Esta versión puede contener ediciones incorrectas. Cambiar a la última instantánea verificada.
Qué necesitas
-
Este paso está sin traducir. Ayuda a traducirlo
-
Use your thumbs to push the two battery retaining tabs away from the battery.
-
The battery should pop up enough to rotate it toward yourself and lift it out of the lower case.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the three 2.3 mm Phillips screws securing the memory cover to the lower case.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Lift the memory cover slightly and pull it toward yourself to remove it from the lower case.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the following ten screws:
-
Two 14.7 mm shouldered Phillips.
-
Three 12.3 mm Phillips.
-
One 3.8 mm T8 Torx.
-
One 6.8 mm T8 Torx.
-
Three 1.3 mm Phillips.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Use your fingernails to separate the ZIF cable lock away from its socket. (Move the two brown bits down 1mm)
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Use the tip of a spudger to slide the trackpad ribbon cable out of its socket.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the four 3.4 mm Phillips screws from the PC card side of the PowerBook.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the four 3.4 mm Phillips screws from the DVI connector side of the PowerBook.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Depress the display latch release button and open your display.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Starting near the display, lift the upper case straight up off the lower case, minding any cables that may get caught.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
If necessary, remove the strip of tape covering the speaker cables.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Use your fingernails or the tip of a spudger to separate the ZIF cable lock from its socket.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Pull the DC-in ribbon cable straight away from its socket.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Peel the DC-in cable off the adhesive securing it to the lower case.
-
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
If necessary, use the tip of a spudger to remove the small piece of foam tape from the side of the left speaker.
-
De-route the AirPort antenna cables from the channel in the left speaker.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the single 6.9 mm T8 Torx screw securing the left speaker to the lower case.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Lift the left speaker from its rear edge and maneuver it out of the lower case, minding the cables sitting in the channel near the front edge of the left speaker.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the single 6.9 mm T8 Torx screw securing the speaker cable ground loop to the lower case.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Peel back the piece of foil tape covering the modem cable to free the speaker cable held underneath.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Pull the speaker cable straight up to disconnect it from the sound card.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Use the flat end of a spudger to pry the hard drive ribbon cable connector up off the logic board.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Use the flat end of a spudger to pry the sound card cable connector up off the logic board.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Use the flat end of a spudger to pry the optical drive cable connector up off the logic board.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Use your fingernails or the tip of a spudger to separate the ZIF cable lock from its socket.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Pull the PRAM battery & USB board cable out of its socket.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Use a spudger to de-route the display data cable from the channel in the right speaker.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Use the tip of a spudger to pry the power button LED window off the right speaker.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the single T8 6.9 mm Torx screw securing the right speaker to the lower case.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
De-route the speaker cable from the clips along the front edge of the logic board.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Close your PowerBook, minding any cables that may interfere, and flip it over.
-
Disconnect the power cable connector by pulling it straight away from its socket on the logic board.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Disconnect the battery cable connector straight away from its socket on the logic board.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Use the flat end of a spudger to pry the AirPort/Bluetooth cable connector up off the logic board.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Use the flat end of a spudger to pry the modem cable connector up off the logic board.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Use the flat end of a spudger to pry the PC card cage cable connector up off the logic board.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Disconnect both of the following connectors from the logic board:
-
Left fan cable.
-
Inverter cable.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the following four screws securing the optical drive to the lower case:
-
Three 6.8 mm T8 Torx.
-
One 3.8 mm T8 Torx.
-
Lift the optical drive out of the lower case, minding any cables that may get caught.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
If necessary, remove the piece of tape securing the display data cable to the logic board.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Pull the display data cable away from its socket to disconnect it from the logic board.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Disconnect the right fan by pulling its connector away from the socket on the logic board.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the following 12 screws:
-
Three black 5.7 mm T8 Torx.
-
Three 7 mm T8 Torx with spring washers.
-
Three 6.8 mm T8 Torx.
-
Three 3.8 mm T8 Torx.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
If necessary, use a spudger to pry up the left edge of the logic board to separate the solidified thermal paste from the heat sink.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Lift the logic board from its left edge and rotate it toward the right side of the lower case.
-
Rotate the logic board until it is nearly vertical, and wiggle it around until it releases from the lower case.
-