Saltar al contenido principal

Reemplazo de las cámaras de cara posterior del iPhone X

Qué necesitas

  1. Reemplazo de las cámaras de cara posterior del iPhone X, Tornillos Pentalobe: paso 1, imagen 1 de 1
    • Antes de comenzar, descarga la bateria de tu iPhone por debajo de un 25%. Una bateria de litio cargada puede producir fuego o explotar si la pinchamos accidentalmente

    • Apaga tu dispositivo para comenzar a desarmarlo

    • Remueve los dos tornillos pentalobe de 6.9 mm de largo de la parte inferior del marco del iPhone

    • Si los tornillos están pelados o dañados, reemplace los tornillos.

    • Abrir la pantalla del dispositivo compromete los sellos a prueba de agua. Obtén algunos sellos de repuesto antes de proceder con el reemplazo, o ten cuidado de exponer tu teléfono a los líquidos si armas de nuevo el iPhone sin los sellos

    There are 6.81mm long screws!

    Daniel - Contestar

    One of the pentalobe screws is stripped :( - suggestions for how to get it out?

    cgtyoder - Contestar

    same situation here

    kaunomarcius - Contestar

    Same issue for me too, how do I get the stripped screw out?

    patronics - Contestar

    Update: I was able to get the “stripped” screw out using another Pentalobe-2 screwdriver bit from another company. It seems it wasn’t the screw, but the screw driver that was actually stripped. Hence why the other screwdriver kit I got came with 3 of this bit, I suppose.

    patronics - Contestar

    I ended up going to a jewelry store, and they drilled down into the screw, with of course an incredibly tiny bit. That allowed me to insert the P2 driver, and I was able to unscrew it at that point. Good luck!

    cgtyoder - Contestar

    Same issue with the stripping. The tip of the iFixit P2 head in my $70 kit just ground off on the first screw and that was that. Not much you can do.

    Kyle Harris - Contestar

    yes correct the same happened to me, the screws were perfect shaped never been open and as soon as i used the P2 it stripped the screws, seems like the P2 is slightly smaller but Dremel kit with a very small drill bits and precise knife tool is the way to go.

    Dulce Vidal - Contestar

    This step in automatically followed through, without any thought. Why remove these screws? Can anybody explain? The Screen is detachable all the same, with them well screwed in…

    Uri - Contestar

    These screws attach to a plate that’s part of the screen half of the phone. If you succeed in detaching the screen without removing those, it would seem reasonable that you will have damaged that plate or its ability to keep the two halves together.

    Dan Long -

    @Dan Long is right

    Uri -

    Clean out the pentalobe screw heads first so the tool goes all the way in. A small sewing needle works well to loosen any build up and then press some putty/chewing gum into the screw head and pull away quickly for a final clean out.

    William Olstad - Contestar

    The this kit should include screws because you’re going to strip them. Can’t even get past step one. Did anybody figure this out

    justin - Contestar

    Never opened my phone ever, when I went to look at the first step.. I noticed one of my screws was stripped. I thought it was impossible, but I removed the non stripped one, then once I got to the stripped one.. I learned my assumptions were correct. I bought this one straight from the apple site years ago ahaha Any tips to remove the stripped screw?

    Clarence Williams - Contestar

    William Olstad's tip about cleaning the screws with a needle and a bit of poster putty worked well for me. There was a lot of crud in there! The opening is shallow, so it's easy to see how the screwdriver wouldn't catch with even a bit of grit in the way, No problem getting the pentalobe screws out with the ifixit screwdriver.

    punkinann - Contestar

    If all else fails, very carefully cut a slot across the head of the screw with a Dremel tool using a diamond bit that dentist will gladly give you - I ask my dentist for used bits; and chuck them in a drill bit chuck designed for Dremel. The slot allows you to use a tiny, straight blade screwdriver. You can reuse the screw or replace it with a new pentalobe screw.

    Dan Smith - Contestar

  2. Reemplazo de las cámaras de cara posterior del iPhone X, Coloca cinta sobre cualquier grieta: paso 2, imagen 1 de 3 Reemplazo de las cámaras de cara posterior del iPhone X, Coloca cinta sobre cualquier grieta: paso 2, imagen 2 de 3 Reemplazo de las cámaras de cara posterior del iPhone X, Coloca cinta sobre cualquier grieta: paso 2, imagen 3 de 3
    • Si tu iPhone tiene una pantalla rota, mantén contenidas las roturas adicionales y evita daños corporales durante la reparación cubriendo el vidrio con cinta adhesiva.

