Repara tus cosas Comunidad Tienda

PowerLead Puto PLD003 Lens Replacement

Introducción

This guide shows how to remove the side panel from the camera, how to remove the back panel, and how to replace the lens.

Qué necesitas

  1. PowerLead Puto PLD003 Lens Replacement, Side Panel: paso 1, imagen 1 de 1

    • Slide the battery eject button open to release the battery door.

    Editar

  2. PowerLead Puto PLD003 Lens Replacement: paso 2, imagen 1 de 1

    • With the battery door open, carefully remove all four 5 mm Phillips #1 screws.

    Editar

  3. PowerLead Puto PLD003 Lens Replacement: paso 3, imagen 1 de 1

    • Rotate the camera so that the underside is facing up.

    • Remove the four 5 mm Phillips #1 screws.

    Editar

  4. PowerLead Puto PLD003 Lens Replacement: paso 4, imagen 1 de 1

    • Place the camera on a flat surface, with its underside facing you.

    • Gently pull up on the side panel to remove it from the camera.

    Editar

  5. PowerLead Puto PLD003 Lens Replacement, Lens: paso 5, imagen 1 de 2 PowerLead Puto PLD003 Lens Replacement, Lens: paso 5, imagen 2 de 2

    • Remove the three 4 mm Phillips #1 screws holding the weight.

    • Remove the weight.

    Editar

  7. PowerLead Puto PLD003 Lens Replacement: paso 6, imagen 1 de 1

    • Remove the two 4 mm Phillips #1 screws holding the back panel in place.

    Editar

  8. PowerLead Puto PLD003 Lens Replacement: paso 7, imagen 1 de 1

    • Apply pressure to the back panel (away from the camera) to remove.

    Editar

  9. PowerLead Puto PLD003 Lens Replacement: paso 8, imagen 1 de 1

    • Set aside back panel for now.

    • Remove the final 4 mm Phillips #1 screw holding the screen in place. It is very small and hard to see.

    Editar

  10. PowerLead Puto PLD003 Lens Replacement: paso 9, imagen 1 de 1

    • Carefully apply pressure, away from the camera, to the screen to detach it from the body.

    • The white cord should still be connected to the body.

    • OPTIONAL: Remove the screen to make accessing the lens easier

    Editar

  11. PowerLead Puto PLD003 Lens Replacement: paso 10, imagen 1 de 1

    • Unscrew the two 4 mm Phillips #1 screws holding onto the lens casing

    • There are also two 4 mm Phillips #1 screws on the other side holding onto the lens casing, remove them as well.

    Editar

  12. PowerLead Puto PLD003 Lens Replacement: paso 11, imagen 1 de 1

    • Pull forward on the lens casing to remove it. The cord connecting the light to the motherboard should still be attached.

    Editar

  13. PowerLead Puto PLD003 Lens Replacement: paso 12, imagen 1 de 1

    • Unscrew the three 4 mm Phillips #1 screws holding the plastic lens holder.

    Editar

  14. PowerLead Puto PLD003 Lens Replacement: paso 13, imagen 1 de 1

    • Remove the plastic lens holder.

    Editar

  15. PowerLead Puto PLD003 Lens Replacement: paso 14, imagen 1 de 1

    • Push the lens out of the plastic casing from the back.

    • Insert new lens into the plastic casing.

    Editar
Conclusión

To reassemble your device, follow these instructions in reverse order.

0 comentarios

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 0

Ultimos 7 días: 1

Ultimos 30 días: 1

Todo El Tiempo: 164