Introducción
Usa esta guía para reemplazar la placa de carga en tu Huawei P10 Lite. Al volver a ensamblar tu teléfono, aplica adhesivo nuevo donde sea necesario.
Qué necesitas
-
-
Introduce la punta de una púa de apertura entre la tapa trasera y el marco medio y deslízala alrededor del teléfono para cortar el adhesivo.
-
Usar un mango de succión para levantar la carcasa trasera podría ayudarte a generar un poco de espacio donde insertar la púa de apertura.
-
-
-
Usa un par de pinzas para remover el sticker.
-
Remueve los dos tornillos Phillips #00
-
Remueve los cuatro tornillos Phillips de 2.5 mm.
Schritt 3 und 4 kann man sich komplett sparen. Wozu auch. Kann gleich mit Schritt 5 weitergemacht werden, zuvor einfach das Flachbandkabel vom Fingerabdrucksensor an der Rückabdeckung abklemmen und fertig.
Translate what Bobby mcgee said:
Step 3 and 4 can be completely ignored. What for? You can continue with step 5, just disconnect the ribbon cable from the fingerprint sensor on the back cover and you're done.
However, the reason step 3 and 4 should not be skipped is Step 6 — Use an iOpener to loosen the adhesive beneath the battery. I.e., the adhesive cannot be easily removed without heat, however, that heat might damage the electric chips. Thus they’d better be removed first.
-
-
-
Usa una pinza para remover el escudo de la placa madre.
-
Usa un extremo plano de un spudger para desconectar el cable flexible de sensor de huella digital.
Welchen Klebstoff soll man verwenden?
Hallo Josef,
sollte bei deinem Ersatzteil kein Klebstoff oder Klebeband dabei gewesen sein, kannst du dünne Streifen Doppelseitiges Klebeband verwenden. Es gibt für das Huawei P10 Lite auch schon zugeschnittene Klebestreifen zu erwerben, hierbei gilt aber je nach Händler Rezessionen zu lesen, ob die Klebestreifen auch wirklich halten.
Hi darren,
pre-cut adhesive would be the best solution if you can source it. Otherwise a two-sided adhesive tape or carefully used E6000 adhesive glue will be your friend. -
-
-
-
Remueve el tornillo Phillips #00 .
-
Remueve la placa del conector de la batería.
-
Usa un extremo plano de un spudger para desconectar el cable flexible de batería.
-
-
-
Usa el extremo plano de un spudger para desconectar el cable de interconexión.
-
Usa pinzas para desconectar el cable de la antena.
-
Para volver a ensamblar tu dispositivo, sigue estas instrucciones en orden inverso. Al volver a ensamblar tu teléfono, aplica adhesivo nuevo donde sea necesario.
Para volver a ensamblar tu dispositivo, sigue estas instrucciones en orden inverso. Al volver a ensamblar tu teléfono, aplica adhesivo nuevo donde sea necesario.
Cancelar: No complete esta guía.
5 personas más completaron esta guía.
Un agradecimiento especial a estos traductores:
100%
¡ Mariana Roca nos está ayudando a reparar el mundo! ¿Quieres contribuir?
Empezar a traducir ›
Mit dem Saugnapf die Rückseite anheben hilft ungemein…
Matthias Eberle - Contestar
Had to use blue wedge tool to wedge open bottom plate from the rim part in order to then use the tip of the blue opening pick under the back plate to then cut the glue. It’s like placing a pie server or knife under the plate once there’s a gap between the rim and the back plate.
Jane - Contestar
Be careful, there’s a cable to fingerprint sensor, very close to the edge (see pictures below)… It’s very easy to cut it through with the pick, as I just learned :)
dambig - Contestar