Saltar al contenido principal

Reemplazo de batería en Microsoft Surface Pro

Qué necesitas

  1. Reemplazo de batería en Microsoft Surface Pro, Batería: paso 1, imagen 1 de 2 Reemplazo de batería en Microsoft Surface Pro, Batería: paso 1, imagen 2 de 2
    • Usando un destornillador Torx T3, quita los 23 tornillos del bisel del Surface Pro.

    My Surface Pro 1 needs a T4 screwdriver for these screws.

    Sheryl - Contestar

    Mine used T3s.

    Dan - Contestar

  2. Reemplazo de batería en Microsoft Surface Pro: paso 2, imagen 1 de 1
    • Levanta el bisel de la pantalla del Surface Pro

  3. Reemplazo de batería en Microsoft Surface Pro: paso 3, imagen 1 de 2 Reemplazo de batería en Microsoft Surface Pro: paso 3, imagen 2 de 2
    • Quita los 6 tornillos T5 de los paneles a cada lado del cuadro

    • Quita los 23 tornillos T2 de los paneles.

    On my Surface Pro 1, the screws labeled as T5 are T3.

    Sheryl - Contestar

  4. Reemplazo de batería en Microsoft Surface Pro: paso 4, imagen 1 de 1
    • Levanta los dos paneles de metal del cuadro

  5. Reemplazo de batería en Microsoft Surface Pro: paso 5, imagen 1 de 2 Reemplazo de batería en Microsoft Surface Pro: paso 5, imagen 2 de 2
    • Usando unas pinzas, tira con delicadeza de los ocho cables de cinta para sacarlos de sus encajes.

    There’s an additional black ribbon cable (top center in picture) that needs to be unplugged. Also, open the release for the cables before trying to pull them out.

    Sheryl - Contestar

  6. Reemplazo de batería en Microsoft Surface Pro: paso 6, imagen 1 de 2 Reemplazo de batería en Microsoft Surface Pro: paso 6, imagen 2 de 2
    • Desatornilla los 17 tornillos Torx T5 de la placa base con el destornillador Torx T5

    There’s an 18th screw that needs to be removed. It’s in the upper right corner of the picture, but not circled.

    Sheryl - Contestar

    The 6 screws holding the fans in place should not be removed (3 on each side - heads look different). They just attach the fans to the motherboard.

    Sheryl - Contestar

    One of these screws is thinner than the others, which I didn’t notice until I started screwing them back in.

    Sheryl - Contestar

  7. Reemplazo de batería en Microsoft Surface Pro: paso 7, imagen 1 de 1
    • Una vez hayas quitado todos los tornillos, levanta con cuidado la placa lógica con tus manos para sacarla.

  8. Reemplazo de batería en Microsoft Surface Pro: paso 8, imagen 1 de 2 Reemplazo de batería en Microsoft Surface Pro: paso 8, imagen 2 de 2
    • Usa tus manos para sacar las baterías con la fuerza suficiente como para separarlas del pegamento que las mantenía en su posición.

    This is possible to do. The worst part are all the tiny screws and glue to get the cover and touch screen off. I bought the battery for $45 off of Ebay and a set of four Torx screw drivers for $5.

    Tips:

    check the 12V coming into the main board after the cover is off. You will see a red boot light on the main board flash for a sec. You should hear the tiny fans going.

    Use an external monitor and cables to check the per and boot before putting it all back together.

    Sal V - Contestar

    I wonder how many could serviced in one day 4 ? We just been asked to service on a regular basis, finding some information on this thanks for the service breakdown..

    Pete - Contestar

    I am looking to get mine repaired and I am terrified to do it myself. Do y’all know somewhere I can send it.

    Payton Mitchell - Contestar

Conclusión

Para montar de nuevo el dispositivo, sigue las instrucciones en orden inverso

35 personas más completaron esta guía.

Un agradecimiento especial a estos traductores:

en es

100%

Estos traductores nos están ayudando a reparar el mundo! ¿Quieres contribuir?
Empezar a traducir ›

Jonathan Choi

Miembro Desde 10/09/13

1,005 Reputación

4 Guías creadas

Equipo

Cal Poly, Team 8-20, Regan Fall 2013 Miembro de Cal Poly, Team 8-20, Regan Fall 2013

CPSU-REGAN-F13S8G20

4 Miembros

16 Guías creadas

24 comentarios

Thank you for that awesome guide!

Do you know where can i buy a battery for surface pro 2??

Thanks

John john - Contestar

I am also trying to find out where to acquire the Surface Pro batteries...???

Tristan Irons -

im also looking for a surface pro replacement battery.

Lekan Adesanya - Contestar

I just bought one for $70 at a site called newpower99.com... should be here in 2 days. I have no idea if it will work, but it says it comes with a toolkit to replace it. I hope it works.

Matt -

Did you have success installing the Newegg battery?

asmac - Contestar

sorry, make that newpower99

asmac - Contestar

I guess we can assume the people who tired using the aftermarket batteries were killed in the process of repairing their Surface Pro. May their valiant efforts be remembered for all the days.

pocketdrummer - Contestar

I completed this repair.