    • Coloca tiras superpuestas de cinta de embalaje transparente sobre la pantalla del iPhone hasta cubrir toda la cara.

    • Usa anteojos de seguridad para proteger tus ojos de cualquier vidrio que se desprenda durante la reparación.

    • Si no puedes hacer que la ventosa se adhiera en los próximos pasos, dobla un trozo de cinta resistente (como cinta adhesiva) en un asa y levanta la pantalla con eso.

    • Si todo lo demás falla, puedes pegar la ventosa a la pantalla.

  3. Reemplazo de las cámaras de cara posterior del iPhone X, Instrucciones Anti-Clamp: paso 3, imagen 1 de 3 Reemplazo de las cámaras de cara posterior del iPhone X, Instrucciones Anti-Clamp: paso 3, imagen 2 de 3 Reemplazo de las cámaras de cara posterior del iPhone X, Instrucciones Anti-Clamp: paso 3, imagen 3 de 3
    • Los siguientes dos pasos muestran el Anti-Clamp, una herramienta que diseñamos para facilitar el procedimiento de apertura. Si no estás utilizando Anti-Clamp, salta tres pasos hacia abajo para obtener un método alternativo.

    • Para obtener instrucciones completas sobre cómo usar Anti-Clamp, consulta esta guía.

    • Tira de la manija azul hacia atrás para desbloquear los brazos del Anti-Clamp.

    • Desliza los brazos sobre el borde izquierdo o derecho de tu iPhone.

    • Coloca las ventosas cerca del borde inferior del iPhone, una en el frente y otra en la parte posterior.

    • Aprieta las copas para aplicar succión en el área deseada.

    • Si encuentras que la superficie de tu dispositivo es demasiado resbaladiza para que el Anti-Clamp la sujete, puedes usar cinta de embalaje para crear una superficie más adherente.

  4. Reemplazo de las cámaras de cara posterior del iPhone X: paso 4, imagen 1 de 3 Reemplazo de las cámaras de cara posterior del iPhone X: paso 4, imagen 2 de 3 Reemplazo de las cámaras de cara posterior del iPhone X: paso 4, imagen 3 de 3
    • Tira del mango azul hacia delante para bloquear los brazos.

    • Gira el mango en el sentido de las agujas del reloj 360 grados o hasta que las copas empiecen a estirarse.

    • Asegúrate de que las ventosas permanezcan alineadas entre sí. Si comienzan a salirse de la alineación, afloja ligeramente las ventosas y vuelve a alinear los brazos.

  5. Reemplazo de las cámaras de cara posterior del iPhone X: paso 5, imagen 1 de 3 Reemplazo de las cámaras de cara posterior del iPhone X: paso 5, imagen 2 de 3 Reemplazo de las cámaras de cara posterior del iPhone X: paso 5, imagen 3 de 3
    • Calienta un iOpener y pásalo por los brazos del Anti-Clamp.

    • También puedes utilizar un secador de pelo, una pistola de calor o una plancha caliente, pero el calor extremo puede dañar la pantalla y/o la batería interna, así que procede con cuidado.

    • Dobla el iOpener de forma que quede sobre el borde inferior del iPhone.

    • Espera un minuto para que el adhesivo se despegue y se abra el hueco.

    • Inserta una púa de apertura en el hueco que hay debajo de la pantalla y el bisel de plástico, no en la propia pantalla.

    • Si el Anti-Clamp no crea un espacio suficiente, aplica más calor al área y gira la manija en el sentido de las agujas del reloj media vuelta.

    • No dés más de media vuelta a la vez y espera un minuto entre vueltas. Deja que el Anti-Clamp y el tiempo hagan el trabajo por ti.

    • Omite los siguientes tres pasos.

    DO NOT separate the glass from the plastic bumper or rim around it. These instructions don't clarify that the pick has to be inserted between the plastic rim and the metal body. It is likely that the glass will lift slightly off the plastic surround before the plastic will lift out of the metal body. I had success sliding a card or pick back and forth along the bottom edge of the plastic rim while pulling on the suction cup. Eventually there was a space large enough for the pick to go under the plastic rim.

