Saltar al contenido principal

Razer DeathAdder Chroma USB Cable Replacement

Qué necesitas

  1. Razer DeathAdder Chroma USB Cable Replacement, Outer Casing: paso 1, imagen 1 de 1
    • Opening the mouse casing will void any warranty that exists for the mouse.

    • Turn the mouse over so the bottom is facing up.

  2. Razer DeathAdder Chroma USB Cable Replacement: paso 2, imagen 1 de 2 Razer DeathAdder Chroma USB Cable Replacement: paso 2, imagen 2 de 2
    • Use the blunt end of the spudger to pry the adhesive rubber pads from the top left and right edges.

  3. Razer DeathAdder Chroma USB Cable Replacement: paso 3, imagen 1 de 2 Razer DeathAdder Chroma USB Cable Replacement: paso 3, imagen 2 de 2
    • Use a Phillips #0 screwdriver to remove two 6.7 mm screws.

  4. Razer DeathAdder Chroma USB Cable Replacement: paso 4, imagen 1 de 1
    • Use your fingers to identify the location of the screw under the bottom label.

  5. Razer DeathAdder Chroma USB Cable Replacement: paso 5, imagen 1 de 1
    • Use a Phillips #0 screwdriver to remove one 6.7 mm screw.

    • Clear the label away from around the screw for easier removal.

  6. Razer DeathAdder Chroma USB Cable Replacement: paso 6, imagen 1 de 3 Razer DeathAdder Chroma USB Cable Replacement: paso 6, imagen 2 de 3 Razer DeathAdder Chroma USB Cable Replacement: paso 6, imagen 3 de 3
    • Turn the mouse over so the bottom is facing down.

    • Separate the top casing from the bottom base by pulling the top casing upwards.

    • Separating the casing too quickly could damage the ribbon connector between the motherboard and the LED lights.

  7. Razer DeathAdder Chroma USB Cable Replacement: paso 7, imagen 1 de 2 Razer DeathAdder Chroma USB Cable Replacement: paso 7, imagen 2 de 2
    • Disconnect the ribbon connector between the motherboard and the LED lights by pulling upward.

    • Pulling too hard could damage the wire connections.

  8. Razer DeathAdder Chroma USB Cable Replacement, Motherboard: paso 8, imagen 1 de 2 Razer DeathAdder Chroma USB Cable Replacement, Motherboard: paso 8, imagen 2 de 2
    • Disconnect the ribbon connector between the motherboard and the USB cable by pulling upward.

    There are 2 tiny locking pins at the back you may need to spudge the connector casing a bit on each side to release these , I did.

    John bayley - Contestar

  9. Razer DeathAdder Chroma USB Cable Replacement: paso 9, imagen 1 de 1
    • Use a Phillips #0 screwdriver to remove three 5.5 mm screws.

  10. Razer DeathAdder Chroma USB Cable Replacement: paso 10, imagen 1 de 2 Razer DeathAdder Chroma USB Cable Replacement: paso 10, imagen 2 de 2
    • Use a Phillips #0 screwdriver to remove two 11.5 mm screws on the side buttons.

  11. Razer DeathAdder Chroma USB Cable Replacement: paso 11, imagen 1 de 1
    • Use a Phillips #000 screwdriver to remove one 5.0 mm screw.

    Does anyone know what the circuitry this screw holds in place does, I completely missed this tiny screw and accidently snapped the 2 soldered components off named D2 & D3… But the mouse still works fine ?? however i do not use razer synapse anymore so i dont know if its 100% working

    woolstarr - Contestar

    Never mind it just came to my attention there is a set of LEDs in the mouse wheel which is what that tiny board is, soo …. RIP Mouse Wheel LEDs

    woolstarr - Contestar

  12. Razer DeathAdder Chroma USB Cable Replacement: paso 12, imagen 1 de 2 Razer DeathAdder Chroma USB Cable Replacement: paso 12, imagen 2 de 2
    • Disconnect the ribbon connector between the motherboard and the optical sensor.

  13. Razer DeathAdder Chroma USB Cable Replacement: paso 13, imagen 1 de 2 Razer DeathAdder Chroma USB Cable Replacement: paso 13, imagen 2 de 2
    • Remove the motherboard by grasping the sides and gently pulling upward.

  14. Razer DeathAdder Chroma USB Cable Replacement, USB Cable: paso 14, imagen 1 de 1
    • Locate the USB cable.

  15. Razer DeathAdder Chroma USB Cable Replacement: paso 15, imagen 1 de 2 Razer DeathAdder Chroma USB Cable Replacement: paso 15, imagen 2 de 2
    • Remove the USB cable by pulling it up and out.

Conclusión

To reassemble your device, follow these instructions in reverse order.

7 personas más completaron esta guía.

Henry Shi

Miembro Desde 03/26/17

221 Reputación

1 Guía escrita

Equipo

Baylor, Team S5-G2, Williams Spring 2017 Miembro de Baylor, Team S5-G2, Williams Spring 2017

BU-WILLIAMS-S17S5G2

3 Miembros

6 Guías creadas

5 comentarios

Thank you! It realy worked. Btw: The cable for the Deathadder 2013 is working for the Chroma and Elite as well. I Just tried it :)

Pokefreeks - Contestar

Thanks for the advice

João Costa Santos -

Great and easy guide thanx alot, saved me a new mouse :)

jesperkb - Contestar

Is there a reliable website where I can get a replacement cable with low delivery time?

Bubbles EXE - Contestar

where can i get the cable from?

Mourya Singham - Contestar

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 4

Ultimos 7 días: 13

Ultimos 30 días: 42

Todo El Tiempo: 14,328