Saltar al contenido principal

Introducción

Sigue los pasos en esta guía para reemplazar la cámara trasera iSight en tu iPhone 6s Plus.

Resumen del Video

  1. Antes de desarmar su iPhone, descarga la batería por debajo del 25%. Una batería de litio-ion cargada puede incendiarse y / o explotar si se pincha accidentalmente.
    • Antes de desarmar su iPhone, descarga la batería por debajo del 25%. Una batería de litio-ion cargada puede incendiarse y / o explotar si se pincha accidentalmente.

    • Apaga su iPhone antes de comenzar el desensamblaje.

    • Retira los dos tornillos Pentalobe de 3.4 mm a ambos lados del puerto Lightning.

    Make sure you use the correct screw driver tip to remove these screws, which for the iPhone 6s Plus is the P2, otherwise you may strip the tip of the screw making it 10 times harder to remove. If once the screw is lose, it will not come off, use a magnet to remove it.

    Miguel Perez - Contestar

    If I do it by myself, will it damage the water resistant strip?

    I know iphone 7 have it ,but I am not sure 6s plus have it.

    Ganqian Zhu - Contestar

    iPhone 6s has an adhesive gasket under the display, similar to the iPhone 7—however, it doesn’t add much in the way of waterproofing since the 6s has non-sealed openings in other parts of the phone. Water resistance on the 6s is primarily internal (seals around the logic board connectors, etc.). It may still be worthwhile to replace the adhesive on the 6s in order to help keep the display firmly seated so it doesn’t move/wobble at all under pressure, but the phone will continue to work fine whether you replace the adhesive or not.

    Jeff Suovanen -

    Salve nella procedura iniziale di smontaggio display con la ventosa non è menzionato il fatto di scaldare i lati del display per “ammorbidire” la striscia che incolla il display alla scocca.

    Non è necessaria la cosa o è consigliabile ?

    grazie

    Hello, in the initial disassembling procedure with the suction cup, it is not mentioned how to heat the sides of the display to "soften" the strip that glues the display to the body.

    Is not the thing necessary or is it advisable?

    thank you

    Daniele - Contestar

    You’ve probably received your answer by now but for future enquirers, it does help the process of taking the screen off if heat is applied to the screen. If you have a hair Dryer use that on a low setting to heat the edges of the screen until it’s almost too hot to touch then slip very thin metal spudger around the edge to cut the adhesive. The carefully lift the screen with the help of the spudger and continue with your repair

    Cheers Wayne

    Wayne Lyell -

    How do I know that the Battery has ZERO Charging Cycles on it when it arrives ? Is there a (downside) to Higher Capacity batteries ? It is INCREDIBLY DIFFICULT to maintain a “Zero Chinese Products Lifestyle”, so how do I know that I’m not getting a deficient Chinese battery, potentially a refurb. battery ?

    integritybuilders - Contestar

    When your repair is complete, you can use coconutBattery to check your new battery stats and cycle count. (A properly tested battery may already have a charge cycle or two on it.) Avoid higher capacity batteries on iPhones—they’re generally either gimmicks, unsafe, or both. As far as the quality of the part, that comes down to how much you trust your supplier and whether they guarantee the product.

    Jeff Suovanen -

    So I need to empty the battery to zero percent?

    johnpatrickanat - Contestar

    Below 25%, exactly as stated in the instructions. There’s no benefit to draining it further than that, and in fact you’ll slightly shorten the service life of the battery by draining it all the way to zero. Follow the instructions exactly as written—if you go off-script, you’re a lot more likely to break something.

    Jeff Suovanen -

    So my screen shattered completely and the screen first had colored lines on tge while right side then it went out completely. If i get an lcd and digitizer replacement I'd that oing to fix it

    shellietheleo - Contestar

  2. Al abrir la pantalla en el 6s Plus, se separa una delgada tira de adhesivo alrededor del perímetro de la pantalla. Si prefieres reemplazar el adhesivo, ten listo un conjunto de nuevas tiras adhesivas antes de continuar. Es posible completar la reparación sin reemplazar el adhesivo, y probablemente no notarás ninguna diferencia en la funcionalidad.
    • Al abrir la pantalla en el 6s Plus, se separa una delgada tira de adhesivo alrededor del perímetro de la pantalla. Si prefieres reemplazar el adhesivo, ten listo un conjunto de nuevas tiras adhesivas antes de continuar. Es posible completar la reparación sin reemplazar el adhesivo, y probablemente no notarás ninguna diferencia en la funcionalidad.