    Anessa - Contestar

    Thanks for pointing this out! I'll revise this step to clarify this point.

    Arthur Shi -

  6. Reemplazo de las cámaras de cara posterior del iPhone X: paso 6, imagen 1 de 1
    • Al calentar el borde inferior del iPhone se ablandará el adhesivo que sujeta la pantalla facilitando la apertura.

    • Usa un secador de pelo o una pistola de aire caliente o prepara un iOpener y aplícalo en el borde inferior del iPhone durante un minuto para ablandar el adhesivo que se encuentra debajo.

    General tip regarding heating necessary to remove adhesive:

    consider using a heated tip of a small screwdriver or metal spudger (not the one made of plastic, provided in kit), rather than to heat the device itself.

    Uri - Contestar

    You then need to be careful about the temp of the tool which if hot enough can melt plastic components or harm them. Keeping the heat source (heat gun) far enough away from the object that you’ll eventually melt the glue but would be much harder to melt components. I try to keep 4” or 5” gap between the source & object

    Sandman619 -

    Thanks for the info. Could a air convector do the job

    dominique.br - Contestar

    When opening a device that has previously been worked on, and on which the adhesive might not have been replaced, be extremely carful when opening the phone. It will open much more easily than expected. If you’re not careful you might rip a cable.

    jonpol - Contestar

    Is this tool required or can I just use the Anti-Clamp by itself.

    Mikail - Contestar

    If you have a 3d printer, heat the bed to 80c and put the phone screen side down on it for 30 secs

    philip.joseph123 - Contestar

  7. Reemplazo de las cámaras de cara posterior del iPhone X: paso 7, imagen 1 de 2 Reemplazo de las cámaras de cara posterior del iPhone X: paso 7, imagen 2 de 2
    • Si estás utilizando una sola ventosa, aplícala en el borde inferior del teléfono, evitando la porción curvada del cristal.

    If you were using some form of screen protector, it may come off first as soon as you pull on the suction cup. Do not be alarmed. That is normal behavior.

    Alain-Daniel Wa-Baguma - Contestar

    3m VSB double stick tape will stick to the screen when the suction cups fail (see my comment on step 1)

    Tawan Khamapirad - Contestar

  8. Reemplazo de las cámaras de cara posterior del iPhone X: paso 8, imagen 1 de 3 Reemplazo de las cámaras de cara posterior del iPhone X: paso 8, imagen 2 de 3 Reemplazo de las cámaras de cara posterior del iPhone X: paso 8, imagen 3 de 3
    • Tira de la ventosa con una presión firme y constante para crear un ligero hueco entre el panel frontal y la caja trasera.

    • Inserta una púa de apertura en el espacio debajo de la pantalla y el marco de plástico, no en la pantalla en sí.

    • El adhesivo impermeable que mantiene la pantalla en su lugar es muy fuerte; crear este hueco inicial requiere una cantidad significativa de fuerza. Si te cuesta abrir un hueco, aplica más calor y mueve suavemente la pantalla hacia arriba y hacia abajo para debilitar el adhesivo hasta que crees un hueco suficiente para insertar la herramienta.

    In addition to safety goggles, I would recommend you also wear good gloves to avoid getting cut with the glass as you try to pry it open.

    Alain-Daniel Wa-Baguma - Contestar

    The top about applying more heat and gently rocking the screen up and down to weaken the adhesive did the trick for me. Thank you!

    Monil Shah - Contestar

    There needs to be more clarity on where to shove the opening pick into. There is actually two openings that the pry tool can be forced into: one below the black plastic bezel, and one above the black plastic bezel. When I heated my screen with a warming pad and pulled up the suction cup, it actually pried apart above the black plastic bezel which removed the touch screen from the display panel. With this being the first newer iPhone I'd opened since the 3GS, I didn't realize that I was opening the wrong opening as the directions only mentioned one opening and did not warn of this. I was pretty disappointed in the lack of mentioning this, as I was taking my time and following it to the tee. As a result, it destroyed my original iPhone screen.

