Saltar al contenido principal
  1. Ubique la lengüeta de liberación de la batería en la parte inferior del G4. Deslice la lengüeta de liberación de la batería hacia la izquierda y levante la batería de la computadora.
    • Ubique la lengüeta de liberación de la batería en la parte inferior del G4.

    • Deslice la lengüeta de liberación de la batería hacia la izquierda y levante la batería de la computadora.

  2. Este paso está sin traducir. Ayuda a traducirlo

    Remove the seven T8 Torx screws from the lower case. Using your thumbs, slide the lower case toward the front of the computer.
    • Remove the seven T8 Torx screws from the lower case.

    • Using your thumbs, slide the lower case toward the front of the computer.

    • The lower case may stick in the front on a tab just above the center of the optical drive. Be careful as you work the case off, or you may break the thin strip of plastic just above the drive.

    • Lift the lower case off.

  3. Este paso está sin traducir. Ayuda a traducirlo

    Disconnect the hard drive ribbon from the logic board using a spudger or the tip of your finger.
    • Disconnect the hard drive ribbon from the logic board using a spudger or the tip of your finger.

  4. Este paso está sin traducir. Ayuda a traducirlo

    To free the hard drive, remove the two T8 Torx screws from the right wall of the battery housing.
    • To free the hard drive, remove the two T8 Torx screws from the right wall of the battery housing.

  5. Este paso está sin traducir. Ayuda a traducirlo

    Remove the hard drive by lifting the left edge up and out of the computer.
    • Remove the hard drive by lifting the left edge up and out of the computer.

    • There are four rubber bumpers that fit over the hard drive screws. Ensure that these bumpers come out when you remove the hard drive.

  6. Este paso está sin traducir. Ayuda a traducirlo

    Your laptop should look approximately like this.
    • Your laptop should look approximately like this.

  7. Este paso está sin traducir. Ayuda a traducirlo

    Disconnect and remove the indicated orange ribbon cable.
    • Disconnect and remove the indicated orange ribbon cable.

  8. Este paso está sin traducir. Ayuda a traducirlo

    Disconnect the pink and white inverter cable from the inverter board.
    • Disconnect the pink and white inverter cable from the inverter board.

    • The display inverter has orange plastic shielding around it that looks similar to the tape used elsewhere within the computer. Do not remove the shielding from the inverter.

  9. Este paso está sin traducir. Ayuda a traducirlo

    Remove the two silver T8 Torx screws from the black plastic bar.
    • Remove the two silver T8 Torx screws from the black plastic bar.

    • Lift the black plastic bar out.

    • Reassembly will be significantly easier if you reseat the hard drive before returning the black bar to its place.

  10. Este paso está sin traducir. Ayuda a traducirlo

    Disconnect the two orange connectors from the logic board, removing tape as necessary.
    • Disconnect the two orange connectors from the logic board, removing tape as necessary.

  11. Este paso está sin traducir. Ayuda a traducirlo

    Lift the drive up on the right side so that you can access and disconnect the modem cable and inverter cable.
    • Lift the drive up on the right side so that you can access and disconnect the modem cable and inverter cable.

  12. Este paso está sin traducir. Ayuda a traducirlo

    Remove the drive by lifting the right edge up and out of the computer.
    • Remove the drive by lifting the right edge up and out of the computer.

Linea de Meta

6 personas más completaron esta guía.

Documentos Adjuntos

iRobot

Miembro Desde 24/09/09

1 Reputación

647 Guías creadas

0 comentarios

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 0

Ultimos 7 días: 1

Ultimos 30 días: 1

Todo El Tiempo: 9,765