    • Aplica una ventosa en la esquina izquierda inferior del ensamblaje de pantalla.

    take out screws first!!

    Yoav Karmon - Contestar

    Make sure you use the right screw driver tip for i phone 6s Plus, which is the P-2. If the screw will not come off once is lose, try using a magnet.

    Miguel Perez - Contestar

    My cracked screen prevented the suction cup from sealing. SOLUTION: With a piece of clear packing tape across the screen, the suction cup will seal and pull.

    Jim Cowles - Contestar

  3. Tira de la ventosa con una presión firme y constante para crear un ligero espacio entre el panel frontal y la caja posterior. Tirar demasiado fuerte puede dañar el ensamblaje de la pantalla. Aplica la presión necesaria para crear un pequeño espacio entre el ensamblaje de la pantalla y la caja posterior.
    • Tira de la ventosa con una presión firme y constante para crear un ligero espacio entre el panel frontal y la caja posterior.

    • Tirar demasiado fuerte puede dañar el ensamblaje de la pantalla. Aplica la presión necesaria para crear un pequeño espacio entre el ensamblaje de la pantalla y la caja posterior.

    I had a shattered front glass panel so I could not get the suction cup to seal properly. I tried a couple of different ways to get good suction but to no avail. I eventually used a Stanley knife to pry up the corner so I could get the spudger into the opening.

    John Architzel - Contestar

    A really high quality packing tape over the entire screen will usually be enough to use the suction cup on a shattered screen.

    djwooten -

    I used a suction cup on each side to provide counter traction. I braced the iphone between my knees and pulled apart while my helper inserted the spudger

    jkanne - Contestar

    This was by FAR the most difficult part of this whole thing. I confess the spudger was not cutting it so I used a butter knife to get into the small opening first, then used the spudger to go around the screen.

    Julie Sanchez - Contestar

    Hey everyone, if you never have done this part before be aware there is an extremely strong adhesive around the lip of the screen and once again is extremely strong. I had to get a friend to insert the pry/pick into the small gap while I used one hand to brace the phone down and the other to pull the suction cup without it digging into my hand. Go slow, it took me 5 tries because I didn’t realize how strong the adhesive was.

    bartmistrot - Contestar

    I also had a badly cracked lower screen - that glass was actually threatening to pull off the phone in chunks during this step, even with packing tape. Resorted to @j2arch’s tip and inserted a utility knife vertically into the seam between the display and phone body. Was able to lever the glass enough to get the spudger in there.

    Jason Augustyn - Contestar

    I have replaced sevrel screens for my sister in law and my niece. The packing tape has worked every time and that’s with it Shattered and pieces already falling out. You have to make sure the packing tape goes to the edge of the screen but doesn’t touch the frame. I have the plier like screen remover and use that it is much easier to remove the screen by your self with that tool. I also have the little finger suction cup that comes with the kit here. I bought the plier suction cup tool When I had to replace the screen that had the pieces of the screen missing and I don’t regret spending the extra money for that it has made a world of difference. I do this as a hobby it’s not a job for me. The electric divide repair kit from Lowe’s is also a very good kit to help. If you’re only going to do it once the kit that comes with the package is a great deal from ifixit. Well worth the money to spend the little extra to get the kit if you all ready don’t have the tools.

    Brent - Contestar

    If you try to use the spunger near the home button and try to pry it can crack your screen. This happened to me.

    Jeffrey - Contestar

    I found it easiest to use two suction cups. One on the front as directed, and a second one on the back. Give the spudger to your assistant, and have them slip it in place while you pull the display from the case.

    gordojenkins - Contestar

  4. El lugar más seguro para hacer palanca es la muesca en el panel frontal sobre la toma de auriculares. Mientras mantienes la presión sobre la ventosa, inserta la punta plana de un spudger en el hueco, directamente sobre la toma para auriculares. Mientras mantienes la presión sobre la ventosa, inserta la punta plana de un spudger en el hueco, directamente sobre la toma para auriculares.
    • El lugar más seguro para hacer palanca es la muesca en el panel frontal sobre la toma de auriculares.

    • Mientras mantienes la presión sobre la ventosa, inserta la punta plana de un spudger en el hueco, directamente sobre la toma para auriculares.

