Saltar al contenido principal

Introducción

El motor Táptico produce las funciones de vibración y el feedback háptico de tu iPhone. Usa esta guía para remover y/o reemplazar el Motor Táptico en tu iPhone 7.

Esta guía te enseña a remover el ensamblaje de pantalla para prevenir el daño a los cables de pantalla, Si te sientes cómodo removiendo el Motor Táptico sin poner excesiva presión en los cables de pantalla, puedes saltear los pasos para extraer la pantalla.

Resumen del Video

  1. Antes de comenzar, descarga la batería de tu iPhone por debajo del 25%. Una batería de iones de litio cargada puede incendiarse y / o explotar si se perfora accidentalmente.
    • Antes de comenzar, descarga la batería de tu iPhone por debajo del 25%. Una batería de iones de litio cargada puede incendiarse y / o explotar si se perfora accidentalmente.

    • Apaga tu iPhone antes de comenzar el desmontaje.

    • Remueve los dos tornillos pentalobe de 3.4 mm en el borde inferior del iPhone.

    • Abrir la pantalla del iPhone dañará sus sellos impermeables. Ten sellos de reemplazo listos antes de seguir con el próximo paso o ten cuidado de evitar la entrada de líquidos si vuelves a ensamblar tu iPhone sin reemplazar los sellos.

    Can anyone confirm 7/7P's pentalobe screws have a ring of seal near the screw head?

    Cooper Chase - Contestar

    Confirmed, the screws have a black ring seal around the head.

    rcheing - Contestar

  2. Calentar el borde inferior del iPhone ayudará a suavizar el adhesivo que asegura la pantalla, facilitando su apertura.
    • Calentar el borde inferior del iPhone ayudará a suavizar el adhesivo que asegura la pantalla, facilitando su apertura.

    • Utiliza una pistola de calor o preparar un iOpener y aplicarlo en el borde inferior del iPhone durante un minuto para suavizar el adhesivo debajo.

    ¿Cuántos segundos son los recomendados?

    joscarlos91 - Contestar

    Sesenta segundos

    Krutav Shah -

    It is a process. I heated the lower area of the phone with a hair dryer on and off (1min each) about 3-4 times before I was able to get the provided tool in.

    Dan - Contestar

    I suggest using a hairdryer. I used the iOpener for maybe 30 mins to no avail. However, when I used the hairdryer the screen came of much quicker.

    Michael - Contestar

    I totally Mr. Myagi’ed it, by rubbing my hands together until they burned, then held the phone un my hot hands. I did this 5-6 times over a couple of minutes. It was a good zen way to get started!

    Ark - Contestar

    Can a heat gun be used?

    Lee - Contestar

    Absolutely. Just don’t overdo it—the adhesive usually softens up pretty easily. If you are experienced with a heat gun, you’ll have no problem. (If you are inexperienced, it’s easy to cook the display or cause other damage.)

    Jeff Suovanen -

    If i use this process, will iphone 7 still be sealed, water/ splash resist after that?

    Marius Serban - Contestar

  3. Conecta una ventosa a la mitad inferior del conjunto de la pantalla, justo por encima del botón de inicio. Asegúrate de que la ventosa no se coloque sobre el botón de inicio, ya que esto evitará que se forme un sello entre la ventosa y el vidrio frontal.
    • Conecta una ventosa a la mitad inferior del conjunto de la pantalla, justo por encima del botón de inicio.

    • Asegúrate de que la ventosa no se coloque sobre el botón de inicio, ya que esto evitará que se forme un sello entre la ventosa y el vidrio frontal.

    The glass is completely cracked and the suction cup doesn't work because it gets air in between. any tip?

    Display is glued and doesn't come off.

    support - Contestar

    A wide, single strip of packing tape, well placed, will solve this for you. :)

    Mimic44444 - Contestar

    Last comment works well. Thank you !

    Using packing tape for a cracked screen should be included in the description in Step 3.