    Caleb Davison - Contestar

    DO NOT separate the glass from the plastic bumper or rim around it. As someone else noted, these instructions don't clarify that the pick has to be inserted between the plastic rim and the metal body of the phone. When pulling upwards with the suction cup, it is likely that the glass will lift slightly off the plastic surround before the plastic will lift out of the metal body. I had success sliding a card or pick back and forth along the bottom edge of the plastic rim while pulling on the suction cup. Eventually there was a space large enough for the pick to go under the plastic rim.

    Anessa - Contestar

    Thank you for pointing this out! I've updated the step to reflect this.

    Arthur Shi -

    The suction cup doesn't work at all... The minimum force I apply to lift it up, it comes off completely. This is very frustrating!!!

    Mario Silva - Contestar

  9. Reemplazo de las cámaras de cara posterior del iPhone X: paso 9, imagen 1 de 3 Reemplazo de las cámaras de cara posterior del iPhone X: paso 9, imagen 2 de 3 Reemplazo de las cámaras de cara posterior del iPhone X: paso 9, imagen 3 de 3
    • Desliza la púa de apertura por la esquina inferior izquierda y por el borde izquierdo del iPhone, cortando el adhesivo que mantiene la pantalla en su lugar.

    • No insertes tu púa más de 3 mm, ya que puedes dañar los componentes internos.

  10. Reemplazo de las cámaras de cara posterior del iPhone X, Información de la pantalla: paso 10, imagen 1 de 1
    • Hay cables delicados a lo largo del borde derecho de tu iPhone. No insertes tu púa aquí, ya que puedes dañar los cables.

    Wouldn’t it be better to put this part BEFORE the step where you have to pry open the phone?

    Jan D. Höllwarth - Contestar

  11. Reemplazo de las cámaras de cara posterior del iPhone X: paso 11, imagen 1 de 3 Reemplazo de las cámaras de cara posterior del iPhone X: paso 11, imagen 2 de 3 Reemplazo de las cámaras de cara posterior del iPhone X: paso 11, imagen 3 de 3
    • Re-inserta tu púa en el borde inferior del iPhone y deslízala a lo largo del lado derecho para continuar separando el adhesivo.

    • No insertes tu púa más de 3 mm, ya que puedes dañar los cables de la pantalla.

    If you have flat feeler gauges (for adjusting engine valve tappet clearance, ignition points … old school) the .003” thick gauge goes right in. Work your way up in thickness until you can get the pic or supplied pry tool in. Don’t insert metal feeler gauge in too far, just enough to hold crack open. I didn’t need to use the suction cup. I used a hot/cold gel pack heated in microwave to heat edges to soften glue a bit. Made sure it wasn’t so hot I couldn’t stand it on my skin.

    William Olstad - Contestar

  12. Reemplazo de las cámaras de cara posterior del iPhone X: paso 12, imagen 1 de 3 Reemplazo de las cámaras de cara posterior del iPhone X: paso 12, imagen 2 de 3 Reemplazo de las cámaras de cara posterior del iPhone X: paso 12, imagen 3 de 3
    • El borde superior de la pantalla está asegurado con pegamento y clips.

    • Desliza la púa de apertura alrededor de la esquina superior de la pantalla, mientras tiras suavemente o mueve la pantalla hacia abajo en la dirección del puerto Lightning.

    • Los clips se romperán si usas demasiada fuerza. Trabaja con cuidado y se paciente.

    • No insertes tu púa más de 3 mm, ya que puedes dañar el conjunto de sensores del panel frontal.

    • Desliza la púa hacia la esquina opuesta y corte cualquier adhesivo restante que asegure la pantalla.

    These are the best instructions I’ve ever read for anything.! Thank you!

    Peter Andrew - Contestar

  13. Reemplazo de las cámaras de cara posterior del iPhone X: paso 13, imagen 1 de 1
    • Tira de la pequeña protuberancia en la ventosa para remover el panel frontal.

  14. Reemplazo de las cámaras de cara posterior del iPhone X: paso 14, imagen 1 de 3 Reemplazo de las cámaras de cara posterior del iPhone X: paso 14, imagen 2 de 3 Reemplazo de las cámaras de cara posterior del iPhone X: paso 14, imagen 3 de 3
    • Abre el iPhone moviendo la pantalla hacia arriba desde el lado izquierdo, como si abrieras la contratapa de un libro.

