Repara tus cosas Comunidad Tienda

Protocol Videodrone AP Battery Wiring Replacement

Introducción

This guide will show you how to replace the battery and the soldering new wires to the motherboard. This is guide includes a highly recommend soldering guide. CAUTION: Soldering iron will be hot and may cause minor burns if handles improperly.

Qué necesitas

  1. Protocol Videodrone AP Battery Wiring Replacement, Battery Wiring: paso 1, imagen 1 de 1

    • Make sure the drone is turned off

    Editar

  2. Protocol Videodrone AP Battery Wiring Replacement: paso 2, imagen 1 de 1

    • Open the hatch and carefully pull out the battery to expose the cable connection

    Editar

  3. Protocol Videodrone AP Battery Wiring Replacement: paso 3, imagen 1 de 2 Protocol Videodrone AP Battery Wiring Replacement: paso 3, imagen 2 de 2

    • Carefully pull apart the cable connection

    Editar

  5. Protocol Videodrone AP Battery Wiring Replacement: paso 4, imagen 1 de 2 Protocol Videodrone AP Battery Wiring Replacement: paso 4, imagen 2 de 2

    • Unscrew the 4 screws from the bottom of the drone.

    • Unscrew the 8 screws connecting the propeller guards to the drone

    • Unscrew the four propeller screws.

    • One screw is hidden behind the screwdriver.

    Editar

  6. Protocol Videodrone AP Battery Wiring Replacement: paso 5, imagen 1 de 1

    • Carefully remove faulty battery wiring from the drone

    Editar

  7. Protocol Videodrone AP Battery Wiring Replacement: paso 6, imagen 1 de 1

    • Feed through opening using tweezers to grasp the wire and carefully pull through.

    Editar

  8. Protocol Videodrone AP Battery Wiring Replacement: paso 7, imagen 1 de 1

    • Use the soldering iron to solder new wires to mother board. CAUTION: Soldering iron may get hot and cause minor burns if handled improperly.

    • Use this guide for how to solder: https://www.youtube.com/watch?v=QKbJxytE...

    Editar

  9. Protocol Videodrone AP Battery Wiring Replacement: paso 8, imagen 1 de 1

    • Reattach the battery and test for power by turning on the drone and look for the 4 LEDs turn on.

    Editar
Conclusión

All Done!

Una persona más ha completado esta guía.

Autor

con 4 otros colaboradores

Serge

Miembro Desde 09/26/17

340 Reputación

3 Guías creadas

Insignias: 8

+ 5 más insignias

Equipo

USF Tampa, Team S2-G1, Passmore Fall 2017 Miembro de USF Tampa, Team S2-G1, Passmore Fall 2017

USFT-PASSMORE-F17S2G1

4 Miembros

3 Guías creadas

3 comentarios

Great explanation. Just wondering where to get the replacement piece. My drone has the black wire hanging by a single strand just outside the white connector. The red wire is in tact but I would need the whole part that attaches to the board and extends outside the drone to connect the battery to. Thanks

yasureok - Contestar

Was wondering i think its charging the blue light flashes when plugged in but wont turn on. Wires look brand new

Michael Landry - Contestar

I’m wondering the same thing, mine lights up blue when charging, wires look good but still no action.

Ryann Hunter -

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 0

Ultimos 7 días: 2

Ultimos 30 días: 6

Todo El Tiempo: 1,761