Saltar al contenido principal

Esta versión puede contener ediciones incorrectas. Cambiar a la última instantánea verificada.

Qué necesitas

  1. , Bateria: paso 1, imagen 1 de 2 , Bateria: paso 1, imagen 2 de 2
    • Ubique la lengüeta de liberación de la batería en la parte inferior del G4.

    • Deslice la lengüeta de liberación de la batería hacia la izquierda y levante la batería de la computadora.

  2. , teclado: paso 2, imagen 1 de 1
    • Gire el tornillo de bloqueo del teclado ubicado en el medio del teclado para que quede paralelo a la barra espaciadora. Una media vuelta de paralelo a paralelo lo desbloqueará. Otra media vuelta lo volverá a bloquear.

    • Tire de las pestañas de liberación del teclado hacia usted y levante el teclado hasta que se libere.

  3. : paso 3, imagen 1 de 1
    • Descanse el teclado boca abajo en el área del trackpad.

    • Desconecte el conector del teclado de la placa lógica.

  4. : paso 4, imagen 1 de 1
    • Su computadora portátil debe verse aproximadamente como si

  5. Este paso está sin traducir. Ayuda a traducirlo

    : paso 5, imagen 1 de 1
    • Release the tabs on each side of the RAM chip at the same time. These tabs lock the chip in place and releasing them will cause the chip to "pop" up.

    • Pull the RAM chip out.

    • Repeat this process if a second RAM chip is installed.

  6. Este paso está sin traducir. Ayuda a traducirlo

    : paso 6, imagen 1 de 2 : paso 6, imagen 2 de 2
    • Remove the seven T8 Torx screws from the lower case.

    • Using your thumbs, slide the lower case toward the front of the computer.

    • The lower case may stick in the front on a tab just above the center of the optical drive. Be careful as you work the case off, or you may break the thin strip of plastic just above the drive.

    • Lift the lower case off.

  7. Este paso está sin traducir. Ayuda a traducirlo

    : paso 7, imagen 1 de 1
    • Firmly grasp the plastic tab attached to the Airport card and pull up and to the left.

    • Disconnect the antenna cable from the left side of the Airport card.

  8. Este paso está sin traducir. Ayuda a traducirlo

    : paso 8, imagen 1 de 1
    • Disconnect the hard drive ribbon from the logic board using a spudger or the tip of your finger.

  9. Este paso está sin traducir. Ayuda a traducirlo

    : paso 9, imagen 1 de 1
    • To free the hard drive, remove the two T8 Torx screws from the right wall of the battery housing.

  10. Este paso está sin traducir. Ayuda a traducirlo

    : paso 10, imagen 1 de 1
    • Remove the hard drive by lifting the left edge up and out of the computer.

    • There are four rubber bumpers that fit over the hard drive screws. Ensure that these bumpers come out when you remove the hard drive.

  11. Este paso está sin traducir. Ayuda a traducirlo

    : paso 11, imagen 1 de 1
    • Your laptop should look approximately like this.

  12. Este paso está sin traducir. Ayuda a traducirlo

    : paso 12, imagen 1 de 1
    • Disconnect and remove the indicated orange ribbon cable.

  13. Este paso está sin traducir. Ayuda a traducirlo

    : paso 13, imagen 1 de 1
    • Disconnect the pink and white inverter cable from the inverter board.

    • The display inverter has orange plastic shielding around it that looks similar to the tape used elsewhere within the computer. Do not remove the shielding from the inverter.

  14. Este paso está sin traducir. Ayuda a traducirlo

    : paso 14, imagen 1 de 1
    • Remove the two silver T8 Torx screws from the black plastic bar.

    • Lift the black plastic bar out.

    • Reassembly will be significantly easier if you reseat the hard drive before returning the black bar to its place.

  15. Este paso está sin traducir. Ayuda a traducirlo

    : paso 15, imagen 1 de 1
    • Disconnect the two orange connectors from the logic board, removing tape as necessary.

  16. Este paso está sin traducir. Ayuda a traducirlo

    : paso 16, imagen 1 de 1
    • Lift the drive up on the right side so that you can access and disconnect the modem cable and inverter cable.

  17. Este paso está sin traducir. Ayuda a traducirlo

    : paso 17, imagen 1 de 1
    • Remove the drive by lifting the right edge up and out of the computer.

