Esta traducción podría no reflejar los cambios más recientes añadidos a la guía de referencia. Ayúdanos a actualizar la traducción o revisa la guía original.
Introducción
En esta guía te mostramos cómo remover y reemplazar el ensamblaje de pantalla con marco en tu Huawei P10.
Para proteger tus ojos de trozos de vidrio y poder sujetar mejor el teléfono para abrirlo tendrás que aplicar más cinta en la pantalla.
Cuando vuelvas a ensamblar tu teléfono, aplica adhesivo nuevo donde sea necesario. Antes de volver a ensamblar, verifica si en tu parte nueva hay algún componente que necesites transferir de la parte antigua.
Qué necesitas
-
-
Apaga el teléfono.
-
Quita los dos tornillos Pentalobe P2 en la parte inferior.
-
Quita la bandeja de tarjeta SIM.
-
-
-
Introduce una herramienta de apertura de plástico entre la pantalla y la carcasa comenzando en la parte inferior de tu teléfono.
-
Levanta con cuidado la pantalla con sus partes fuera de la carcasa.
-
Después de hacer palanca en el extremo inferior, usa la herramienta de apertura para abrir las abrazaderas en ambos lados.
Hi! I cannot find a way to insert the plastic opening tool. Any suggestions on how I can create a gap to start. Everything seems quit rigid.
Also, where will I find your reply.
vbr/lars.skoldebring@gmail.com
Hi Lars, you might want to use a suction handle to lift the display and create a small gap to insert the plastic tool. If you don’t have a suction handle you can “build” a handle with tape that you stick onto the display in a shape similar to this —> __∏__ (also you may want to edit your post and remove your email address ;) )
Hi,
I’m stuck at this step for about two hours… There’s nothing I can do to open the case. Tried all kinds of opening tools and a suction handle. There is no gap at all between the display and the body. How can anything be inserted into a gap that practically does not exist? Please help.
Sorry to hear that. You could try and lift the display by using a suction cup and pull to create a small gap for a tool to get in.
-
-
-
Abre el teléfono hacia atrás.
-
Usa un spudger para desconectar el cable flexible del botón de volumen y encendido.
Thanks JaL, of course it is.
-
-
-
Remover los dos tornillos Phillips #00.
-
-
-
-
Despega la tira adhesiva que está por debajo de la batería tirando de manera uniforme la lengüeta en un ángulo plano.
-
Usa un iOpener para ablandar el adhesivo restante
It wasn’t easy to find the piece to pull. It was a black label, folded and stuck to the battery
-
-
-
Remueve los cuatro tornillos Phillips #00 .
-
Usa las pinzas para remover la lámina de metal que cubre la placa de carga y el cable flexible principal.
-
-
-
Usa el extremo puntiagudo de un spudger en la esquina de derecha superior de la placa madre y haz palanca haste que puedas sujetar bien.
-
Remueve la placa madre.
Can I replace the pink thermal pad with thermal paste? Because I can't any online store sell pink thermal paste for phone.
-
Para volver a ensamblar tu dispositivo, sigue estas instrucciones en orden inverso. Cuando vuelvas a ensamblar, aplica adhesivo nuevo donde sea necesario.
Para volver a ensamblar tu dispositivo, sigue estas instrucciones en orden inverso. Cuando vuelvas a ensamblar, aplica adhesivo nuevo donde sea necesario.
Cancelar: No complete esta guía.
25 personas más completaron esta guía.
Un agradecimiento especial a estos traductores:
84%
¡ Mariana Roca nos está ayudando a reparar el mundo! ¿Quieres contribuir?
Empezar a traducir ›
5 comentarios
Are the pink/purple blobs unter the motherboard thermal paste? If so, should I re-apply any when reassembling?
The answer might come to late, as you most likely finished the repair in the last 5 years, but it might still be useful for others:
Yes, the purple blobs under the mainboard are thermal paste.
If the paste is still soft you could potentially reuse it but I would highly recommend to use some new thermal paste.
Gonna upload an easy and faster way to do it whitout removibg the battery or upper boards and cameras, wait for it, my 1st guide.
I didn’t add the tape. I don’t know why the battery comes with it, plus, it is ultra strong, I was all the time afraid to ruin the battery, but fortunatly, everything went well
Das Honor 9 hat an der Unterkante keine Schrauben.
Wie ist das Honor 9 zu öffnen?
Michael Tuschek - Contestar
Vielleicht beantwortet diese Anleitung deine Frage ;)
Tobias Isakeit -
Hi, my P10 does not have screws, just two tiny holes. Do I push in here to unfasten? Einar, Norway
Einar Ryvarden - Contestar
Hi Einar Ryvarden,
in case you bought a used or refurbished phone, someone might have forgotten to put them back in. Since you have holes at the bottom edge next to the charging port this is likely. You can try to start with step 2 and see if you can lift the phone assembly (don’t forget to remove the SIM tray first). As far as I know there is no version of the regular Huawei P10 with no screws. However you there are none in the P10 lite and in the P10 plus, maybe one of the opening procedures for those phones might help you.
Dominik Schnabelrauch -