    • No trates de separar completamente la pantalla aun ya que varios frágiles cables planos todavía la conectan con la placa lógica del iPhone.

    • Como se muestra, asegúrate de que el marco salga con la pantalla y no se quede atascado en el teléfono.

    • Apoya la pantalla contra algo para mantenerla en alto mientras trabajas con el teléfono.

    • Durante el ensamblado, alinea los clips a lo largo del borde superior y con cuidado presiona el borde superior en su lugar antes de encajar el resto de la pantalla. Si no se encaja fácilmente, verifica la condición de los clips alrededor del perímetro de la pantalla para asegurarte que no estén doblados.

    My phone came apart in a different way and looks not right the little box at the top of the display as actually bolted to the top of the frame body I think something went really wrong when I opened it.

    Mike Kostersitz - Contestar

    It opens like a book but be careful not to open it all the way — only as far as shown in the photo. Otherwise it will strain the thin cable that connects the sensor module and then no more FaceID for you (or, as it turns out me). This could have been made more explicit in the instructions.

    Richard Tucker - Contestar

    It opens like a book but be careful not to open it all the way  … the small stainless steel tabs that hold the screen around the metal frame, that are on the bend place (right side of the phone)… are tend to bend, you can straighten them back to 90 deg. but the plastic base that they are on? very fragile- watch out not to break the plastic bezel … it may come apart of the glass.

    dabur872 - Contestar

    Advice for re-assembly: Before closing up the phone with the seal, check if phone is powering up again and speaker, mic and sensors are still working. If done this check even before installing the board connector bracket in Step 13.

    Alexander Nowak - Contestar

  15. Reemplazo de las cámaras de cara posterior del iPhone X, Ensamblaje de pantalla: paso 15, imagen 1 de 1
    • Remueve los cinco tornillos Y000 que sujetan el soporte de conector de la placa lógica y que tienen los siguientes largos:

    • Tres tornillos de 1.1 mm

    • Un tornillo de 3.1 mm

    • Un tornillo de 3.7 mm

    • Durante esta reparación, lleva la cuenta de cada tornillo y asegúrate de que vaya exactamente al mismo lugar de donde salió para evitar dañar tu iPhone.

    One thing I found helpful for replacing the screws was to use only the 000screwdriver tip, without the handle. This way, the tip isn’t magnetized and the screw doesn’t tend to ‘roll’ off the screwdriver tip (the screw has almost no mass, so the head (largest surface) is pulled around to the side of the screwdriver tip when magnetized).

    Rich May 23, 2020

    ungodly - Contestar

    My 3.1mm screw had a stripped head, could not remove it. (Factory defect, this iPhone was never opened)

    So I had to give up removing the display assembly, and jumped directly to battery replacement, Step 20.

    That was tricky as I had to keep the display at 90º with a risk of breaking display connectors, but hopefully the replacement went well.

    I would not recommend to do this but to follow the guide, but, in case someone encounters a similar issue, that could help!

    vingu - Contestar

    My 1.1mm screw had a stripped head. Used a 3mm steel drill to cut the head off (just 1 mm deep haha) so i could remove the bracket.

    Renout - Contestar

    Be careful on reassembly. Keep the screen supported and not moving. I had difficulty getting the screws in and ended up ruining the screen connectivity at the back of the screen where the ribbon cables go in near the center. I was trying to hand hold the screen and it ended up moving around too much.

    SETH GREEN - Contestar

    To keep track of the screws, I copy the photos showing their places, then arrange these photos on document in Pages, print it. Next I apply two sided sticky tape (the roll-on type). So all screws have their corresponding places …

    Max Glanzmann - Contestar

  16. Reemplazo de las cámaras de cara posterior del iPhone X: paso 16, imagen 1 de 1
    • Remueve el soporte.

    • El soporte puede estar ligeramente adherido en su lugar. Levanta cuidadosamente para separarlo.

    • Durante el reensamblaje es un buen momento de encender tu iPhone para verificar las funciones antes de sellar la pantalla en su lugar. Asegúrate de apagar tu iPhone completamente antes de seguir trabajando.