    This was by far the hardest part of the repair for me. Getting leverage while finding a way to prod with a spudger is a challenge in coordination. I used a second spudger with point holding the phone down by the headphone jack, with the other end of the spudger anchored to my desk.

    drpotter - Contestar

  5. Gire el spudger para ampliar el espacio entre el panel frontal y la caja trasera. Gire el spudger para ampliar el espacio entre el panel frontal y la caja trasera.
    • Gire el spudger para ampliar el espacio entre el panel frontal y la caja trasera.

    just changed the screen, but due to the tape along side the screen , it is best to heat a little so the glue losses and you can get the screen off better, like indicated

    Bart Blanckaert - Contestar

  6. Mientras tiras firmemente de la ventosa, desliza el borde del spudger debajo de la esquina inferior izquierda de la pantalla. Mientras tiras firmemente de la ventosa, desliza el borde del spudger debajo de la esquina inferior izquierda de la pantalla. Mientras tiras firmemente de la ventosa, desliza el borde del spudger debajo de la esquina inferior izquierda de la pantalla.
    • Mientras tiras firmemente de la ventosa, desliza el borde del spudger debajo de la esquina inferior izquierda de la pantalla.

  7. Desliza la punta del spudger por el lado izquierdo del teléfono, entre el panel frontal y la caja posterior. Desliza la punta del spudger por el lado izquierdo del teléfono, entre el panel frontal y la caja posterior.
    • Desliza la punta del spudger por el lado izquierdo del teléfono, entre el panel frontal y la caja posterior.

  8. Inserta la punta plana del spudger debajo del borde derecho de la pantalla. Desliza el spudger por el lado derecho.
    • Inserta la punta plana del spudger debajo del borde derecho de la pantalla.

    • Desliza el spudger por el lado derecho.

  9. Usa una herramienta de apertura de plástico para mantener presionada la caja trasera mientras levantas la ventosa para abrir el teléfono. No retires la pantalla por completo o dañarás los cables de datos que la conectan cerca del borde superior del iPhone.
    • Usa una herramienta de apertura de plástico para mantener presionada la caja trasera mientras levantas la ventosa para abrir el teléfono.

    • No retires la pantalla por completo o dañarás los cables de datos que la conectan cerca del borde superior del iPhone.

  10. Baterías para portátiles

    Baterías para las marcas de PC más top, respaldadas por nuestra Garantía de Calidad.

    Comprar Ahora

    Baterías para portátiles

    Baterías para las marcas de PC más top, respaldadas por nuestra Garantía de Calidad.

    Comprar Ahora
  11. Tira de la pequeña protuberancia de la ventosa para extraerla de la pantalla. Tira de la pequeña protuberancia de la ventosa para extraerla de la pantalla.
    • Tira de la pequeña protuberancia de la ventosa para extraerla de la pantalla.

    Remember to apply the screen gasket on the re-assemble. The gasket is provided in the kit but not mentioned here on the instructions.

    Won Hong - Contestar

    There’s a link to the entire gasket replacement procedure in Step 21.

    Jeff Suovanen -

  12. Sujeta suavemente el ensamblaje de la pantalla y levántalo para abrir el teléfono, utilizando los clips en la parte superior del panel frontal como bisagra. Abre la pantalla aproximadamente a un ángulo de 90º, e inclínala contra algo para mantenerla apoyada mientras estás trabajando en el teléfono. No abras la pantalla más de 90º; aún está conectada a la parte superior del teléfono por medio de la pantalla, el digitalizador y los cables de la cámara frontal, que pueden romperse fácilmente.
    • Sujeta suavemente el ensamblaje de la pantalla y levántalo para abrir el teléfono, utilizando los clips en la parte superior del panel frontal como bisagra.

    • Abre la pantalla aproximadamente a un ángulo de 90º, e inclínala contra algo para mantenerla apoyada mientras estás trabajando en el teléfono.

    • No abras la pantalla más de 90º; aún está conectada a la parte superior del teléfono por medio de la pantalla, el digitalizador y los cables de la cámara frontal, que pueden romperse fácilmente.

    • Agrega una banda elástica para mantener la pantalla en su lugar mientras trabajas. Esto evita una tensión excesiva en los cables de la pantalla.

    • En caso de necesidad, puedes utilizar una bebida enlatada sin abrir para apoyar la pantalla.

