Saltar al contenido principal

Repara tus cosas

Derecho a reparar

Partes y herramientas

Introducción

Usa esta guía para ayudar a reemplazar una panel inferior roto, gastado o rayado en tu MacBook Pro 15" con pantalla retina de mediados de 2015.

  1. Quitar los siguientes tornillos pentalobe P5 que sujetan la cubierta del  MacBook Pro:
    • Quitar los siguientes tornillos pentalobe P5 que sujetan la cubierta del MacBook Pro:

    • Ocho 3.1 mm

    • Dos 2.3 mm

    The number of screws listed here is wrong on my model. I had four of the smaller size.

    anonymous 1286 - Contestar

    Just to add to my comment above (I can't edit it because it's anonymous), my MacBook Pro is a mid-2015 15in model 2.8GHz (A1398; EMC2881). For the bottom case it uses six 3.1mm screws, and four 2.3mm screws at the clutch/hinge side of the MacBook Pro. I tried using a 3.1mm screw at the clutch/hinge end, as described in the main article, and they don't fit. It has to be four 2.3mm screws.

    anonymous 1286 - Contestar

    WAIT!.. STOP.

    iFixit has had a slew of defective batteries that they will require you take out and return (after gluing them in). Search on: "Battery percentage suddenly drops" here on this site. This process is 50 steps to get the new battery in, and another 50 to put all the parts back. For $199, Apple will do the whole repair, warranty it, and also replace the trackpad and the keyboard (because it's easier for THEM to do).

    Ifixit WILL NOT stand behind defective batteries unless you spend another 4-6 hours swapping in a new one. NOT. WORTH. IT. See posts here (Battery percentage suddenly drops from ~60% to 7%) on frustrated customer’s multiple attempts and class-action lawsuits.

    MFMauceri - Contestar

    Thank you for this info, you’ve probably saved a lot of time, and hassle (myself included, if I end up going through with this repair).

    Andrew Poindexter -

    The instructions below have you basically taking ALL of the guts out of case. I’ve been doing my own apple repairs since before ifixit was a thing and this one is a handful. My battery was swelling and I wanted to remove it before it burst or bent the case so I took it out without having a replacement and it occurs to me that aside from using the solvent (liquid) to remove the adhesive, you could probably do this only taking the trackpad ribbon out. I have mine reassembled now and will research the best battery to buy but I think installation will take about 5 minutes. See if you can slip a plastic gift card under the battery and wag/saw the adhesive out without the solvent before you go through all of this. It might work. Note, don’t bend or put too much stress on the battery and certainly don’t puncture it…

    br1ansk - Contestar

  2. Kit de Destornilladores Manta

    112 bits for every fix.

    Upgrade Your Toolbox

    Kit de Destornilladores Manta

    Upgrade Your Toolbox
  3. Levantando desde el borde más cercano a la articulación de la tapa, levanta la cubierta del Macbook Pro. Levantando desde el borde más cercano a la articulación de la tapa, levanta la cubierta del Macbook Pro.
    • Levantando desde el borde más cercano a la articulación de la tapa, levanta la cubierta del Macbook Pro.

  4. La cubierta tiene dos clavijas de plástico (rojo) que entran en dos clips de plástico en la caja superior (naranja). Durante el reensamblaje, suavemente empuja hacia abajo, el centro de la cubierta para volver a fijar la caja a sus dos clips de plástico. Durante el reensamblaje, suavemente empuja hacia abajo, el centro de la cubierta para volver a fijar la caja a sus dos clips de plástico.
    • La cubierta tiene dos clavijas de plástico (rojo) que entran en dos clips de plástico en la caja superior (naranja).

    • Durante el reensamblaje, suavemente empuja hacia abajo, el centro de la cubierta para volver a fijar la caja a sus dos clips de plástico.

    pretty hard to put it back, so I just remove the clips on the upper case....

    jamiegan835 - Contestar

    The trick to putting it back on is to guide your fingers to the same level as the clips, and then when you put the case down move your hand from the left side of the case to the right side of the case; applying pressure when you reach the area where the clips are.

    Aaron Freidus - Contestar

Conclusión

Para volver a ensamblar tu dispositivo, sigue estas instrucciones en orden inverso.

18 personas más completaron esta guía.

Un agradecimiento especial a estos traductores:

100%

Estos traductores nos están ayudando a reparar el mundo! ¿Quieres contribuir?
Empezar a traducir ›

Equipo

iFixit Miembro de iFixit

Community

116 Miembros

11,204 Guías creadas

Do we need two different screw drivers for this or is the recommended one enough?

Jamey Rassweiler - Contestar

You need the recommended one for the lid an a torx T5 for the screws inside

Oros -

hello i have a 2015 15” macbook pro nut i want them all custom to me so scraped off the paint to be clear back. ive seen many “clear looking stickers but they mostly look $@$*!&. have you herd of any copany selling a clearback housing and can only find stickers do you knaw any sites delling vlear hpusings?. the only other thing i can think of if have a friend #D print in clear and polish it till turns clear any ideas? i also wany yje top case vlrar slso but oe thing at a time

jae.good - Contestar

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 31

Ultimos 7 días: 260

Ultimos 30 días: 1,181

Todo El Tiempo: 29,232