    I tested it, then proceeded to close up the device without the bracket. Do I need to reopen and install? All connections are good?

    monastra7 - Contestar

    The bracket helps those many connectors underneath maintain good contact. Probably in the short term nothing bad will happen, but I’d hang onto the bracket and reinstall it when convenient.

    Jeff Suovanen -

    Agree with Jeff

    cgtyoder -

    I tested all imaginable functionality on the new OLED screen. Taptics are fine. Then, I noticed that the battery wasn't charging. Any ideas as to what could have gone wrong?

    Monica - Contestar

    for me, the replacement battery was completely dead, small panic when the power-on button was pressed, but quickly realised that this was the situation, and now watching the phone take a power cycle.

    James Stanbridge - Contestar

    Before clicking the screen assembly back, I tried to test the iPhone by pushing the start button, but nothing happened. After taking off the bracket, reseating the plugs I tried again - nothing happened! Then I plugged in the charging cable connected with the iMac, and it started immediately. So if the phone does not start using the startup button, it might just be a glitch when reconnecting the battery.

    Max Glanzmann - Contestar

  17. Reemplazo de las cámaras de cara posterior del iPhone X: paso 17, imagen 1 de 2 Reemplazo de las cámaras de cara posterior del iPhone X: paso 17, imagen 2 de 2
    • Usa la punta de un spudger o una uña para hacer palanca en el conector de la batería y levantarlo de su zócalo en la placa lógica.

    • Trata de no dañar el sello de silicona negra que rodea este y otras conexiones de placa. Estos sellos proporcionan protección adicional contra la entrada de agua y polvo.

    • Dobla el conector para separarlo de la placa lógica para prevenir que entre accidentalmente en contacto con el zócalo y que proporcione alimentación al teléfono durante la reparación.

    cosa può succedere se non si disconnette la scheda logica'?

    luca.valli - Contestar

    note: be careful not to crush or puncture your battery at this step!! I gave mine a minor dent, which I hope wont be a problem.. but something to keep in mind for fxlks in the future!

    Noal Balint - Contestar

    Thanks, already did it)

    Stephen Hedrick -

  18. Reemplazo de las cámaras de cara posterior del iPhone X: paso 18, imagen 1 de 2 Reemplazo de las cámaras de cara posterior del iPhone X: paso 18, imagen 2 de 2
    • Usa la punta de un spudger o una uña para desconectar el conector del ensamblaje del sensor del panel frontal.

  19. Reemplazo de las cámaras de cara posterior del iPhone X: paso 19, imagen 1 de 2 Reemplazo de las cámaras de cara posterior del iPhone X: paso 19, imagen 2 de 2
    • Usa la punta de un spudger o una uña para desconectar el conector de cable de panel OLED.

    • Para volver a colocar los conectores de prensa como este, alinea con cuidado y presiona hacia abajo en un lado hasta que encaje en su lugar, luego repite en el otro lado. No presiona hacia abajo en el medio. Si el conector está desalineado, los pasadores pueden doblarse, causando daños permanentes.

    Snap ‘em in like little Legos.

    Ray Johnson - Contestar

    Maybe the manual should flip step 17 and 18 (as the digitizer cable from 18, is in the way of the OLED cable of step 17) ?

    Renout - Contestar

  20. Reemplazo de las cámaras de cara posterior del iPhone X: paso 20, imagen 1 de 2 Reemplazo de las cámaras de cara posterior del iPhone X: paso 20, imagen 2 de 2
    • Usa la punta de un spudger para levantar el conector del cable de digitalizador de su zócalo.

    • La ubicación empotrada de este conector dificulta la reconexión. Tómate tu tiempo y alinéalo con cuidado, luego presiona suavemente en su lugar con la yema del dedo, primero un lado y luego el otro. Deberías sentir que hace clic en su lugar

    • Si alguna parte de tu pantalla no responde al tacto después de su reparación, desconecta la batería y vuelve a colocar el conector, asegurándote de que encaje completamente en su lugar y de que no haya polvo u otra obstrucción en el zócalo.

    This was probably the hardest part other than trying to get the screen off with the crappy suction cups. I re-installed the bracket only the find out that the touch screen would not respond to touch. Had to remove the five screws, remove the bracket and reseat the recessed screen connector. Reseating the bracket took another 10+ minutes. I carefully used the angled forceps to grab the cable and align the connector being careful not to damage the cable.