    • Remueve los dos tornillos Phillips que sujetan el soporte de conector de batería a la placa lógica:

    • Un tornillo de 2.9 mm

    • Un tornillo de 2.3 mm

    • A lo largo de esta guía, mantén un registro cuidadoso de tus tornillos para que cada uno vuelva a su lugar durante el re-ensamblaje Instalar un tornillo en el lugar equivocado puede causar daños permanentes.

    FYI - I used some blue painters tape wrapped around a piece of cardboard to hold the screws and brackets in place, in order, so they did not get lost. Some of those screws are MICROSCOPIC so be careful!

    I also suggest having very good lighting, even a camping headlight for hands-free well lit work space. You will thank me later :-)

    Julie Sanchez - Contestar

    Use the bit labeled “PH000”.

    Joe Teichert - Contestar

    PH000 bit just wants to free-spin in the 2.3 mm screw. no bite in the head at all. had no difficulty removing the 2.9 mm screw with the same Phillips. had to abandon battery replacement effort.

    Benjamin Stalcup - Contestar

    For this part, neither PH000 or Y000 worked. Technically, it’ll set you back 31$ because you will need the PH00 screwdriver for this part, and the part where you need to open the screen. They have ph00 screwdrivers in every hardware store and even ifixit.com. just know that they put the wrong screwheads for you

    Jack Daniel - Contestar

    Do not lose track of which hole these screws go into. They MUST be put back into the correct hole that they came out of. If not, you will get the dreaded “long screw damage” on the mainboard, and that will be the end of the show.

    Just remember where these screws go, and it will be fine.

    Harry McDow - Contestar

    This step is extremely important in fixing your phone: I had an iPhone that I fried as I forgot to disconnect the battery, end of the show!

    Jaron Foo - Contestar

  13. Remueve el soporte de conector de batería. Remueve el soporte de conector de batería.
    • Remueve el soporte de conector de batería.

    Does it matter if the brackets arent put back in the phone? I bought a used phone and brackets are missing. Thanks!

    Coupon Crazy - Contestar

  14. Usa un spudger o una uña limpia para desconectar el conector de la batería haciendo palanca hacia arriba de la placa lógica. Usa un spudger o una uña limpia para desconectar el conector de la batería haciendo palanca hacia arriba de la placa lógica. Usa un spudger o una uña limpia para desconectar el conector de la batería haciendo palanca hacia arriba de la placa lógica.
    • Usa un spudger o una uña limpia para desconectar el conector de la batería haciendo palanca hacia arriba de la placa lógica.

  15. Dobla el conector hacia atrás para asegurarte de que no haga contacto y encienda el iPhone mientras trabajas en él. Dobla el conector hacia atrás para asegurarte de que no haga contacto y encienda el iPhone mientras trabajas en él. Dobla el conector hacia atrás para asegurarte de que no haga contacto y encienda el iPhone mientras trabajas en él.
    • Dobla el conector hacia atrás para asegurarte de que no haga contacto y encienda el iPhone mientras trabajas en él.

    When putting the new battery in, make sure to line up the plug and not to the top of the battery… our battery was smaller so the plug would NOT have lined up if we used the top of the battery. ALSO, the plug was NOT 90 degrees so we had to finagle the plug. Also, make sure there is a clear CLICK when you plug in the connector or it may not work. Ours went in but guess didn’t go far enough so we had to take the screen off and push it harder until we heard the “click” then it worked fine.

    Won Hong - Contestar

  16. Remueve los siguientes tornillos Phillips :
    • Remueve los siguientes tornillos Phillips :

    • Tres tornillos de 1.3 mm

    • Un tornillo de 1.6 mm

    • Un tornillo de 3.0 mm

    • Durante el reensamblaje, es fundamental colocar este tornillo de 3.0 mm en la esquina superior derecha del soporte. Colocarlo en otro lugar puede dañar la placa lógica.

    I really don't see value in removing screen use box and rubber band keep at 90 degrees.

    John Parker - Contestar

    I leave screen on as well for this. - Tho I prefer a 45 degree lean.

    Thor -

    I just changed my battery and also left the screen attached. I was lucky enough to get all 3 adhesive battery strips out clean so I didn’t have a struggle with the battery coming out. If I was going to need to get rough with it I was going to take the screen off at that point.

