Saltar al contenido principal

Esta versión puede contener ediciones incorrectas. Cambiar a la última instantánea verificada.

Qué necesitas

  1. , Batería: paso 1, imagen 1 de 1
    • Usa una moneda para girar el tronillo de bloqueo de batería 90 grados a la derecho.

    • Saca la batería de la computadora.

  2. , EMI Finger: paso 2, imagen 1 de 1
    • Retira los cuatro tornillos Phillips en la compuerta de la memoria.

    • Desliza la puerta de la memoria fuera del compartimiento de la memoria.

  3. : paso 3, imagen 1 de 1
    • Retira el largo tornillo negro Phillips que esta a lado de la tarjeta de memoria.

    • Retira el pequeño EMI finger debajo del tornillo negro.

  4. , Teclado: paso 4, imagen 1 de 1
    • En el teclado retira las teclas F1, F2, F11 y F12.

    • Esto es peligroso - respira profunda antes de continuar. Coloca tu dedo índice debajo de la esquina superior izquierda de la teclado y levántala hasta que oigas un click. Después mueve tu dedo al borde izquierdo de la tecla y levántalo para sacar la tecla.

    • Estas liberando las dos pestañas en el lado izquierdo de la tecla de dos pequeños agujeros en el mecanismo de tijeras de plástico.

    • Cuando reemplaces las teclas en el teclado, coloca la tecla directamente sobre el slot donde irá y presiona hacia abajo hasta que oigas que la tecla entra en su lugar.

  5. : paso 5, imagen 1 de 1
    • Usa tu uña o la pequeña cabeza plana de un desarmador para despegar los stickers grises que cubren cada tornillo.

  6. : paso 6, imagen 1 de 1
    • Retira los dos tornillos Phillips pequeños.

  7. : paso 7, imagen 1 de 1
    • Levanta el teclado por las teclas 'esc' y'eject' y levántalo con cuidado hasta que este vertical.

  8. : paso 8, imagen 1 de 1
    • Toma el conector plano del teclado cerca del conector y desconéctalo de la tarjeta lógica.

  9. Este paso está sin traducir. Ayuda a traducirlo

    : paso 9, imagen 1 de 1
    • Remove the three 2.5mm Phillips screws from within the battery compartment.

  10. Este paso está sin traducir. Ayuda a traducirlo

    : paso 10, imagen 1 de 1
    • Turn the computer 90 degrees clockwise and remove the two Phillips screws from the casing.

    • Outside case screws are aprox. 1/4 in long

  11. Este paso está sin traducir. Ayuda a traducirlo

    : paso 11, imagen 1 de 1
    • Turn the computer 90 degrees clockwise again, and remove only the bottom screw on either side of the hinge.

  12. Este paso está sin traducir. Ayuda a traducirlo

    : paso 12, imagen 1 de 1
    • Turn the computer 90 degrees clockwise just one more time, and remove the two Phillips screws on the exterior wall of the battery compartment.

    • Note: For reassembly the two screws have long necks.

  13. Este paso está sin traducir. Ayuda a traducirlo

    : paso 13, imagen 1 de 1
    • Turn the computer over and open it up.

    • Remove the following 14 screws:

    • Six 2.5 mm Phillips on either side of the keyboard area.

    • Five 4.5 mm Phillips on the left half of the keyboard area.

    • One 7 mm hex in the upper left corner of the upper case (a T6 Torx driver will do the job nicely).

    • One 15 mm Phillips in the upper middle of the keyboard area.

    • One 16.5 mm hex in the upper right of the upper case (again, a T6 Torx driver will work well).

  14. Este paso está sin traducir. Ayuda a traducirlo

    : paso 14, imagen 1 de 1
    • This step is extremely tricky, and has the potential to ruin your computer. It is easy to pull the plug with the red and black leads (the power) out of the motherboard. If you do that, it is nearly impossible to fix.

    • Peel up the two pieces of foil tape on the left side of the keyboard area.

    • The connectors at the ends of the cables are attached very firmly to the sockets on the logic board. Pulling directly on the cable will either separate the cable from its connector or the socket from the logic board.

    • Carefully disconnect the microphone and power cables from the logic board. Using your fingernails or a dental pick, carefully pry the connectors from their sockets. Make sure you're pulling only on the connector and not on the socket.

  15. Este paso está sin traducir. Ayuda a traducirlo

    : paso 15, imagen 1 de 1
    • Starting at one of the upper corners near the screen, work around the frame, separating the upper case from the lower case.

  16. Este paso está sin traducir. Ayuda a traducirlo

    : paso 16, imagen 1 de 1
    • Using a screw driver, gently release the two grey plastic clips inside the battery compartment in order to remove the right part of the upper case.

    • There are two more grey plastic clips holding the left part of the upper case. They are not easy to release as they are hidden from view prior to disassembly. They are in the same position as the two in the battery compartment, but on the opposite side of the trackpad. Try to stick a flat pry tool into the clip holes and push the clips inward (toward to screen) so they disengage and release the left part of the upper case.

    • Lift the upper case off the computer.

Linea de Meta

11 personas más completaron esta guía.

Documentos Adjuntos

iRobot

Miembro Desde 09/24/09

1 Reputación

636 Guías creadas

0 comentarios

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 0

Ultimos 7 días: 3

Ultimos 30 días: 12

Todo El Tiempo: 11,837