    Once you have the connector seated, I would reconnect the battery, power on the phone, and check the touch screen response before re-installing the bracket (step 13).

    Tawan Khamapirad - Contestar

    Yeah, this was probably the trickiest part of the reassembly. The power connector cable kept getting in the way so I moved it carefully but fully out of the way. Then it was a matter of fiddling around with it a bit and being careful not to force it on.

    Jeffrey Hoy -

    I was positive that I had messed something up, I had powered up the phone to test three different times and everything seemed find except there was no touch at all. On my fourth attempt, I carefully examined everything for dust and debris (blowing gently), and I did notice that a corner of the connector (more like part of the ribbon) was bent slightly, and I straightened it. I don't know if it was the ribbon or some tiny debris, but after reseating a fourth time, it worked.

    Pol Llovet - Contestar

    Very important part of the tutorial. Be careful and patience! In my case the screen and camera didn't respond after assemble, so I tried again to reconnect the connector like tutorial said and it worked well. Now my iPhone feel like a new one 💪🏼

    Efrain Maestre - Contestar

  21. Reemplazo de las cámaras de cara posterior del iPhone X: paso 21, imagen 1 de 3 Reemplazo de las cámaras de cara posterior del iPhone X: paso 21, imagen 2 de 3 Reemplazo de las cámaras de cara posterior del iPhone X: paso 21, imagen 3 de 3
    • El cable flexible de ensamblaje de sensor de panel frontal está adherido en su lugar.

    • Con cuidado levanta el cable hasta que el adhesivo se separe.

    Do this sensor affect face id?

    bonglkv - Contestar

    It is part of the face id part so yes. This is the ear piece too so if the ribbon tears there is a chance the ear piece will stop working as well.

    Stephen Patterson - Contestar

    Be super careful handling this ribbon particularly. I did a battery install and, when I was done, I had a phone with a new battery and no Face ID. That’s a $300 Apple repair, and no 3rd party shop will touch it. I believe the ribbon lays vertically (i.e., perpendicular to the “floor” of the phone, against the side edge of the battery. During the re-install, I must have forced the ribbon into position after seating the connector, causing fatal flexing of the ribbon. (Don’t know this for sure, but I see another comment saying that this cable is part of Face ID.) Anyway, bottom line: BE CAREFUL REMOVING AND REINSTALLING THIS RIBBON!

    Jonathan Pines - Contestar

    My flex cable was more than lightly adhered in place. I needed to use a guitar pic or similar to help encourage adhesive to separate. I wouldn’t pull too hard like shown in pictures unless you had just the right grip on the ribbon cable so as to avoid damaging flex cable. See note above (5/31/20)

    William Olstad - Contestar

    Bizarre — it turns out my whole front panel sensor assembly came entire off of the front screen and is stuck to the logic board.

    Karl Jarvis - Contestar

    I also found the glue quite recluctant to release so I applied a second or two of heat using the wife's hair dryer which softened it and the cable lifted much easier then. Be careful not to apply too much heat though which could then impact other internal components.

    LosBenitos - Contestar

    Cho ít cồn 90° vào để mềm keo dễ tháo

    huuhaukimngan - Contestar

    my iphone x doesn't have a front panel sensor? in fact, it looks completely different than the picture???

    Kenneth McLeod - Contestar

    @kennethmcleod, most likely you've separated the screen frame from the screen itself. We see this most commonly when people neglect to remove the pentalobe screws next to the charging port. Usually the cure is to take out those screws, then repeat the screen removal process on the frame that's still attached to the phone.

    Jerry Wheeler -

    You don't need to disconnect the front sensor to change the screen. Just leave it connected and remove from the screen side.

    Anthony Boshell - Contestar

  22. Reemplazo de las cámaras de cara posterior del iPhone X: paso 22, imagen 1 de 1

    I tried this and broke the cable can it still repair

    Alexis Rodriguez - Contestar

    At this point I would have found it easier to remove the glue from the edges than later on when I was reassembling it. I bought the kit that had the replacement glue in it.

    Grant - Contestar

    Excellent guide! Would love to have a link to moving the sensor assembly from the old display to the new here.

