Introducción
Esta guía le llevará a través del proceso de instalación de la placa del botón izquierdo. Esta placa controla el pad direccional (D-pad) y el botón PS.
Qué necesitas
-
-
Usando un destornillador Phillips # 00, retire los cuatro tornillos de 6,4 mm en la carcasa trasera
-
-
-
Suavemente separar las dos carcasas, teniendo en cuenta la batería y los conectores del controlador de pantalla táctil que mantienen las carcasas juntas..
-
-
-
Libere el cable de la batería levantando suavemente la conexión con un spudger.
Any idea what type of pcb header is on the board for the battery? I have a motherboard with a broken header but I cant source a replacement
This is where I screwed up so I recommend extra caution for other newbies. Only the black part is supposed to come off. Don't be an idiot like me and pry off too much...
Yea I messed up there too. Is there a way to fix it?
This component was far more stubborn than the screen connector when it came to removal. I opted for a smaller tool than the spudger (small flat-head) and managed to disconnect it after determining the best bit size for the job. Screwdriver is metal, obviously, so being gentle helps to avoid damaging anything.
broke the white part
-
-
-
-
Levante la cubierta del botón del hombro izquierdo con un spudger.
-
Retire la carcasa del botón del hombro izquierdo.
-
-
-
Suelte el zócalo del cable flexible del botón del hombro izquierdo usando un spudger para abrir la lengüeta.
-
Con las pinzas, deslice el cable flexible del zócalo. ¡No tire de la lengüeta negra! En su lugar, tire del cable delgado flex de distancia del conector (a la izquierda en esta imagen).
-
-
-
Usando un spudger, levante suavemente el botón del hombro izquierdo del adhesivo ligero que lo conecta a la carcasa.
-
-
-
Usando un spudger, levante y suelte la lengüeta en el zócalo ZIF sentado en el lector de tarjetas SIM.
-
Extraiga con cuidado el cable flexible del zócalo ZIF y déjelo fuera del camino.
Este paso NO es necesario si tu PSVita no tiene lector de tarjeta SIM. Ve directamente al paso 15.
-
-
-
Usando un destornillador Phillips # 00, retire los seis tornillos de los dos soportes metálicos:
-
Dos tornillos de 5,0 mm, azules en el soporte en L que aseguran la placa superior izquierda del botón a la placa base.
-
Cuatro 5,0 mm, tornillos azules en el soporte cuadrado de fijación de la placa del botón izquierdo inferior a la placa base.
-
Para volver a armar el dispositivo, siga estas instrucciones en orden inverso.
Para volver a armar el dispositivo, siga estas instrucciones en orden inverso.
Cancelar: No complete esta guía.
6 personas más completaron esta guía.
Un agradecimiento especial a estos traductores:
100%
Estos traductores nos están ayudando a reparar el mundo! ¿Quieres contribuir?
Empezar a traducir ›
3 comentarios
good idea but i need help with the big fat one on the left because it went into water by an accsident and its not moving and its like locked or like jammed. I put it in the boiler for a while and i took it out after then it still was jammed locked.
please can you tell me how to fix the big fat button on the left because water went in it and i tryed putting it in the boiler for a while then i took it out and the button was still not working it like jammed locked it dosn't work. PLEEEEEEAAAAASSSSEEE HEEELLLPPP MEEEEEE!!!!!!!!!!!!!!!!!!
Make a video of it please!!!!