Saltar al contenido principal

RCA Voyager II RCT6773W22 Disassembly

Qué necesitas

  1. RCA Voyager II RCT6773W22 Disassembly, RCA Voyager II RCT6773W22 Disassembly: paso 1, imagen 1 de 1
    • Have Workstation Prepped

  2. RCA Voyager II RCT6773W22 Disassembly: paso 2, imagen 1 de 1
    • remove the two screws on the top of the device with a PH000 screwdriver

  3. RCA Voyager II RCT6773W22 Disassembly: paso 3, imagen 1 de 1
    • Starting from the top, place pick or plastic tool between the power button and screen edge and push apart slightly.

  4. RCA Voyager II RCT6773W22 Disassembly: paso 4, imagen 1 de 1
    • Run pick across the top to the right and then down the right side and around the rest of the tablet.

    • There is a good amount of space between the bezel and the board. Be gentle, but the risk of breaking components is low.

  5. RCA Voyager II RCT6773W22 Disassembly: paso 5, imagen 1 de 2 RCA Voyager II RCT6773W22 Disassembly: paso 5, imagen 2 de 2
    • lift section out of the black casing from the bottom, lift and remove by pulling away from tablet.

  6. RCA Voyager II RCT6773W22 Disassembly: paso 6, imagen 1 de 1
    • Battery connection (on older models, may be soldered to board)

    • Front Camera

    • Digitizer

    • LCD

    • Speaker

  7. RCA Voyager II RCT6773W22 Disassembly: paso 7, imagen 1 de 1
    • Remove battery Connection First

    • Do not use any metal tools while the battery is plugged in. It may cause a short.

  8. RCA Voyager II RCT6773W22 Disassembly: paso 8, imagen 1 de 1
    • unplug the speaker

  9. RCA Voyager II RCT6773W22 Disassembly: paso 9, imagen 1 de 3 RCA Voyager II RCT6773W22 Disassembly: paso 9, imagen 2 de 3 RCA Voyager II RCT6773W22 Disassembly: paso 9, imagen 3 de 3
    • Lift the black cover over all three flex cables (Camera, LCD, Digitizer) with a plastic tool.

    • The covers are incredibly fragile, and easy to break

    • gently disconnect all three cables with your fingers by pulling slightly

  10. RCA Voyager II RCT6773W22 Disassembly: paso 10, imagen 1 de 1
    • remove the three screws securing the board with your PH000 Screwdriver

  11. RCA Voyager II RCT6773W22 Disassembly: paso 11, imagen 1 de 2 RCA Voyager II RCT6773W22 Disassembly: paso 11, imagen 2 de 2
    • lift the board out gently

    • Do not tug the board out too hard, the antenna cable on the left is soldered in!

    • Fold board over the left side of the tablet and gently remove tape securing antenna to the case. Use a small amount of heat if necessary.

  12. RCA Voyager II RCT6773W22 Disassembly: paso 12, imagen 1 de 2 RCA Voyager II RCT6773W22 Disassembly: paso 12, imagen 2 de 2
    • remove tape from top and bottom of the battery.

    • with a plastic piece, lift battery from adhesive securing it in place.

    • do not use a metal or sharp tool to remove the battery, tearing or puncturing it may cause it to explode or heat rapidly, and may damage your device.

    • The battery is secured directly to the back of the LCD. Exercise caution while removing the battery not to damage the LCD.

    • The battery is soft and somewhat malleable - it can bend slightly without damage.

  13. RCA Voyager II RCT6773W22 Disassembly: paso 13, imagen 1 de 2 RCA Voyager II RCT6773W22 Disassembly: paso 13, imagen 2 de 2
    • Place picks between the lcd and the plastic clips holding it in place.

    • The pick placement to the top left side (near the power button) is smaller and on a corner. I recommend inserting this pick last.

  14. RCA Voyager II RCT6773W22 Disassembly: paso 14, imagen 1 de 1
    • Gently push top right pick down to lift LCD from the clip. Run across the top and right side to further lift LCD.

    • Use picks as needed to separate LCD in other areas.

  15. RCA Voyager II RCT6773W22 Disassembly: paso 15, imagen 1 de 1
    • Once separated and loose, remove picks so you do not damage the LCD while removing it.

    • To remove, lift top of LCD and pull out of case away from the speaker, which is fixed to the digitizer frame.

  16. RCA Voyager II RCT6773W22 Disassembly: paso 16, imagen 1 de 2 RCA Voyager II RCT6773W22 Disassembly: paso 16, imagen 2 de 2
    • to remove Digitizer/Glass from the frame and speaker, slide a pick under a corner between the glass and frame to loosen adhesive

    • If you're having issues loosening the adhesive, use a heat gun around the edges, then try again.

  17. RCA Voyager II RCT6773W22 Disassembly: paso 17, imagen 1 de 1
    • You have completely dismantled the RCA Voyager II

Conclusión

To reassemble your device, follow these instructions in reverse order.

35 personas más completaron esta guía.

Chris

Miembro Desde 01/11/16

2,022 Reputación

1 Guía escrita

31 comentarios

what is that flat part that has the little copper bar in the middle. What do you call that?

TheUnchanted Sword - Contestar

The LCD has a piece of copper tape on it, is that what you mean?

Sam Goldheart -

Nice Guide. Very Simple and Easy to follow!

Aerial L - Contestar

Bonne site merci pour tous je suis très heureux content que entrer dans ce site

diego jamal - Contestar

Anyone know which company made this very fragile digitizer for RCA Voyager?

Spock Chen - Contestar

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 0

Ultimos 7 días: 4

Ultimos 30 días: 25

Todo El Tiempo: 21,546