    Nicole - Contestar

    CAUTION:

    Removing the Taptic Engine or Speaker in next step is optional and the guide continues as this was per se needed.

    Unnecessary work and also If you remove the speaker you lose the adhesive gasket and this is not included in the scope of delivery of the "Battery replacement" offering.

    So do not remove and avoid losing waterproofing.

    Julian Gonzalez - Contestar

  23. Reemplazo de las cámaras de cara posterior del iPhone X, Cámaras Traseras: paso 23, imagen 1 de 1
    • Retira los dos tornillos Phillips que sujetan el soporte de la cámara, de las siguientes longitudes:

    • Un tornillo de 2.3 mm.

    • Un tornillo de 2.0 mm

  24. Reemplazo de las cámaras de cara posterior del iPhone X: paso 24, imagen 1 de 2 Reemplazo de las cámaras de cara posterior del iPhone X: paso 24, imagen 2 de 2
    • Usa unas pinzas para doblar suavemente el pequeño soporte de conexión a tierra de metal. No tires hacia arriba ya que está conectado a un cable flexible frágil.

    What is these cable for

    max Well - Contestar

  25. Reemplazo de las cámaras de cara posterior del iPhone X: paso 25, imagen 1 de 3 Reemplazo de las cámaras de cara posterior del iPhone X: paso 25, imagen 2 de 3 Reemplazo de las cámaras de cara posterior del iPhone X: paso 25, imagen 3 de 3
    • Levanta el soporte de la cámara desde el borde más cercano a la batería y extráelo.

    • Para volver a instalar el soporte de la cámara, sigue las imágenes exactamente al revés: primero, baja el borde exterior hasta que la pestaña de las ranuras del lado derecho quede dentro del espacio entre la caja del teléfono y el módulo de la cámara. Luego, gira el soporte hacia abajo sobre el módulo de la cámara.

  26. Reemplazo de las cámaras de cara posterior del iPhone X: paso 26, imagen 1 de 3 Reemplazo de las cámaras de cara posterior del iPhone X: paso 26, imagen 2 de 3 Reemplazo de las cámaras de cara posterior del iPhone X: paso 26, imagen 3 de 3
    • Usa una herramienta de apertura o una uña para desconectar los dos conectores de la cámara haciendo palanca hacia arriba desde sus enchufes.

  27. Reemplazo de las cámaras de cara posterior del iPhone X: paso 27, imagen 1 de 2 Reemplazo de las cámaras de cara posterior del iPhone X: paso 27, imagen 2 de 2
    • Presiona la punta de un spudger contra una pequeña muesca en la esquina inferior derecha del módulo de la cámara.

    • Haz palanca suavemente para sacar la cámara del iPhone.

  28. Reemplazo de las cámaras de cara posterior del iPhone X: paso 28, imagen 1 de 1
    • Retira el módulo de la cámara orientada hacia atrás.

Conclusión

Compara tu nueva pieza de repuesto con la pieza original; es posible que debas transferir los componentes restantes o quitar los respaldos adhesivos de la pieza nueva antes de instalarlos.

Para volver a montar tu dispositivo, sigue los pasos anteriores en orden inverso

Lleva tus desechos electrónicos a un centro de reciclaje certificado.

¿La reparación no salió según lo planeado? Consulta nuestra para obtener ayuda para la solución de problemas.

41 personas más completaron esta guía.

Un agradecimiento especial a estos traductores:

en es

100%

Estos traductores nos están ayudando a reparar el mundo! ¿Quieres contribuir?
Empezar a traducir ›

Adam O'Camb

Miembro Desde 04/11/15

195,318 Reputación

416 Guías creadas

2 comentarios

So in step 21 the grounding plate that sits on top of the bracket… which flex is that attached to? This X i’m working on was used for navigation on a motorcycle trip by my client and from that point on the rear came image was vibrating. I noticed this flex is torn but can’t identify the flex it came detached from. Hope someone knows so I don’t need to pull it apart to find out before gettinf the right parts in?! Many thanks in advance

Manus - Contestar

It’s bluetooth antena flex

Koriakinides -

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 19

Ultimos 7 días: 98

Ultimos 30 días: 489

Todo El Tiempo: 61,121