Esta versión puede contener ediciones incorrectas. Cambie a la última instantánea verificada.
Qué necesitas
-
Este paso está sin traducir. Ayuda a traducirlo
-
Use your thumbs to push the two battery retaining tabs away from the battery.
-
The battery should pop up enough to rotate it toward yourself and lift it out of the lower case.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the three 2.3 mm Phillips screws securing the memory cover to the lower case.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Lift the memory cover slightly and pull it toward yourself to remove it from the lower case.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the following ten screws:
-
Two 14.7 mm shouldered Phillips.
-
Three 12.3 mm Phillips.
-
One 3.8 mm T8 Torx.
-
One 6.8 mm T8 Torx.
-
Three 1.3 mm Phillips.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Use your fingernails to separate the ZIF cable lock away from its socket. (Move the two brown bits down 1mm)
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Use the tip of a spudger to slide the trackpad ribbon cable out of its socket.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the four 3.4 mm Phillips screws from the PC card side of the PowerBook.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the four 3.4 mm Phillips screws from the DVI connector side of the PowerBook.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Depress the display latch release button and open your display.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Starting near the display, lift the upper case straight up off the lower case, minding any cables that may get caught.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
If necessary, peel back the strip of aluminum tape covering the modem cable.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Use the flat end of a spudger to pry the modem cable connector up off the modem.
-
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Use a 4 mm nut driver to remove the two nuts securing the modem to the PC card cage.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Lift the modem straight up off the studs on the PC card cage.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Use the flat end of a spudger to pry the hard drive cable connector up off the logic board.
-
Bend the hard drive cable away from the PC card cage, giving yourself room to remove it.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Use the flat end of a spudger to pry the PC card cage connector up off the logic board.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Use the tip of a spudger to peel back the small strip of copper tape off the edge of the PC card cage near the side of the lower case.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the four Phillips screws (2- 4 mm & 2 -6.8 mm ) securing the PC card cage to the lower case.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Lift the PC card cage by its center piece and maneuver it out of the lower case.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Use the flat end of a spudger to pry the ribbon cable connector up off the AirPort/Bluetooth board.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the single 2.1 mm Phillips screw securing the AirPort/Bluetooth bracket to the lower case.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Use the flat end of a spudger to pry the AirPort/Bluetooth board up off the adhesive securing it to the lower case.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
If necessary, remove the piece of tape and EMI foam covering the AirPort/Bluetooth antennas.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Use the flat end of a spudger to pry both antenna connectors up off the AirPort/Bluetooth board.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Pull the display data cable away from its socket to disconnect it from the logic board.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
If necessary, use the tip of a spudger to remove the small piece of foam tape from the side of the left speaker.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
De-route both AirPort/Bluetooth antennas and the inverter cable from underneath the DC-in board ribbon cable.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove four T6 Torx screws from the left display hinge. 2- 8 mm and 1 -10 mm and one 6 mm left to right.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove four T6 Torx screws from the right display hinge. 2- 8 mm and 1 -10 mm and one 6 mm right to left.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
While supporting the display with one hand, remove the one remaining T6 10 mm Torx screw from each display bracket (two screws total).
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Lift the display straight up from the lower case, minding any cables that may get caught.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
A small bracket (shown in red) near either side of the clutch cover is free to rotate about the display hinge and must be inserted behind the heat sink framework for the display to seat properly.
-
Before completely lowering the display onto the lower case, use a spudger to rotate the bracket toward the rear edge of your PowerBook, and insert the bracket between the heat sink framework and the adjacent spring. The second picture shows the bracket correctly installed.
-
When removing the display screws, keep track of the thin metal bracket (shown in green) under the screws on the inner display bracket.
-
The outer display bracket (shown in orange) simply slides onto the spiral display spring. Be sure to press it on before installing your display into the lower case.
-
Cancelar: No complete esta guía.
5 personas más completaron esta guía.