cancelar: No complete esta guía.
93 personas más completaron esta guía.
Un agradecimiento especial a estos traductores:
100%
¡ Mariana Roca nos está ayudando a reparar el mundo! ¿Quieres contribuir?
Empezar a traducir ›
5 comentarios
I cracked the "front facing" bezel on my phone. I thought buying a new mid frame would replace it, but based on these pictures, it looks like it is attached to the the front glass. Is this correct? Is there any way to replace just that front facing bezel?
i was wondering the same thing. Can you guys please respond.
Yes, the bezel is attached to the front glass. Replacing the glass doesnt cost too much (under 15 eur here) but theres a high chance you will break the lcd digitizer in the process. It needs some skill.