Esta versión puede contener ediciones incorrectas. Cambiar a la última instantánea verificada.
Qué necesitas
-
-
Usa una moneda para girar el tronillo de bloqueo de batería 90 grados a la derecho.
-
Saca la batería de la computadora.
-
-
-
Retira los cuatro tornillos Phillips en la compuerta de la memoria.
-
Desliza la puerta de la memoria fuera del compartimiento de la memoria.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Flip down the door on the right side of the battery compartment.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Use a spudger or flathead screwdriver to disconnect the Airport antenna from the card.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Grasp the plastic tab and pull the card out all the way.
-
-
-
En el teclado retira las teclas F1, F2, F11 y F12.
-
Esto es peligroso - respira profunda antes de continuar. Coloca tu dedo índice debajo de la esquina superior izquierda de la teclado y levántala hasta que oigas un click. Después mueve tu dedo al borde izquierdo de la tecla y levántalo para sacar la tecla.
-
Estas liberando las dos pestañas en el lado izquierdo de la tecla de dos pequeños agujeros en el mecanismo de tijeras de plástico.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the three 2.5mm Phillips screws from within the battery compartment.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Turn the computer 90 degrees clockwise and remove the two Phillips screws from the casing.
-
Outside case screws are aprox. 1/4 in long
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Turn the computer 90 degrees clockwise again, and remove only the bottom screw on either side of the hinge.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Turn the computer 90 degrees clockwise just one more time, and remove the two Phillips screws on the exterior wall of the battery compartment.
-
Note: For reassembly the two screws have long necks.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Turn the computer over and open it up.
-
Remove the following 14 screws:
-
Six 2.5 mm Phillips on either side of the keyboard area.
-
Five 4.5 mm Phillips on the left half of the keyboard area.
-
One 7 mm hex in the upper left corner of the upper case (a T6 Torx driver will do the job nicely).
-
One 15 mm Phillips in the upper middle of the keyboard area.
-
One 16.5 mm hex in the upper right of the upper case (again, a T6 Torx driver will work well).
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Peel up the two pieces of foil tape on the left side of the keyboard area.
-
Carefully disconnect the microphone and power cables from the logic board. Using your fingernails or a dental pick, carefully pry the connectors from their sockets. Make sure you're pulling only on the connector and not on the socket.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Starting at one of the upper corners near the screen, work around the frame, separating the upper case from the lower case.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Using a screw driver, gently release the two grey plastic clips inside the battery compartment in order to remove the right part of the upper case.
-
There are two more grey plastic clips holding the left part of the upper case. They are not easy to release as they are hidden from view prior to disassembly. They are in the same position as the two in the battery compartment, but on the opposite side of the trackpad. Try to stick a flat pry tool into the clip holes and push the clips inward (toward to screen) so they disengage and release the left part of the upper case.
-
Lift the upper case off the computer.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Peel back the yellow tape securing the inverter cable near the fan.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the following eight screws:
-
One 4.5 mm Phillips near the modem.
-
Three 6 mm Phillips near the display.
-
Two large 7.5 mm Phillips with attached springs.
-
Two 13 mm Phillips, one on the lower left side of the heat sink and one between the fan and the optical drive.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Peel up the Bluetooth cable on the right side of the fan.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Lift up the inverter cable with one hand, and carefully thread it around the heat sink. The inverter cable is still attached to the logic board, so be careful not to put too much strain on the cable.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Support the heat sink with both hands, and carefully lift it out of the computer. Be careful not to bend the copper heat pipe connecting the two sections of the heat sink.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the single Phillips screw securing the hall effect sensor board to the optical drive.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Deroute the cable connecting the hall effect sensor board to the DC-to-DC board.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Use a spudger or the tip of your finger to disconnect the hall effect sensor cable from the DC-to-DC board.
-
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Use the orange plastic loop to disconnect the hard drive cable from the logic board.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the two Phillips screws securing the hard drive bracket to the metal framework.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Use a spudger or the tip of your finger to disconnect the sleep light cable from the DC-to-DC board.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the following five secrews/standoffs from the DC-to-DC board:
-
One 3.5 mm Phillips in the lower right corner.
-
Two 3 mm Phillips on either side of the battery contacts.
-
One 10 mm Phillips in the upper right corner.