    Cracked screen is most probably the reason you are replacing it.

    Arni Benediktsson - Contestar

    I agree that using packing tape for a cracked screen should be included in this steps description. I don’t have wide but turned mine horizontal and that worked great.

    Mary Knapp - Contestar

    Bekomme die Oberschale einfach nicht runter! Trotz mehrmaligem erwärmen durch den iOpener und seitlichen bewegen! Weiß nicht mehr weiter!

    Stephan Lienhard - Contestar

  4. Tira hacia arriba de la ventosa para crear un pequeño espacio entre el ensamblaje de pantalla y la caja trasera. Inserta el extremo plano de un spudger en el hueco. El adhesivo  que sostiene la pantalla en su lugar es muy fuerte, y la creación de esta separación inicial requiere una cantidad significativa de fuerza. Si te resulta difícil crear una abertura, oscila la pantalla hacia arriba y abajo para debilitar el pegamento hasta que puedas insertar el  spudger.
    • Tira hacia arriba de la ventosa para crear un pequeño espacio entre el ensamblaje de pantalla y la caja trasera.

    • Inserta el extremo plano de un spudger en el hueco.

    • El adhesivo que sostiene la pantalla en su lugar es muy fuerte, y la creación de esta separación inicial requiere una cantidad significativa de fuerza. Si te resulta difícil crear una abertura, oscila la pantalla hacia arriba y abajo para debilitar el pegamento hasta que puedas insertar el spudger.

    This was SO hard for me to do with the spudger. I couldn’t get a gap to insert it because my phone was so cracked (even though I used tape on the front) to get a solid seal with the suction cup. I ended up taking a VERY thin knife and inserting it straight down to make the initial break that allowed me to insert the spudger.

    jessica harlow - Contestar

    I’ve given up using a plastic spudger to try to open any of these phones. I use a metal one with a flat base and a very sharp end…close to a razor. As long as I’m careful, it won’t slip and scratch the base. It’s much easier than using these plastic spudgers.

    mcr4u2 -

    Im trying to get the screen off right now and my phone is not cracked and its still a pain

    Jordon Johnson - Contestar

    Using a blow dryer was extremely helpful and using the suction cup towards one of the lower edges was also helpful

    Jordon Johnson - Contestar

    This is not working for me. How long does the heat need to be applied? Still trying right now…. =/

    Chris Gallego - Contestar

    Apply hair dryer for at least 1 minute. I inserted the tip end of a thin mini screwdriver and with some force, pryed it open and inserted my plastic spudger to continue the separation process. It worked, just be patient.

    Please wear protective glasses! My iPhone glass was severely cracked, when separating the glass a corner area of broken glass exploded in my face. Apply transparent tape over the broken glass to contain the shards.

    amberron - Contestar

    I second Jessica’s January 8 comment.  I just finished a battery replacement on my iPhone 7 and this step was the most nerve-wracking part.  I ended up using a sharper (but not razor-sharp) metal object to get this done with confidence (tried the spudger and guitar pick but not thin enough).  The tool I used was the exact duplicate of what iFixIt calls “iSesamo Opening Tool” in their tool selection.  I did the heat up with a hair dryer (after attempts with an iOpener hot pad) and the secret (as Jessica also noted)  was to not use the angle of attack shown in the pictures, but to push it in more vertically along the bottom edge while pulling up on the suction cup.  From there you can easily lever the tool to the lower angle-of-attack (as shown in the picture).  I actually used the metal tool for most of the perimeter as well, just don’t go deep (you don’t need to).  Notes: my display was intact, and I was able to pull up fairly hard with a glass screen protector still on it.

    Ted - Contestar

    This is frustrating. I heated the lower edge with a hair dryer for 1 min on high about 3-4 times. In between each heat cycle, I rocked the suction cup back and forth. I was eventually able to create significant space for the provided tool. This takes a lot of patience. Once the space was created, it was very easy to remove the screen.

