Qué necesitas
-
-
Deslice los pestillos de liberación de la batería izquierda y derecha a la posición de desbloqueo.
-
-
-
Presione la TarjetaExpress para liberarla de la computadora.
-
-
-
Presione el teclado hacia abajo. Haga palanca en el teclado con el uso de un destornillador de punta plana hacia la pantalla para revelar el primer retenedor del teclado.
-
-
-
Suelte el pestillo del conector de la placa del sistema, luego desconecte el cable del teclado.
It is also required to loose the screw just beside the latch mentioned in this step.
-
-
-
Levante la puerta de la memoria cerca del orificio del tornillo, levántela y retírela.
-
-
-
Saque suavemente la unidad óptica de la computadora.
Make sure you have loosen the screw beside the keyboard cable latch, mentioned in the comments of Step 8.
-
-
-
Retire los tornillos que aseguran el soporte de la unidad óptica.
-
-
-
Retire el soporte de la unidad óptica del módulo de la unidad óptica.
-
-
-
Retire los tornillos en el compartimento de la unidad óptica.
-
-
-
-
Voltee la computadora y retire los tornillos que sujetan el reposamanos.
-
-
-
Suelte los pestillos del conector de la placa del sistema, luego desconecte el cable de la superficie táctil y el cable de la impresora digital.
-
-
-
Suelte el pestillo del conector de la placa del sistema y luego desconecte el cable del botón de encendido.
-
-
-
Suelte el pestillo del conector de la placa del sistema y luego desconecte el cable de la tecla de acceso rápido.
-
-
-
Levanta el lado derecho del reposamanos.
There are a couple of latches on the front of the palm rest which should be released before you move on to the sides. I think one of those latches is released in the picture above. The iFixit opening tool was helpful here, and I used some of the iFixit opening picks to stop the corner latches from closing while I worked on others.
-
-
-
Retire los tornillos que aseguran la cubierta de la bisagra.
You can skip this step, and others related to removing the display, because removing the display isn’t strictly necessary.
Con of removing the display:
o It takes time
Pros of removing the display:
o It makes it a little easier to remove the VGA card
o The computer will tip with the weight of the display when you remove other components.
-
-
-
Voltee la computadora y retire la cubierta de la bisagra del costado.
-
-
-
Afloje el tornillo que fija el cable de señalización diferencial de bajo voltaje (LVDS).
-
-
-
Desconectar el cable LVDS
By pulling it upwards?
-
-
-
Desconecte el cable de antena de la red de área local inalámbrica (WLAN).
-
-
-
Levante el ensamblaje de la pantalla y retírelo de la computadora.
-
-
-
Retire el tornillo que fija la tarjeta WLAN.
-
-
-
Extraiga la tarjeta WLAN de su zócalo y extráigala.
You can skip this step, it isn’t strictly necessary.
Cons of removing the WLAN card:
o I found the screw in the last step very stubborn, worried about stripping it.
o Takes time.
Pros of removing the WLAN card:
o Might make disconnecting the system board a little easier later. I had no trouble with the WLAN card in place though.
-
-
-
Suelte el pestillo de la placa del sistema y luego desconecte el cable VGA.
-
-
-
Retire la placa de VGA del chasis.
If you decided to leave the display in place, you can just loosen the screw on the VGA board, and leave the board itself where it is. The board blocks access to a screw securing the system fan, but once you’ve removed the screw from the VGA board you can just push the VGA board out of the way and remove the system fan screw. Of course, this means the VGA board can move around while you’re working on the rest of the computer, but I didn’t find that was a big problem. You could temporarily reinstall the VGA board screw after you’ve removed the system fan.
-
-
-
Desconecte el cable del ventilador del sistema de la placa base.
-
-
-
Retire el ventilador del sistema del módulo base inferior.
-
-
-
Desconecte el conector del cable de entrada de CC de la placa base.
-
-
-
Desconecte el cable del altavoz de la placa base.
-
-
-
Desconecte la placa del sistema del panel de Entrada / Salida.
-
Para volver a armar su dispositivo, siga estas instrucciones en orden inverso.
Para volver a armar su dispositivo, siga estas instrucciones en orden inverso.
Cancelar: No complete esta guía.
4 personas más completaron esta guía.
Un agradecimiento especial a estos traductores:
100%
¡ Daniel Morales Garcia nos está ayudando a reparar el mundo! ¿Quieres contribuir?
Empezar a traducir ›
4 comentarios
Who the !&&* designs a hard drive location that requires complete disassembly of the motherboard and the laptop to replace. Horrible, horrible design.