    Michael Gross - Contestar

    To keep track of screws, draw a quick outline of the display cable bracket/cover, with five dots where screws should be. Drop the screws on the corresponding dot. Helps if you use magnet pad.

    Christa - Contestar

    Better yet, print out the pictures from the iFixit website, and use clear tape (“Scotch tape”) to TAPE the screws onto the place in the picture where they belong.

    Tom -

    Which screwdriver from the kit do I use for which screw?

    Shiva Sharma - Contestar

    I made a mistake and unscrewed the screw just north north west of the one circled in yellow. Of course I lost the screw. Can anyone give me any guidance about this? what does the wire connected to it do? What is the size of the screw, in case I have to replace it?

    P.S. This is another reason to consider the possibility of NOT removing the screen just to replace the battery: removing the screen presents a additional possible headache, especially for people like me with bad eyesight who probably shouldn’t be doing this in the first place.

    Tom - Contestar

  17. Remueve el soporte del cable de pantalla. Remueve el soporte del cable de pantalla.
    • Remueve el soporte del cable de pantalla.

  18. Ten cuidado de solo levantar el conector y no el zócalo de la placa lógica. Usa una herramienta de apertura de plástico para desconectar la cámara frontal y el conector del cable del sensor.
    • Ten cuidado de solo levantar el conector y no el zócalo de la placa lógica.

    • Usa una herramienta de apertura de plástico para desconectar la cámara frontal y el conector del cable del sensor.

    FYI, in the video she uses the spudger for this but I think either one will work.

    Julie Sanchez - Contestar

  19. Usa una herramienta de apertura de plástico para desconectar el cable del digitalizador y  sacarlo de su zócalo en la placa lógica Cuando vuelvas a conectar el cable del digitalizador, no presiones el centro del conector. Presiona un extremo del conector, luego presiona el extremo opuesto. Presionar en el centro del conector puede doblar el componente y causar daños al digitalizador.
    • Usa una herramienta de apertura de plástico para desconectar el cable del digitalizador y sacarlo de su zócalo en la placa lógica

    • Cuando vuelvas a conectar el cable del digitalizador, no presiones el centro del conector. Presiona un extremo del conector, luego presiona el extremo opuesto. Presionar en el centro del conector puede doblar el componente y causar daños al digitalizador.

    Thanks you i fix it

    God Hand - Contestar

    “When reconnecting the digitizer cable, do not press the center of the connector. Press one end of the connector, then press the opposite end. Pressing in the center of the connector can bend the component and cause digitizer damage. “

    The following note above was so helpful. I was speeding through the process of getting things back together, since it seemed easy to connect the digitizer cable, but I kept pushing it in the middle and I wouldn’t connect. Until I read through this step and realized it was easier if I would’ve connected one side and then the opposite side right after.

    Jeffrey Robinos - Contestar

    Don’t be too shy when pushing the ends of the digitizer connector back to place. If it does not connect properly, you might face the “half backlight” problem, even if you did not kill any LCD filter. Also check carefully, that you don’t clamp parts of the sticky sealing material placed around the connector inside the connection area.

    Norbert Andreas Richartz - Contestar

  20. Asegúrate de que la batería está desconectada antes de desconectar o reconectar el cable en este paso. Desconectar el cable de pantalla levantándolo de su zócalo en la placa lógica.
    • Asegúrate de que la batería está desconectada antes de desconectar o reconectar el cable en este paso.

    • Desconectar el cable de pantalla levantándolo de su zócalo en la placa lógica.

    How much is this to replace?

    Alistair knight - Contestar

    And where could I buy from?

    Alistair knight - Contestar

    After finishing the assembly I got the message “Touch ID cannot be enabled on this phone”. I found this connector was loose. Plugged it back in and that fixed it.

    Bryan Province - Contestar

    Always make sure to disconnect the battery before you do any work on the phone replacing any parts the digitizer or anything. And before you start make sure the phone is turned off you don’t want any power surges. If you also have a static electricity bracelet that also is a plus to use but isn’t a necessity just a nice piece of mind. Some cases you do need to use one so you don’t discharge static electricity to an electrical component and mess it up.

    Brent - Contestar

    Be very careful in this step. I noticed it’s very easy to tear the flex when trying to lift it out of its socket from the right side.

    shoeib - Contestar

    What is the cable and how is it connected/fixed to the motherboard between the bottom socket and the screw hole.

    Mine came loose somehow?