    Dan - Contestar

    use a fingernail, then the blue tool, then the spudger

    Therese Peffer - Contestar

    The iOpener worked just fine for me. Had to keep it on for a few minutes. I also was able to get the suction cup seal right close to the edge, over top of the home button for added leverage. Used the blue tool and transitioned to the spudger. Slow, steady pressure…and patience. ;)

    johnhall918 - Contestar

    Unable to open an iPhone 7 display assembly. Used gell pack at 150 degrees F. The phone wouldn’t budge when I used the iFixit suction cut. Part of the problem is that the cup doesn’t adhere for long before it looses suction. I suspect it would work better on unbroken glass, but that doesn’t help me now. After spending a lot of time at this, I changed heating methods to a hot air heater. I raised the temp of the bottom end of the phone to, ultimately, 175 degrees, and used a variety of tools to try to pry the glass apart enough to get a spudger (or anything) in, but it didn’t even lift enough for a double-edged razor blade to get in. I’ve been trying this for hours now, and about to give up and throw a lot more money at this to have a service perform the work. I figured that 175 was as high as I should need to go to soften the adhesive without damaging the electronics. Should I have gone higher? I see no mention of measured temps in any instructions or comments.

    ted - Contestar

    Have you tried applying tape to the broken screen? This will help a lot with keeping the suction cup on it.

    Christian Groothuis -

    It doesn’t need to get very hot; pulling up on the display is mainly what does the trick. Make sure the two pentalobe screws have been removed and then try the tricks in this step. If all else fails, superglue the suction cup to your display and let it cure, and then pull. Keep in mind you only need a tiny gap to insert a plastic pick and start cutting the adhesive. Good luck!

    Jeff Suovanen -

    Just a question. After this operation the impermeability function was compromitted?

    bentek86 - Contestar

  5. Desliza el spudger a la izquierda a lo largo del borde inferior del iPhone. Gira el spudger para ampliar el espacio entre la pantalla y la carcasa trasera. Gira el spudger para ampliar el espacio entre la pantalla y la carcasa trasera.
    • Desliza el spudger a la izquierda a lo largo del borde inferior del iPhone.

    • Gira el spudger para ampliar el espacio entre la pantalla y la carcasa trasera.

  6. Desliza el spudger por el lado izquierdo del iPhone, comenzando en el borde inferior y deslizando hacia los botones de control de volumen y el interruptor de silencio. No hagas palanca en el borde superior del teléfono, corres el riesgo de dañar los clips de plástico que sujetan la pantalla. No hagas palanca en el borde superior del teléfono, corres el riesgo de dañar los clips de plástico que sujetan la pantalla.
    • Desliza el spudger por el lado izquierdo del iPhone, comenzando en el borde inferior y deslizando hacia los botones de control de volumen y el interruptor de silencio.

    • No hagas palanca en el borde superior del teléfono, corres el riesgo de dañar los clips de plástico que sujetan la pantalla.

  7. Inserta el borde plano de un spudger en la esquina inferior derecha del dispositivo. Gira el spudger para ampliar el espacio entre el ensamblaje de la pantalla y la caja trasera. Desliza el extremo plano del spudger por el lado derecho del teléfono para romper el adhesivo que sostiene la pantalla en su lugar.
    • Inserta el borde plano de un spudger en la esquina inferior derecha del dispositivo.

    • Gira el spudger para ampliar el espacio entre el ensamblaje de la pantalla y la caja trasera.

    • Desliza el extremo plano del spudger por el lado derecho del teléfono para romper el adhesivo que sostiene la pantalla en su lugar.

  8. Levanta la ventosa para levantar la pantalla y abra el iPhone. No levantar la pantalla más de 10º ya que hay cables planos  a lo largo del borde derecho del dispositivo que conecta la pantalla con la placa lógica.
    • Levanta la ventosa para levantar la pantalla y abra el iPhone.

