Esta traducción podría no reflejar los cambios más recientes añadidos a la guía de referencia. Ayúdanos a actualizar la traducción o revisa la guía original.
Introducción
Usa esta guía para quitar o reemplazar la pantalla y el sensor de huellas digitales de tu Motorola Moto Z2 Force. El sensor de huellas digitales del Z2 Force es muy difícil de separar del ensamblaje de la pantalla, así que si necesitas reemplazarlo, probablemente debas reemplazar todo el ensamblaje de la pantalla.
Advertencia: El ensamblaje de la pantalla de este dispositivo está compuesto por un marco medio rígido y una pantalla de plástico flexible que se puede separar durante el desmontaje. El calor excesivo en la pantalla también puede causar que burbujee o se deforme, y esto es muy difícil de remediar. Si planea reutilizar el ensamblaje de la pantalla, preste atención a todas las advertencias y ten cuidado de no sobrecalentar la pantalla.
Qué necesitas
-
-
Apaga el teléfono antes de comenzar.
-
Si es posible, drena la batería antes del desmontaje. Cuando la batería esté cargada, hay un aumento en el riesgo de un evento térmico peligroso si la batería se sobrecalienta o daña durante la reparación.
-
Prepara un iOpener y calienta la parte delantera del teléfono a lo largo de su borde inferior durante unos dos minutos, o hasta que esté ligeramente demasiado caliente para tocarlo. Esto ayudará a suavizar el adhesivo que asegura el montaje de la pantalla.
-
-
-
Aplica una ventosa en el borde derecho de la pantalla lo más cerca posible de la parte inferior del dispositivo sin superponer el sensor de huellas digitales.
-
Tira de la ventosa con una presión firme y constante para crear un ligero hueco a lo largo del borde inferior entre el ensamblaje de la pantalla y la caja trasera.
-
Esto puede requerir una cantidad significativa de fuerza, pero sólo necesita abrir un pequeño espacio con la ventosa para insertar su herramienta.
-
Inserta una púa de apertura en el zócalo que abrió detrás del ensamblaje de la pantalla.
No — *slaps wrist* No. Bad steps! Don’t use the suction cup at all, ever. It causes the two layers to separate immediately, long before the frame clips give way to let the screen come off.
I’m being super ultra very careful with this second attempt on a new device (that was in pretty pristine condition, if I can keep it that way!), and right when I tried pulling as instructed, the screen layers started to pull apart. Use a blade shoved into the edge of the phone and pry it apart, releasing the latches in the process!
I have to agree with Matt above. At the smallest bit of pressure on the suction cup, the screen de-laminated from the metal base. It still “works”, but….
None of the tools in the kit is terribly suited for getting in there and prying that clip apart without splitting the screen.
lease Read the Comments poste on “STEP 2”, When you apply the heat, the screen becomes unglued from the metal fram that it is attached to. I ended up damaging my screen. You need to make sure that what is coming unglued is the metal, and not just the plastic screen. I found out when I saw another video, where they do not apply heat, they just use a tool to pry the frame-display assembly… But apparently it was too late… You should be more specific about the warning…
A jimmy does not come with the kit. Buy one before beginning this procedure. It is the best way to lift the screen assembly without damaging the assembly.
This whole guide has been rewritten since my last comment, and I super appreciate it. The steps are now much more appropriate and less likely to cause damage. Jamming your Jimmy (huehue) into the edge of the screen is actually quite a good idea, not likely to hit anything as there’s nothing but body underneath it.
-
-
-
Retira la pantalla tirando de derecha a izquierda y colocando la pantalla boca abajo sobre la superficie plana al lado del cuerpo principal del dispositivo.
-
Deja tu herramienta aquí debajo del borde inferior del ensamblaje de la pantalla para evitar que se vuelva a adherir al marco. Continúa con el siguiente paso con una nueva herramienta.
-
-
-
Al separar el ensamblaje de la pantalla del resto del dispositivo, tendrás que desenganchar cinco clips metálicos que lo sujetan al marco del dispositivo.
-
Tres de estos clips están situados en el lado izquierdo del dispositivo, y dos en el lado derecho.
-
Necesitarás trabajar alrededor de estos clips con tu herramienta para poder desengancharlos completamente.
-
Puedes deslizar la herramienta cuidadosamente alrededor de estos clips, o dejar una púa en un lado del clip mientras que haces palanca en el otro lado con otra púa.