    Jason Engelsman - Contestar

    I figured out my own question its the Wi-Fi diversity antenna cable. But how is it connected/secured to the motherboard?

    Jason Engelsman - Contestar

    i pressed on the center of the digitizer connection. and the bottom half of my screen didnt work. i then took that same front panel assembly and tried to install it on another old iphone 6s+ and i had the same issue.

    can i still fix it?

    what exactly is broken now?

    alejandro rueda - Contestar

    @mynameisoli Honestly this just sounds like a defective screen to me, but it’s hard to say for sure. Look closely at the connector at the end of the ribbon cable and check it for damage. If it’s slightly bent/curved, all the pins won’t make good contact in the socket. You can try bending it back so it lays flat, but you have to be very careful not to damage the connector or contaminate the pins with skin oils, so it’s tricky—and it may be harder to return as “defective” if you mess up the connector. So try this at your own risk. Apart from that, I would just return it and try a different display. Good luck!

    Jeff Suovanen -

  21. Remueva el ensamblaje de pantalla. Durante el reensamblaje, deténte aquí si deseas para reemplazar el adhesivo  alrededor de los bordes de pantalla.

    For instructions on home button swap out to the new screen you just installed, go here

    Reemplazo del ensamblaje del botón de inicio del iPhone 6s Plus

    Superior Office Systems - Contestar

    Do you know whether the adhesive contributes to waterproofing, or just for stability/adhesion?

    Christa - Contestar

    @kitabel The iPhone 6s case isn’t waterproof, so I don’t think adhesive around the display is contributing anything other than stability. The 6s series does have some water resistance, but it’s mostly internal and not something Apple advertises.

    Jeff Suovanen -

    If you have a replacement adhesive for the display, you may need to install it before reconnecting cables to the components. If the adhesive wraps all the way around the display, it will be impossible to install it once the display is reconnected.

    Matthew Olwell - Contestar

    These instructions worked great for me. Thank you!

    Chris Enloe - Contestar

  22. Despega cualquier cinta que cubra los tornillos del soporte de la cámara iSight Despega cualquier cinta que cubra los tornillos del soporte de la cámara iSight Despega cualquier cinta que cubra los tornillos del soporte de la cámara iSight
    • Despega cualquier cinta que cubra los tornillos del soporte de la cámara iSight

    If like me you are only wanting to clean out the speaker, you do not need to do this step. You can skip to step 50

    Brad “Bradster48” Mason - Contestar

  23. Remueve los siguientes tornillos Phillips del soporte de cámara:
    • Remueve los siguientes tornillos Phillips del soporte de cámara:

    • Un tornillo de 1.9 mm

    • Un tornillo de 2.4 mm

  24. Remueve el soporte de la cámara iSight. Remueve el soporte de la cámara iSight.
    • Remueve el soporte de la cámara iSight.

  25. Desconecta el conector de cámara iSight de su zócalo en la placa lógica. Asegúrate de levantar solo el conector y no el zócalo en la placa lógica.
    • Desconecta el conector de cámara iSight de su zócalo en la placa lógica.

    • Asegúrate de levantar solo el conector y no el zócalo en la placa lógica.

    If necessary, the sticky patch on top f the connector should be removed. Helped my case a lot :)

    Alexander Leuschner - Contestar

  26. Inserta el extremo plano del spudger entre la cámara iSight y la caja trasera. Con cuidado levanta la cámara de su zócalo.
    • Inserta el extremo plano del spudger entre la cámara iSight y la caja trasera.

    • Con cuidado levanta la cámara de su zócalo.

  27. Remueve la cámara iSight. Remueve la cámara iSight.
    • Remueve la cámara iSight.

    Hi ,

    Thanks a lot for your tutorial !

    Can you explain how can we change the lens of the camera ?

    Thanks ;)

    rocofolie - Contestar

Conclusión

Para volver a ensamblar tu dispositivo, sigue estas instrucciones en orden inverso.

77 personas más completaron esta guía.