Notes:

The battery from newpower99 is the correct battery. It does not, however, come with the correct screwdrivers to complete the repair. (I believe they sent a T3, T4, and T5 torx when the repair requires a T2, T3, and T5).

The screen removal is the most difficult part of the repair. In addition to the cables on the bottom of the unit as other repairs have mentioned, the screen assembly itself is very vulnerable to being punctured. In places on the screen assembly, there is only a thin layer of tape sealing the gap between what looks like the LCD/Digitizer and the glass panel.

When you are prying the screen off, be very careful about how deep you go, as puncturing the seal can brick your screen (my screen fell victim to it).

To that end, pay very close attention to the bezel width. It is a different width on every edge. The left side is approximately the same width as the bezel on the glass, the right side is a mm or two skinnier, top is skinnier still and the bot is small.

Scalar - Contestar

Continued:

Once the screen assembly is off, the repair is not bad. My unit is a surface Pro 2, so there were a few different screw placements, but it's almost the same.

The screws are incredibly obnoxious. Not only do they require three different screwdrivers, there are many multiple widths and lengths within a screw type. Screw organization is a must.

The adhesive is a big problem as well. The tape holding together my battery assembly looks like it bled some adhesive, which cause my logic board to stick to the battery. A precarious few minutes later, I was able to put enough pressure to pull the board without flexing it too much. The battery is basically welded to the back panel with tape and adhesive. It took all my strength to tear it off the back panel.

If you are reading this and looking to complete this repair, do yourself a favor and order a replacement screen assembly ahead of time. They are approximately $60 now, and there is a good chance of the screen not surviving disassembly.

Scalar -

The Microsoft part number for the OEM Surface Pro 1 Model 1514 battery is P21GU9. The Surface Pro 2 Model 1601 uses the same battery. If you search on eBay for “battery P21GU9”, you’ll find a lot of them - all from Chinese sellers. I just bought one that’s theoretically OEM and brand new (unused) for $35. The seller has a high rating, so hopefully it’s true.

Sheryl - Contestar

how do i glue the new battery back in place?

Franz Hofmann - Contestar

You glue it back in with double-sided tape. You can get it on Amazon, but most batteries meant to be glued in come with the tape already on it. When my new battery gets here, I’m not going to glue it in as completely as it was. Seems like overkill, and it’s too hard to remove.

Sheryl - Contestar

I just removed the battery from my Surface Pro 1. I don’t have the new battery yet. If I try to plug it in with no battery, will I destroy it?

Sheryl - Contestar

Well, I had to try it. I plugged it in and turned it on (with no battery) and it worked! So I’m going to screw everything down and just run it this way. I don’t really need the battery (though I ordered it).

Sheryl - Contestar

Any chance anyone who’s done this replacement is still following this page? My Surface Pro 2 battery has started to majorly crap out, so I think I’m going to grab a battery here and give this a try. I have definitely not been happy with the build quality of my Surface, in fact, the adhesive at the bottom and 90% of each side has failed more than 6 months ago, so I’m thinking it should be much easier for me to remove the screen. I’ll mainly just need to deal with the top edge of the device.

My question is how to re-”glue” the screen once you take it off? Is that possible? I saw someone mention double sided tape to use to attach the new battery, but would you use the same thing for the screen? Hoping someone can help offer insight from experience. Thanks!

Robert Higgs - Contestar

@rchmx To reinstall the screen, remove all the old adhesive and clean the mating surface with >90% isopropyl alcohol, and then secure it with a strong/thin double-sided tape, such as Tesa 61395. This repair is not for the faint of heart. Good luck!

Jeff Suovanen -

@jeffsu Thanks Jeff! Yes, I had found that after doing a bit more searching. The battery in my SP2 is now completely non-functional, but luckily a while back it had bloated to the point where 70+% of the screen has been detached for the casing, so hopefully that will make the process a bit easier. And anyways, it’s necessary to return the device to a more than basically functional level, so I have no choice but to dig in after the holidays are over.

Robert Higgs -

you might be able to find one on Newegg

George Sherman - Contestar

What type of glue do you use to re-seal the system?

Tyler Hardy - Contestar

? Wish me luck ! I’m going to try it. Thank You All, for your contributions . Microsoft valued my Surface at $7.50

exchange. I’ve got nothing to loose.

Ted Nielsen - Contestar

warning: this is not the surface pro 5, because when MS anounced the pro 5 they anounced it as the Surface Pro. I learned it the hard way and now i need a new display, because the edge (where the glue ist) is thinner at the pro 5. In total, it will take you arround 40 screws for the pro 5 to change the battery. way less than here

Flavio Ried - Contestar

hellow me surface pro 4 battery dead and i want to change it . but iam from iran and microsoft doesnt any branch in country and i confused . but finally i find nozhino microsoft surface repair clinic in google and they change my surface battery with best performance thanks for nozhino

kimi - Contestar

Replaced the battery and although it charges the surface wont run off battery at all.

Farrell Segall - Contestar

Which battery did you buy?

iluecker -

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 48

Ultimos 7 días: 336

Ultimos 30 días: 1,471

Todo El Tiempo: 229,475