Saltar al contenido principal

PowerLead Puto PLD003 Zoom Button Replacement

Qué necesitas

  1. PowerLead Puto PLD003 Zoom Button Replacement, Side Panel: paso 1, imagen 1 de 1
    • Slide the battery eject button open to release the battery door.

  2. PowerLead Puto PLD003 Zoom Button Replacement: paso 2, imagen 1 de 1
    • With the battery door open, carefully remove all four 5 mm Phillips #1 screws.

  3. PowerLead Puto PLD003 Zoom Button Replacement: paso 3, imagen 1 de 1
    • Rotate the camera so that the underside is facing up.

    • Remove the four 5 mm Phillips #1 screws.

  4. PowerLead Puto PLD003 Zoom Button Replacement: paso 4, imagen 1 de 1
    • Place the camera on a flat surface, with its underside facing you.

    • Gently pull up on the side panel to remove it from the camera.

  5. PowerLead Puto PLD003 Zoom Button Replacement, Zoom Button: paso 5, imagen 1 de 2 PowerLead Puto PLD003 Zoom Button Replacement, Zoom Button: paso 5, imagen 2 de 2
    • Remove the 4 mm Phillips #1 screws holding the weight.

    • Remove the weight.

  6. PowerLead Puto PLD003 Zoom Button Replacement: paso 6, imagen 1 de 1
    • Remove the two 4 mm Phillips #1 screws holding the back panel in place.

  7. PowerLead Puto PLD003 Zoom Button Replacement: paso 7, imagen 1 de 1
    • Apply pressure to the back panel, pulling away from the camera to remove it.

  8. PowerLead Puto PLD003 Zoom Button Replacement: paso 8, imagen 1 de 2 PowerLead Puto PLD003 Zoom Button Replacement: paso 8, imagen 2 de 2
    • Remove the final 4 mm Phillips #1 screw holding the screen in place.

    • This screw is very small and hard to see.

  9. PowerLead Puto PLD003 Zoom Button Replacement: paso 9, imagen 1 de 1
    • Carefully apply pressure away from the camera to the screen to detach it from the body.

    • The white cord should still be connected to the body.

    • OPTIONAL: Remove the screen to make accessing the zoom button easier.

  10. PowerLead Puto PLD003 Zoom Button Replacement: paso 10, imagen 1 de 1
    • Remove the three 4 mm Phillips #1 screws holding the top panel in place.

  11. PowerLead Puto PLD003 Zoom Button Replacement: paso 11, imagen 1 de 2 PowerLead Puto PLD003 Zoom Button Replacement: paso 11, imagen 2 de 2
    • Push upward on the top panel to remove it from the body of the camera.

  12. PowerLead Puto PLD003 Zoom Button Replacement: paso 12, imagen 1 de 2 PowerLead Puto PLD003 Zoom Button Replacement: paso 12, imagen 2 de 2
    • Remove the two 4 mm Phillips #1 screws holding the circuit board in place.

    • Do not remove the silver screws.

  13. PowerLead Puto PLD003 Zoom Button Replacement: paso 13, imagen 1 de 1
    • Lift the circuit board out of the plastic casing.

    • Gently pull on the zoom button to remove it from the circuit board.

Conclusión

To reassemble your device, follow these instructions in reverse order.

0 comentarios

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 0

Ultimos 7 días: 0

Ultimos 30 días: 2

Todo El Tiempo: 159