Un agradecimiento especial a estos traductores:

100%

¡ Mariana nos está ayudando a reparar el mundo! ¿Quieres contribuir?
Empezar a traducir ›

Evan Noronha

Miembro Desde 05/02/15

171,407 Reputación

177 Guías creadas

Equipo

iFixit Miembro de iFixit

Community

99 Miembros

9,253 Guías creadas

really useful.

vickyhhchang - Contestar

Great instructional video which saw me through the entire disassembly of my phone, and then clear and concise enough steps on the page to help me put it back together after installing the new camera. Thank you!!!!

chyke_dawg - Contestar

I completed this repair at the same time as replacing my battery and headphone/lightening jack assembly. The problem I was experiencing with my camera was jittery video and unusable photos. The stabilization gimbal had died, though I am not sure that is the right word for it. It's more like it had an overdose. Anytime I would come to use the camera you could hear a tiny clicking noise as the lens armature shot itself about within its tolerances. Photos were out of focus and jittery, even when taken with the phone completely stable and untouched. I could most of the time just manage to make it take photos to deposit checks by holding the phone horizontally and in very bright sunlight, sometimes tapping the phone until the clicking noise stopped. Videos would hunt for focus and look as though I was actively shaking the camera, no matter what. Sometimes it was worse than others. Replacing this assembly completely fixed all issues.

Michael Cornforth - Contestar

Michael, you might have been interested to know that the focusing problems you experienced are chronic in the iPhone 6 Plus and Apple has created a repair program. You might have found this page useful if your serial number was eligible. https://www.apple.com/support/iphone6plu...

Talon - Contestar

Micheal, I am having that same problem as well! Good to know that replacing it fixes it!

Talon, the repair program Apple has is only for the 6 plus not the 6s plus.

Andy Perkins - Contestar

By the camera lens is a tiny strap piece that I bumped off and now I am not sure how to put it back on?? Do you have any pictures or advice that would show me how it goes back in the phone?

Patricia Brown - Contestar

Hi, I was wondering if it was possible since my camera on iphone 6 plus is damaged, if I can replace it with a 6s since it's 12 megapixels. Let me know your though.

Omar Jimenez - Contestar

i got this and accidentally got a regular 6 plus not the 6s plus camera . apparently there is a difference because it wouldn't work. Replaced it and works great. anyone with a brain and a steady hand can do this.

nathan Reich - Contestar

so I installed a new camera and after re-installing the front of the phone…the screen is unresponsive to typing in the passcode or accepting a fingerprint to open the phone back up.  everything works fine..i’m even seeing txt messages come in…just cant seem to unlock the phone because the  keypad isn't responsive.  any advice?

jeremy riggs - Contestar

I replaced my rear camera and now neither camera has an image! What did I do wrong?

Bill Anderson - Contestar

I had very bad issues with the i-Sight cam! it was shaking so wild, you couldnt see anything on the pictures. Apple said, my 6S+ is not under this special i-Sight change programm which was describing precisely the same issues!

But the new cam fixed it all! And put a new battery as well ;-)

elcojone - Contestar

I just discovered that the iSight camera does not include the camera cover. I also cannot find the camera cover for sale on this site. This is very frustrating. I didn’t know the camera and cover were separate pieces. I think I just bought the camera when I didn’t need it and didn’t buy the cover that I do need.

This is not good. Please help!

Darren Sullivan - Contestar

Couldn’t have done it without the step by step guidance and video. Thanks for the help. New camera works great!!!

jeff jamison - Contestar

Dropped my iPhone and the camera succumbed to the “Black Death”. No software fix for this one. Bought a great toolkit from iFixit along with a new iSight camera. Following these well documented instructions had the phone fixed in short order. What a great website!

Bryan Thomas - Contestar

camera wont focus

Xavier - Contestar

Really fun to do and the breakdown was helpful and easy to follow, thank you

Marcos De Loera - Contestar

Is the iphone 6S plus camera the same as the iphone 6.

Marco Marchant - Contestar

No, they are different and non-compatible.

Talon - Contestar

Newbie question. If I replace camera as in the instructions, will I need to reloadd all apps and data ?

Peter - Contestar

No this dosent effect the data on your phone only the camera which you are changing

thomaschatstg -

Help!

ipone 6s +.

Had blurry rear camera. Ordered new camera. I Just replaced camera this morning & now when I powered. Ack on…black screen for rear & FRONT camera as well now!

I rebooted phone.

i checked settings.

i reset setttings.

I even took apart again to double check my connections.

Any ideas?

myred - Contestar

Agregar Comentario

Ver Estadísticas:

Ultimas 24 Horas: 151

Últimos 7 Días: 345

Últimos 30 Días: 1,455

Todo El Tiempo: 65,237