  18. Este paso está sin traducir. Ayuda a traducirlo

    : paso 18, imagen 1 de 1
    • Disconnect the large DC-In connector from the right side of the logic board.

  19. Este paso está sin traducir. Ayuda a traducirlo

    : paso 19, imagen 1 de 1
    • Remove the two T6 Torx screws from the DC-In board.

  20. Este paso está sin traducir. Ayuda a traducirlo

    : paso 20, imagen 1 de 1
    • Lift the DC-In board out of the computer by pulling up and away from you.

    • If you don't have a 667 MHz computer, there is a fan in this location which makes it a bit difficult to remove the DC-In board.

    • If there is a fan present, rotate the DC-In board slightly clockwise before easing it out at a slight angle in order to clear the fan clamp on top of it.

  21. Este paso está sin traducir. Ayuda a traducirlo

    : paso 21, imagen 1 de 1
    • Before continuing, place a soft cloth on your work surface to rest the computer on. Turn the G4 over and place it on the cloth.

    • Disconnect the four indicated connectors from the logic board.

    • The large multicolor cable may be difficult to free.

    • The top center cable may not need to be disconnected to remove the modem filter board. It connects to the logic board fan to its immediate left, which is attached to the logic board itself.

  22. Este paso está sin traducir. Ayuda a traducirlo

    : paso 22, imagen 1 de 1
    • Remove the T8 Torx screw near the heat pipe.

  23. Este paso está sin traducir. Ayuda a traducirlo

    : paso 23, imagen 1 de 1
    • Disconnect the two connectors from the modem filter board.

    • To the immediate right of the modem filter board, the heatsink has two sets of five fins with a double-wide space in between them. This space is where the gray & black coiled wire is supposed to go to ensure a flush fit.

  24. Este paso está sin traducir. Ayuda a traducirlo

    : paso 24, imagen 1 de 1
    • Remove the T6 Torx screw from the modem filter board.

  25. Este paso está sin traducir. Ayuda a traducirlo

    : paso 25, imagen 1 de 1
    • Remove the modem filter board from the computer by pulling up and to the right.

    • There is a small plastic post which helps hold the modem filter board in place. You need to clear this post to remove the modem filter board from the computer.

  26. Este paso está sin traducir. Ayuda a traducirlo

    : paso 26, imagen 1 de 1
    • Turn the G4 over.

    • Remove the seven T8 Torx screws from the logic board.

    • The five black screws go on the right side of the logic board, the large silver screw goes at the top, and the small silver screw is located on the left side.

  27. Este paso está sin traducir. Ayuda a traducirlo

    : paso 27, imagen 1 de 1
    • Disconnect the 5 indicated connectors from the logic board, removing tape as necessary.

    • Reassembly Tip: Reseating the logic board will be much easier if you use kapton tape to hold these five connectors out of the way until it is in place.

    • Caution: If taping the connectors back, be careful not to use tape with anything but very weak adhesive (i.e. kapton tape). Even electrical tape can pull the paint off the hinges when removed.

  28. Este paso está sin traducir. Ayuda a traducirlo

    : paso 28, imagen 1 de 1
    • Carefully lift the logic board up and pull it away from you.

    • This step requires some force, but if the logic board will not come up, make sure that you have removed all the necessary screws and connectors. Warming the heatsink with a heatgun or blow dryer will help release the logic board.

    • On 800 MHz and above G4s, you must disconnect the fan cable from the logic board before you lift the board entirely off.

  29. Este paso está sin traducir. Ayuda a traducirlo

    : paso 29, imagen 1 de 1
    • Your laptop should look approximately like this.

Linea de Meta

19 personas más completaron esta guía.

Documentos Adjuntos

iRobot

Miembro Desde 09/24/09

1 Reputación

636 Guías creadas

2 comentarios

just a small detail i guess..

in the intro to this guide it says "The motherboard - which includes all ports but not the DC-In board - is fairly easy to change."

and right next says : "Difficulty: Difficult"

just sayin'..

Cheers!

rotarypot - Contestar

C'est tellement petit que j'ai arraché un condensateur à cause du tournevis qui a dérapé... -_- Du coup je l'ai ressoudé :) mais je sais pas si ca va marcher... :/

Tristan Jestin - Contestar

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 0

Ultimos 7 días: 2

Ultimos 30 días: 29

Todo El Tiempo: 24,018