    • No levantar la pantalla más de 10º ya que hay cables planos a lo largo del borde derecho del dispositivo que conecta la pantalla con la placa lógica.

    do not pull up pull sideways it will brake

    Riley Patterson - Contestar

    Made this mistake

    rachael.grime - Contestar

  9. Kits de Reparación de Batería de MacBook Air

    A partir de $69.99

    Buy Now

    Kits de Reparación de Batería de MacBook Air

    A partir de $69.99

    Buy Now
  10. Tira hacia arriba de la pequeña protuberancia en la ventosa para sacarla del panel frontal.
    • Tira hacia arriba de la pequeña protuberancia en la ventosa para sacarla del panel frontal.

  11. Desliza una púa de apertura a lo largo del borde superior del iPhone, entre la caja trasera y el panel frontal, para romper el adhesivo restante que sujeta la pantalla en su lugar. Tenga cuidado de no dañar los clips de plástico en el borde superior del teléfono.
    • Desliza una púa de apertura a lo largo del borde superior del iPhone, entre la caja trasera y el panel frontal, para romper el adhesivo restante que sujeta la pantalla en su lugar.

    • Tenga cuidado de no dañar los clips de plástico en el borde superior del teléfono.

  12. Tira del ensamblaje de la pantalla ligeramente hacia afuera desde el borde superior del teléfono para desenganchar los clips que lo sujetan a la caja posterior. Abre el iPhone moviendo la pantalla hacia arriba desde el lado izquierdo, como la tapa posterior de un libro. No intentes separar por completo la pantalla todavía, ya que hay varios cables frágiles que aún la conectan a la placa lógica del iPhone.
    • Tira del ensamblaje de la pantalla ligeramente hacia afuera desde el borde superior del teléfono para desenganchar los clips que lo sujetan a la caja posterior.

    • Abre el iPhone moviendo la pantalla hacia arriba desde el lado izquierdo, como la tapa posterior de un libro.

    • No intentes separar por completo la pantalla todavía, ya que hay varios cables frágiles que aún la conectan a la placa lógica del iPhone.

    I just broke the cable to the battery!

    No Bama - Contestar

    same dude im such a freak lol omg haha

    Aiden Polaski - Contestar

    Are there replacements ribbons?

    Blax Bently - Contestar

    Has anyone else noticed very small squares of rubber with a circle cut through it (I think they fall off into the phone when dismantling)?

    I just replaced my screen and worked out that these are actually a wee pocket that slips over the pentalobe screw holes on the replacement screen. I’m not sure if it’s an additional water resisting mechanism or if it’s to add additional traction for the screws

    richarddillon - Contestar

    Thanks, I was wondering where those were from!

    Albert -

    I just broke cable connecting camera and earpiece speaker to logic board. Be careful with it.

    Natan Haładyn - Contestar

    This section is missing a critical step - to lay some Post-It notes or something below the right half of the phone when you swing it open, so the ribbon cables don’t get sliced by the sharp edge of the phone case. I broke the Home Button ribbon cable because there was no strain relief when I laid it open.

    neila - Contestar

    I also broke the home button cable and now I have to use assistive touch.

    Laurencio Gonzalez - Contestar

  13. Retira los siguientes tornillos triples Y000 del soporte del conector inferior:
    • Retira los siguientes tornillos triples Y000 del soporte del conector inferior:

    • Tres tornillos de 1.2 mm

    • Un tornillo de 2.4 mm

    • Durante esta reparación, lleva cuenta de cada tornillo y asegúrate de que cada tornillo vuelva al lugar exacto de donde salió para evitar dañar tu iPhone.

    Ahhh shoot! accidentally ordered tri-wing vs tri-point (must have just looked for y000).. It seems they only did this to annoy repair folks because not everything is tri-point on the phone...