-
-
-
Desliza tu herramienta a lo largo del lado derecho del dispositivo para liberar los clips y el adhesivo que asegura el ensamblaje de la pantalla.
this is really for the digitizer and screen replacement. there are still more steps for just the screen.
There is an enormous amount of adhesive sticking this thing together. As the adhesive is not essential (it holds together with clips, mostly), you really need to focus on *removing* the adhesive, so that it doesn’t stretch and bunch-up, preventing clean reassembly. Leave behind the adhesive that you can prevent from bunching-up (by cleanly breaking it, in turn by holding down one edge to the phone or screen), so you have some sticky left, but just make sure it’s not bunched-up.
Revisiting this comment a year later: there’s now replacement adhesive available (or maybe there always was - wish I knew!) for this model in the iFixit store. So, it would be best to remove the adhesive whereever you see it, cleaning everything up and preparing for the new adhesive. That darn adhesive in step 9 below, though… ugh. Work slow, don’t expect it to all be apart by this point.
-
-
-
-
Hay dos grandes almohadillas de adhesivo que aseguran el ensamblaje de la pantalla cerca del borde superior pero más allá de los 4 mm que ya han sido cortados.
-
El ensamblaje de sensores frontales y el cable rodean el parche de adhesivo de la parte superior y derecha, por lo que si se fisgonea o se corta desde el borde superior o derecho se puede dañar el cable. Los siguientes pasos describirán cómo separar el adhesivo del borde izquierdo.
This is a tricky part. See the biggest red-squared section in the photo above? That part always wants to detach — the adhesive to the screen is stronger than the molding that holds the metal into the plastic. The metal will detach from the plastic pretty easily, and there’s no way to get that metal back into the plastic frame (as it seems to have been molded as a single part). So, the adhesive is a booby-trap.
To defuse the booby-trap, heat the heck out of it, insert one end of tweezers (or perhaps a spudger) from the right side, hold the metal plate down, and verrry slooowwly convince the adhesive to separate. At some point, it’ll start cascading and snap free.
The metal finger area, between the two red squared sections above, also is a problem area — it’s latched into a frame above the battery, and those latches can get pulled up on top of the frame, preventing the phone from reassembling clean and flat. Make sure to re-insert those tabs so that little edge with the metal fingers sits flat and proper.
-
-
-
Inserta un pico de apertura lo más profundo posible bajo la esquina izquierda de la pantalla para cortar a través del parche izquierdo de adhesivo.
I found that a plastic card inserted from the left side, and worked with a sawing motion, between the screen and the adhesive worked great after the adhesive was softened by the alcohol.
-
-
-
Desliza lenta y cuidadosamente el extremo plano de un spudger bajo el borde izquierdo del dispositivo. Poco a poco, introdúcelo más profundamente para levantar el borde superior del ensamblaje de la pantalla y libera el parche adhesivo derecho.
-
Recalienta el adhesivo para ablandarlo lo que sea necesario.
Again, pay careful attention to the strong block of adhesive sticking the display to a metal shield that’s molded into the plastic frame - the adhesive strength is quite likely to pull out the metal shield from the plastic frame and there’s no going back from that. Not as catastrophic as ripping a ribbon cable, but still pretty bad. See my comment a couple photos up about that.
I added some alcohol directly to the adhesive patches on this side of the phone and waited a couple of minutes before continuing with this step.
-
-
-
Si el ensamblaje de pantalla se atasca, vuelve a calentar y cortar el adhesivo repetidamente cuanto sea necesario.
-
Levanta el ensamblaje de pantalla del borde derecho y levántalo alejándolo del teléfono. Está todavía conectado al chasis del teléfono del borde izquierdo infierno, así que no lo remuevas completamente aun.
Do this only after slicing all the little ribbons of adhesive that hang around - and clean up any gummed-up, bunched-up strands of adhesive after removing it. I worked at detaching adhesive until the screen was totally free, only held by the ribbon cable, before moving on from this step.
-
-
-
Usa un par de pinzas para remover el trozo negro de la cinta que cubre el conector de la batería.
-
-
-
Usa un spudger para levantar la pestaña de bloqueo en el conector ZIF del cable de pantalla.
-
Desliza el cable plano de su conector.
-
-
-
Remueve el ensamblaje de pantalla.
