Introducción
Usa esta guía para quitar y reemplazar una batería agotada o baja en un Motorola Moto Z2 Play. Si tu batería está hinchada, toma las precauciones adecuadas.
Antes de comenzar, descarga la aplicación Rescue and Smart Assistant para hacer una copia de seguridad de tu dispositivo y diagnosticar si tu problema está relacionado con el software o el hardware.
Advertencia: debido al fuerte adhesivo que sujeta la pantalla, el espacio libre mínimo para insertar las herramientas y el alto nivel de calor requerido, existe una gran posibilidad de dañar accidentalmente la pantalla al retirarla. Si tienes la intención de reutilizar la pantalla, ten mucho cuidado al calentar e insertar herramientas para separar la pantalla del resto del dispositivo.
Qué necesitas
-
-
Apaga tu teléfono antes de completar cualquier paso de reemplazo.
-
-
-
Calienta los bordes de tu pantalla durante dos o tres minutos con una pistola de calor. Ajusta la pistola térmica a 85 grados centígrados, y ten cuidado de no mantenerla en una posición durante mucho tiempo; para evitar dañar la LCD. La pantalla debe estar muy caliente, pero no debe ser dolorosa al tacto. Vuelve a calentarla si es necesario.
-
-
-
-
Remueve la cinta naranja ubicada en la parte inferior derecha del teléfono utilizando pinzas.
-
-
-
Separa el cable negro y rojo de la batería levantando con pinzas.
What if the whole black box came off. I think i broke it! :( is this fixable?
-
-
-
Levanta para remover la batería completamente del dispositivo.
Why can't they just go back to the phones where you can snap off the back and simply replace the battery? I'm afraid to do it myself and Verizon won't do it for me. Now I have to find someone whom I will have to pay to replace a battery. This is ridiculous. It should not be so difficult to replace a battery and I should not have to jeopardize my phone to replace a battery. Why? Sorry, I just needed to vent. I miss simplicity.
I agree
I agree with both of you guys, but it’s the breaking point between performance, convenience, and safety. Older phones had batteries with hard protective casings that wouldn’t leave them vulnerable to pocket-fire if your keys jammed the battery.
Unfortunately, with phones getting more powerful(requiring a higher-capacity battery), AND slimmer, the protective casing for the battery is literally the casing on the phone. Look at the battery above; it could easily be pierced and dangerously vent.
I’m with you in wishing I could just pop a spare in, but those days have passed. =/
I suggest NOT to do this. Followed the directions exactly, with the slight deviation of my cable into the battery crumbling so I carefully pulled out the lose pieces with the tweezers and had NO problem putting it back together. My phone was WORKING with the exploded, puffy battery with NO deficits. Now? No charging (but checked it with the multi-meter so I know it is not the fault of the new battery). Only reaction I get is the phone making a vibrating sound when I plug it in to charge. Will NOT turn on. Will NOT react. F*CKED.
Without knowing what I was getting into I ordered a replacement battery, toolkit, and screen adhesive. Thanks to this guide I was actually able to remove the screen, replace the battery, and get it sealed back up relatively easily. Definitely nerve-wracking as I haven’t attempted anything like this before, but my phone was at the end of the battery life so I figured why not give it a shot.
Thank you for the easy instructions!
i followed the guide step by step, but unfortunately i touched the lcd in one place ... with the result that the screen went KO can i fix it somehow?
-
Para volver a ensamblar tu dispositivo, sigue estas instrucciones en orden inverso.
Luego de completar esta guía, calibra tu batería recién instalada.
Para volver a ensamblar tu dispositivo, sigue estas instrucciones en orden inverso.
Luego de completar esta guía, calibra tu batería recién instalada.
Cancelar: No complete esta guía.
37 personas más completaron esta guía.
Un agradecimiento especial a estos traductores:
100%
Estos traductores nos están ayudando a reparar el mundo! ¿Quieres contribuir?
Empezar a traducir ›
11 comentarios
Great instructions, clear and concise.
thank you
so now that I've heated the adhesive to get the screen off do I need to apply new adhesive? or simply reheat it?
Hi Eli,
The most ideal option would be to replace the adhesive. This ensures the best chance for your phone to stay sealed. You can re-use the existing adhesive and it may work well enough for awhile.
Pretty good guide altogether. The only thing I’d add is some more detail on the heating phase, as far as temperature, adhesive depth, strength etc. Don’t want someone putting a heatgun on max temp and using it on their screen for 3 mins, ya know?
Thanks for making it really straightforward though.
Total fail. Used an iOpener but could not judge how hot it needed to be to soften the adhesive nor how firmly it can be pried/pulled without damage. Ended up with multiple internal cracks in the screen. Tried finishing the repair anyway, couldn’t tell how far the flat-flex cables needed to be inserted into their sockets to make a good connection. Pix in the guide are not clear enough to tell, and I neglected to take my own photos.
Oh well, so much for repair. Kid got a new phone out of the deal, the Z2P is headed for the landfill.
Finished the guide , battery works well, only problem I encoutered was my own hastines with prying the screen out. On the right side near the fingerprint sensor i went too deep with the pryer and tore the flex cable. Now I am waiting for the new one. So I’ll update when it comes and I change it.
Can the battery be replaced with a larger one or is it too tight.
Great guide - thank you 😊