    Steve - Contestar

    These screws just spin for me. They don't back out, but the heads aren't stripped either. I've tried applying backpressure to help lift the screws, but no luck

    Jeff Hurst - Contestar

    The Y000 took out one of the screws but not the other 3. I even tried the PH000 as suggested but nothing.

    dbright - Contestar

    What driver do I need to remove these screws i’m stuck

    Nasser Nader - Contestar

    i cant use, the Y000 it isnt working.

    joscarlos91 - Contestar

    What if I stripped a screw what do I do??

    Jacob Ramos - Contestar

    Yep, only the 2.4mm came out, other 3 won’t budge, and worried I’ve stripped the heads. Anyone got any ideas?

    Stephen Babbage - Contestar

    It’s the screwdriver bit that is the problem. I had the same issue with 2 Y000 bits not grabbing the screw properly. I fixed it by using a small 3 sided file to slightly grind the groves in the Y000 bit just a bit deeper. Then the bit worked like a charm on these screws.

    Jim Staples - Contestar

    Use Y000 on all 4. U have to be very sensitive on the 1.2mm screws. Put the bit in the screw, put the left pointing finger on top of the screwdriver and turn the driver carefully to the right until you feel a “bump”, thats the trick :-), then you are able to screw the screw out.

    Magne Eivindson - Contestar

    For me the key here was a LOT of downward pressure to ensure the Y000 bit caught in the screw. Not sure i can describe how much exactly, but is was significant. Otherwise the bit would not catch.

    Erik Fredriksen - Contestar

    What do I do if I Stripped one of them?

    Adam Corral - Contestar

    Can’t get them removed what to do ?

    cowling_luke - Contestar

    Managed to get the central one out. The upper one won't move, the lower one I've popped out with some force. This allows you to rotate the cover enough to unplug the various bits. Not ideal, but works. I've tried applying a lot of pressure, using the tighten/ loosen method, but the heads have just got mashed… no wonder Samsung are now No1, sigh…

    jimpoolio - Contestar

    You need to be careful when just rotating the cover as you can accidentally slice through the two black antennas! You only need to nip them…As you can tell I have done this in the past :/

    Kyle Webb -

  14. Retira el soporte del conector inferior.
    • Retira el soporte del conector inferior.

    my battery cable connector was stuck to the bottom of this metal bracket plate so be careful when you lift it off

    Josh Martin - Contestar

    This may have been intentionally done by Apple to make sure the battery gets disconnected before any other connector is disconnected. So always make sure to disconnect the battery before disconnecting and reconnecting the connectors for the display.

    Oscar Moreno - Contestar

  15. Usa la punta de un spudger para sacar el conector de la batería de su zócalo en la placa lógica. Dobla el cable del conector ligeramente hacia arriba para evitar que haga contacto con el zócalo y suministra energía al teléfono. Dobla el cable del conector ligeramente hacia arriba para evitar que haga contacto con el zócalo y suministra energía al teléfono.
    • Usa la punta de un spudger para sacar el conector de la batería de su zócalo en la placa lógica.

    • Dobla el cable del conector ligeramente hacia arriba para evitar que haga contacto con el zócalo y suministra energía al teléfono.

  16. Asegúrate de que la batería esté desconectada antes de desconectar o reconectar los cables en este paso. Utiliza la parte plana de un spudger o tu uña  para desconectar los dos conectores inferiores de la pantalla haciendo palanca  hacia arriba de sus puertos de conexión en la placa lógica. Para reconectar estos cables, presiona un extremo hasta que encaje en su lugar, luego repite en el extremo opuesto. No presiones en el medio. Si el conector está ligeramente mal alineado, el conector se puede doblar y causar daño permanente.
    • Asegúrate de que la batería esté desconectada antes de desconectar o reconectar los cables en este paso.

    • Utiliza la parte plana de un spudger o tu uña para desconectar los dos conectores inferiores de la pantalla haciendo palanca hacia arriba de sus puertos de conexión en la placa lógica.

