Repara tus cosas Comunidad Tienda

Protocol Dronium III AP Camera Replacement

Introducción

This guide explains how to replace the Protocol Dronium III AP Camera.

Qué necesitas

  1. Protocol Dronium III AP Camera Replacement, Drone Battery Pack: paso 1, imagen 1 de 2 Protocol Dronium III AP Camera Replacement, Drone Battery Pack: paso 1, imagen 2 de 2

    • Ensure the drone is powered off.

    • Press in and lift battery compartment cover.

    • A soft pry tool may be used for easier access.

    Editar

  2. Protocol Dronium III AP Camera Replacement: paso 2, imagen 1 de 1

    • Remove battery pack from body of drone.

    Editar

  3. Protocol Dronium III AP Camera Replacement: paso 3, imagen 1 de 2 Protocol Dronium III AP Camera Replacement: paso 3, imagen 2 de 2

    • Disconnect white connectors between the battery pack and drone.

    Editar

  4. Protocol Dronium III AP Camera Replacement, Camera: paso 4, imagen 1 de 1

    • Remove the eight (8) 5mm screws attaching the motor arms to the body using a JIS #00 screwdriver.

    Editar

  6. Protocol Dronium III AP Camera Replacement: paso 5, imagen 1 de 2 Protocol Dronium III AP Camera Replacement: paso 5, imagen 2 de 2

    • Remove the six (6) 5mm screws attaching the Body Cover to the Body of the drone using a JIS #00 screwdriver.

    • Remove the Body Cover.

    Editar

  7. Protocol Dronium III AP Camera Replacement: paso 6, imagen 1 de 2 Protocol Dronium III AP Camera Replacement: paso 6, imagen 2 de 2

    • Remove the two (2) 5mm screws attaching the Motherboard to the body of the drone using a JIS #00 screwdriver.

    • Lift the Motherboard off the mounting position.

    • Do not pull hard on the Motherboard as solder connections are fragile.

    Editar

  8. Protocol Dronium III AP Camera Replacement: paso 7, imagen 1 de 1
    Herramienta utilizada en este paso:
    Tweezers
    $4.99
    Comprar

    • Remove the tape covering the camera with the tweezers.

    Editar

  9. Protocol Dronium III AP Camera Replacement: paso 8, imagen 1 de 2 Protocol Dronium III AP Camera Replacement: paso 8, imagen 2 de 2

    • Remove the plastic holding the ribbon cable connector with the tweezers.

    • Be careful with the ribbon cable, it is easy to damage.

    Editar

  10. Protocol Dronium III AP Camera Replacement: paso 9, imagen 1 de 1

    • Move the ribbon cable out of the way with the Spuger.

    Editar

  11. Protocol Dronium III AP Camera Replacement: paso 10, imagen 1 de 2 Protocol Dronium III AP Camera Replacement: paso 10, imagen 2 de 2

    • Remove the camera by gently prying it out of the bracket with the spudger.

    Editar
Conclusión

To reassemble your device, follow these instructions in reverse order.

Autor

con 5 otros colaboradores

Steven Mooers

Miembro Desde 10/18/17

401 Reputación

4 Guías creadas

Insignias: 4

+1 mas insignia

Equipo

UW Tacoma, Team S1-G1, Rose Fall 2017 Miembro de UW Tacoma, Team S1-G1, Rose Fall 2017

UWT-ROSE-F17S1G1

4 Miembros

4 Guías creadas

0 comentarios

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 0

Ultimos 7 días: 1

Ultimos 30 días: 4

Todo El Tiempo: 287