Esta versión puede contener ediciones incorrectas. Cambie a la última instantánea verificada.
Qué necesitas
-
-
Ubique la lengüeta de liberación de la batería en la parte inferior del G4.
-
Deslice la lengüeta de liberación de la batería hacia la izquierda y levante la batería de la computadora.
-
-
-
Gire el tornillo de bloqueo del teclado ubicado en el medio del teclado para que quede paralelo a la barra espaciadora. Una media vuelta de paralelo a paralelo lo desbloqueará. Otra media vuelta lo volverá a bloquear.
-
Tire de las pestañas de liberación del teclado hacia usted y levante el teclado hasta que se libere.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Release the tabs on each side of the RAM chip at the same time. These tabs lock the chip in place and releasing them will cause the chip to "pop" up.
-
Pull the RAM chip out.
-
Repeat this process if a second RAM chip is installed.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the seven T8 Torx screws from the lower case.
-
Using your thumbs, slide the lower case toward the front of the computer.
-
The lower case may stick in the front on a tab just above the center of the optical drive. Be careful as you work the case off, or you may break the thin strip of plastic just above the drive.
-
Lift the lower case off.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Firmly grasp the plastic tab attached to the Airport card and pull up and to the left.
-
Disconnect the antenna cable from the left side of the Airport card.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Disconnect the hard drive ribbon from the logic board using a spudger or the tip of your finger.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
To free the hard drive, remove the two T8 Torx screws from the right wall of the battery housing.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the hard drive by lifting the left edge up and out of the computer.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Disconnect and remove the indicated orange ribbon cable.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Disconnect the pink and white inverter cable from the inverter board.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the two silver T8 Torx screws from the black plastic bar.
-
Lift the black plastic bar out.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Disconnect the two orange connectors from the logic board, removing tape as necessary.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Lift the drive up on the right side so that you can access and disconnect the modem cable and inverter cable.
-
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the drive by lifting the right edge up and out of the computer.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Disconnect the large DC-In connector from the right side of the logic board.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Lift the DC-In board out of the computer by pulling up and away from you.
-
If there is a fan present, rotate the DC-In board slightly clockwise before easing it out at a slight angle in order to clear the fan clamp on top of it.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Before continuing, place a soft cloth on your work surface to rest the computer on. Turn the G4 over and place it on the cloth.
-
Disconnect the four indicated connectors from the logic board.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Disconnect the two connectors from the modem filter board.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the T6 Torx screw from the modem filter board.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the modem filter board from the computer by pulling up and to the right.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Turn the G4 over.
-
Remove the seven T8 Torx screws from the logic board.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Disconnect the 5 indicated connectors from the logic board, removing tape as necessary.
-
Reassembly Tip: Reseating the logic board will be much easier if you use kapton tape to hold these five connectors out of the way until it is in place.
-
Caution: If taping the connectors back, be careful not to use tape with anything but very weak adhesive (i.e. kapton tape). Even electrical tape can pull the paint off the hinges when removed.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Carefully lift the logic board up and pull it away from you.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the two T8 Torx screws that secure the PC Card cage.
-
Remove the 4 mm hex nut from the PC Card cage.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the PC Card cage by pulling it to the right and twisting slightly toward you.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the four black T8 Torx screws from the plastic framework.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Turn the G4 over.
-
Remove the five silver T8 Torx screws from the metal framework.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Turn the G4 over.
-
Grasp the plastic framework and pull directly up.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Disconnect and remove the pink and white inverter cable, removing tape as necessary.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Disconnect the audio connector cable on the right side of the computer.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Position the display approximately at a 45 degree angle and rest the computer on a soft cloth with the back panel ports facing up.
-
Remove the two T8 Torx screws from each clutch cover.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Close the display and pull off both clutch covers. You can use a non-metal flathead screwdriver if the clutch covers do not come off easily.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Open the back panel port cover and remove the four T6 Torx screws.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Open the display to a 90 degree angle. Rest the trackpad face down on your work surface and allow the display to hang over the edge. If possible, adjust your chair or worksurface height so the display will rest on your legs and the trackpad will lie flat on the worksurface.
-
Remove the four T8 Torx screws which fasten the display to the trackpad. The screw closest to the display data cable has a tapered head.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Grasp the metal heat exchanger and pull up and away from you. You may need to move the inverter cable on the right side of the computer in order to rotate the heat exchanger.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Lift up the metal brackets on either side of the upper case.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Carefully thread the inverter cable on the right side through the slot in the upper case.
-
Carefully thread the display and backlight cables individually through the slot in the upper case. Be very careful with the display cable as it is easily damaged.
-
Remove the display assembly.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Re-align the metal heat exchanger with the upper case. Reconnect the audio connector cable on the right side of the upper case.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Use a spudger to pry the PRAM battery out of its housing on the upper case. Make sure not to bend the PRAM battery too much while prying it out.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Your upper case should look approximately like this.
-
Cancelar: No complete esta guía.
6 personas más completaron esta guía.