    • Para reconectar estos cables, presiona un extremo hasta que encaje en su lugar, luego repite en el extremo opuesto. No presiones en el medio. Si el conector está ligeramente mal alineado, el conector se puede doblar y causar daño permanente.

    • Si tienes un pantalla en blanco, líneas blancas en la pantalla, o no tienes respuesta táctil completa o parcial después de volver a ensamblar tu teléfono, intenta desconectar y reconectar con cuidado ambos cables y asegúrate de que estén encajados completamente.

  17. Remueve los dos tornillos Phillips 1.3mm que aseguran el soporte sobre el conector del sensor del panel frontal. Retira el soporte. Retira el soporte.
    • Remueve los dos tornillos Phillips 1.3mm que aseguran el soporte sobre el conector del sensor del panel frontal.

    • Retira el soporte.

    Has anyone had trouble getting these two screws off? I’ve been working on these for about 10 minutes and the LEFT screw wont spin. It seems like the little PH000 screwdriver bit won’t even grip it. (The one of the right comes off, no problem)

    It looks like I’ll have to pick this project up again with a screwdriver that will actually take off this piece.

    Makana Sylva - Contestar

    The right screw kept spinning, tried different levels of force but didn’t work. I left the screw on and bent the shield to get to the cable.

    s h - Contestar

    I used a #1 flat head tip to loosen.

    Peter Pearson - Contestar

    I couldn’t get the two screws out either—used the correct screw tip and everything. Stripped the screw. Will now attempt to just keep the cable attached…..

    Therese Peffer - Contestar

    Use the PH000 and apply a little more force before spinning, should come right out!

    Sierra Scolaro - Contestar

    ^To anyone having trouble, this is the correct answer. Put the phone on a firm surface, align your driver carefully, press down hard, and twist. As long as your driver is approximately the right size, it’ll come out.

    Jeff Suovanen -

    the two screw i have are stripped and i have n way of getting either screws off whats my next bet

    Alexis Marie Colon - Contestar

    The PH000 bit is to large. I can’t get the screws out either which really sucks…now I have to put everything back together, find another bit that will work and try this again another day. Not impressed with IFIXIT’s attention to detail so far :-(

    Ryan Welborn - Contestar

    Using iFixit’s driver kit, I prefer a PH00 for this, which is larger than the PH000. If you think the PH000 is too big, something is wrong.

    Jeff Suovanen -

    I think part of the issue with the iFixit PH000 is that it is slightly too pointy. The PH00 fits better because the splines engage the slots of the screw before the point bottoms out. The PH000 tip bottoms out in the screw’s center point and the splines don’t engage as well. I have other PH000 tips that are more blunt nose and they work better than the iFixit bit.

    rcarswell - Contestar

  18. Desconecta el conector del sensor del panel frontal de su puerto de conexión con la placa lógica. Este conector a presión  debe ser reconectado al finalizar en el mismo momento para minimizar el riesgo de que se doble.
    • Desconecta el conector del sensor del panel frontal de su puerto de conexión con la placa lógica.

    • Este conector a presión debe ser reconectado al finalizar en el mismo momento para minimizar el riesgo de que se doble.

    Das ist sehr mutig, das Kabel dort so zu strapazieren.

    Mich würde das Display daneben stellen und mit irgendetwas stützen, dass es nicht umkippen kann um Beschädigungen an dem Kabel zu vermeiden. Das reißt sehr schnell ein.

    Detlef Menninger - Contestar

  19. Retira el ensamblaje de la pantalla.

    When removing the screen, be aware of the two tiny square black rubber grommets on the Penelope screw brackets that secure the screen. They can fall off very easily and be lost without even knowing it (it happened to me, but was lucky enough to find them).

    Guy Cooley - Contestar

  20. Remueve los dos tornillos Phillips que aseguran la ventanilla del sensor barométrico a la parte trasera de la carcasa.
    • Remueve los dos tornillos Phillips que aseguran la ventanilla del sensor barométrico a la parte trasera de la carcasa.