When reconnecting the display ribbon I found it much easier if you straighten out major 45/90 degree bend that is in the middle of the ribbon until the entire ribbon is all unbent and in parallel with the display face. You will then have a straight shot into the connector without having to hold the display at a 90 degree angle to the chassis and then having to look around, over or through the display to (and if luck is with you) find, lineup and insert the ribbon into the connector. You have to do a little in 3 dimensional thinking to re-bend the ribbon and line the display back up with the chassis but if you’ve made it that far then you should have no problems. Don’t bend the ribbon back and forth too many times.
-
Compara la nueva parte de repuesto con la original; es posible que tengas que transferir los componentes restantes o retirar los respaldos adhesivos de la nueva pieza antes de instalarla.
Para volver a montar tu dispositivo, sigue los pasos anteriores en orden inverso
Lleva tus desechos electrónicos a un centro de reciclaje certificado.
¿La reparación no salió según lo planeado? Consulta nuestra comunidad de respuestas para obtener ayuda en la resolución de problemas.
Compara la nueva parte de repuesto con la original; es posible que tengas que transferir los componentes restantes o retirar los respaldos adhesivos de la nueva pieza antes de instalarla.
Para volver a montar tu dispositivo, sigue los pasos anteriores en orden inverso
Lleva tus desechos electrónicos a un centro de reciclaje certificado.
¿La reparación no salió según lo planeado? Consulta nuestra comunidad de respuestas para obtener ayuda en la resolución de problemas.
Cancelar: No complete esta guía.
17 personas más completaron esta guía.
Un agradecimiento especial a estos traductores:
48%
¡ Mariana Roca nos está ayudando a reparar el mundo! ¿Quieres contribuir?
Empezar a traducir ›
14 comentarios
lol exactly what i was thinking, john!!
like what the !&&*….guide us thru removing the entire screen and then just leave us with our d in our hand lol
Just do the same thing backwards.
Can I use a z2 play screen on the z2 force?
You can but they have a big difference the LCD pixelation. The Z2 Force has 2,560x1,440 pixel resolution while the play has a 1,920x1,080 resolution. So even thought it can be done it is not recommended.
Hello!
Where can I buy Z2 force screen?
I replaced the screen and now the touch is not working. Is there anything I need to know? I tried putting kapton tape around the digi IC Chip and that didn’t work.
Same problem!
Where is the best place to buy a Motorola Z2 Force LCD+Digitizer screen?
Buy a “bad IMEI” phone on eBay. They can’t be activated, but the screen is just fine. I just picked one up for $40 to replace my damaged screen (when I was following a previous version of this guide) - less than half the asking price for an LCD+digitizer alone. It also gives you more experience and a full set of replacement parts (except a motherboard which contains the bad IMEI).
Will this void my warranty or make my insurance deductible higher? My screen is flickering- and I am imagining that perhaps the ribbons need to be unplugged/dusted etc. Do you guys think its worth trying? My thinking is… right now I have to pay $120 for the deductable so why not try to fix it. My fear is- they will auto charge my account for the entire phone.
My Z Force 2 is showing a black screen, but I can tell it’s not dead. I tried the online suggestions of holding the power button down for 30 seconds (it cycles through the “restart” sequence, with all of the attendant sounds, but no visuals), and the second tier suggestion of holding down the power button while also holding down the volume button in the decrease volume position. No luck with that either. Now, even though I’m no longer messing with it, every so often it makes a little buzzing sound, with a bit of vibration, like it’s trying to come back to life. So, first of all, I don’t know if I need to replace the “display and fingerprint sensor” (is that the correct diagnosis?) or is something else at fault, and how would one tell? Secondly, if this IS the correct diagnosis, then there’s the problem of trying to power off the phone, while having no access to the display. And, I’m not sure I can drain the battery, but would taking it out suffice? Finally, do you think my phone repairable? Thx, Gigi
My phone screen went dead, however the touchscreen and fingerprint is still working. Is there any way to test wether it’s the mainboard or screen that’s defective? my phone took some water damage, I flushed it with 99% isopropanol and dried it with rice, however after a while the display first started to display afterimages before giving up entirely… any ideas? I’d rather not replace screen and motherboard.
Can a bad screen short out the phone? I replaced my screen assembly but when I plug in the new screen the phone won’t boot and make any booting noises, but when I unhook the screen assembly it boots and makes all the start up noises? Or could a pin be bent on the screen assembly connector?