  21. Remueve la ventanilla. Remueve la ventanilla.
    • Remueve la ventanilla.

  22. Usa el extremo plano de un spudger para desconectar el conector de motor táptico de  su zócalo en la placa lógica. Usa el extremo plano de un spudger para desconectar el conector de motor táptico de  su zócalo en la placa lógica.
    • Usa el extremo plano de un spudger para desconectar el conector de motor táptico de su zócalo en la placa lógica.

  23. Remueve los tornillos de 1.6 mm Phillips que sujetan el Motor Táptico a la caja trasera.
    • Remueve los tornillos de 1.6 mm Phillips que sujetan el Motor Táptico a la caja trasera.

    My screws are stripped here. Please help, I don’t know what to do!

    Salva Alcón - Contestar

    My screws are also stripped here, but the phone has never been opened before!

    Kyle Webb - Contestar

    Hey Salva and Kyle, sorry to hear about all these stripped screws! For help with removing them, check out our guide.

    Adam O'Camb - Contestar

  24. Remueve el Motor Táptico. Remueve el Motor Táptico.
    • Remueve el Motor Táptico.

Conclusión

Para volver a ensamblar tu dispositivo, sigue estas instrucciones en orden inverso.

48 personas más completaron esta guía.

Un agradecimiento especial a estos traductores:

100%

¡ Mariana nos está ayudando a reparar el mundo! ¿Quieres contribuir?
Empezar a traducir ›

Evan Noronha

Miembro Desde 05/02/15

168,895 Reputación

177 Guías creadas

Equipo

iFixit Miembro de iFixit

Community

98 Miembros

9,004 Guías creadas

Good job and prof.

Firasss Alhuseniy - Contestar

Bravo!!!!!!!!¡!

omanvaal - Contestar

Thank you for your amazing instruction, it was my first phone repair ever! iPhone is fully functional again!

Christopher Saunders - Contestar

were can I buy one tapic Engine?

playabeach - Contestar

Hi! In our store the Taptic Engine is just called an iPhone 7 Vibrator. It's linked at the top of the guide, or you can find it here.

Adam O'Camb -

About the warning (Opening the iPhone 7 will damage the waterproof seals on the display. If you do not replace the adhesive seals, your phone will function normally, but will no longer be water-resistant). How do I replace the adhesive seals? where can I get them?

Angel Jonathan - Contestar

@angeljonathan The parts and instructions for replacing the adhesive are linked in Step 18.

Jeff Suovanen -

Hi! I changed Taptic Engine for new but same problem, doesn’t work. Can you help us? Thanks!

Tom - Contestar

I replaced the taptic engine and I also replaced the dock connector, but it stll doesn’t work. I smell apple fuckary… i swear this company is just plain evil…

jordyshujaa2 - Contestar

I changed Taptic Engine for new but same problem, doesn’t work.

Has this worked for others ?

Locked by apple like their HB ?

toshahin - Contestar

Does anyone know if the phone (iphone 7) will run like normal without the taptic engine?

Julio - Contestar

Answered it myself. YES.

Removed it just now and it is up and running fine.

I will update after a week to confirm.

No need to remove battery either, leave the screen attached and the battery in, start with the barometric vent.

Highly recommend this mod.

Julio - Contestar

Hey everyone.

While doing this repair, I have damaged the connector between the screen and the iphone (shown in step number 15)

The result is that my home button is not working anymore.

Now how can I repair that? what sould I replace ? the whole screen? another part?

Thanks

Maxim - Contestar

Will it harm iphone to use device without the Taptic Engine?

jasontrunzo - Contestar

Agregar Comentario

Ver Estadísticas:

Ultimas 24 Horas: 45

Últimos 7 Días: 312

Últimos 30 Días: 1,397

Todo El Tiempo: 64,341