-
One 14 mm long 4 mm standoff in the upper left corner. You can remove this standoff either with a 4 mm nut driver or needlenose pliers.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the silver EMI fingers located near the battery contacts.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Use a spudger to pry up the end of the DC-to-DC board closest to the display and remove the board from the computer.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the three Phillips screws securing the modem and modem shield to the logic board.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Disconnect the modem from the logic board by lifting the bottom edge of the modem. Don't remove the modem entirely just yet as it is still connected to the RJ-11 board.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Carefully disconnect six indicated connectors from the logic board. To disconnect the four white connectors, use your fingernails or a dental pick to carefully pry the connectors from their sockets. Make sure you're pulling only on the connector and not on the socket.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Lift up middle speaker cable from the lower left corner of the fan, and disconnect the two sections of the cable.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Deroute the microphone cable from its channel in the metal framework.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the following nine screws:
-
Four 3 mm Phillips allong the left edge and near the fan.
-
One 4 mm Phillips in the bottom left corner.
-
Two 6 mm Phillips near the left hinge.
-
One 9 mm Phillips in the top left corner of the fan.
-
One 12 mm Phillips just above where the hard drive was located.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Peel up the yellow tape securing the display data cable to the metal framework, and deroute the display data cable from its slot in the framework.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the newly revealed Phillips screw near the RJ-11 board.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Lift the RJ-11 board up from the left side, and remove the single Phillips screw hidden beneath.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Lift up and remove the silver EMI fingers located above the ports on the left side of the computer.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Pull back on the orange optical drive cable with one hand, and use your other hand to lift the front section of the metal framework over the optical drive cable.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Deroute the microphone cable from its channel in the upper right corner of the framework.
-
The metal framework should now be free can be removed from the computer. Be careful when removing the metal framework that none of the cables get caught on the framework.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the two Phillips screws from the bottom right of the logic board.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Lift the logic board partly up from the optical side.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Disconnect the DC-In connector from the underside of the logic board.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the two 6mm Phillips screws from the upper right corner of the computer.
-
Remove the newly-liberated small metal bracket.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the two recessed Phillips screws on the right side of the optical drive.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Lift the optical drive up by its front left corner and pull it out of the computer.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Disconnect the multicolor connector by sliding it to the left.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Disconnect the silver bluetooth cable by pulling directly up.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the single Phillips screw from the right side of the board.
-
Lift the bluetooth board out of the computer.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Peel back the yellow tape from the right side of the subwoofer.
-
Remove the single Phillips screw from the right side of the subwoofer, under the tape you just removed.
-
Remove the yellow tape that secures the remaining cables to the side of the subwoofer.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Slide the subwoofer away from the screen and out of the computer.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Deroute the Airport Extreme antenna from the card slot and lower case, removing tape as necessary.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Place a cloth between the screen and the bottom case.
-
Close the bottom case and turn the laptop over.
-
Remove the two Phillips screws from the bottom case.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the two Phillips screws from either side of the display hinge.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Grasp the lower case and push down on the hinge side while rotating the other end of the case toward you until it pops free, then remove it entirely (leaving the display).
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the two T6 Torx screws in the lower left and lower right corners of the display securing the rear bezel to the display assembly.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Insert the spudger between the left edge of the front display bezel and the plastic strip attached to the rear bezel, with the edge of the tool angled toward the LCD.
-
Rotate the tool away from the LCD to pop the rear bezel off the tabs on the front display bezel.
-
Work along the left edge of the display until the rear bezel is evenly separated from the front bezel.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Insert a spudger between the right edge of the front display bezel and the plastic strip attached to the rear bezel, with the edge of the tool angled toward the LCD.
-
Rotate the tool away from the LCD to pop the rear bezel off the tabs on the front display bezel.
-
Work along the right edge of the display until the rear bezel is evenly separated from the front bezel.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Insert a spudger between the top edge of the front display bezel and the plastic strip attached to the rear bezel, with the edge of the tool angled toward the LCD.
-
Rotate the tool away from the LCD to pop the rear bezel off the tabs on the front display bezel.
-
Work along the top edge of the display until the rear bezel is evenly separated from the front bezel.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Insert a spudger in the space between the front bezel and the rear display bezel near the top left corner.
-
Release the clip by rotating the spudger away from the screen.
-
Repeat this process on the top right corner of the display.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Lift the top edge of the rear display bezel slightly.
-
Slide the rear display bezel away from you to undo the last few clips.
-
Rotate the rear display bezel off, and lay it next to the display.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Flip the device over and remove the two 4.5 mm Phillips screws on each side of the metal bracket (four screws in total).
-
Thread the display inverter, antenna, and display data cables through the bracket and remove the metal bracket.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Flip the device over.
-
Remove the 5.5 mm Phillips screw connecting the display inverter to the front display bezel.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Using the pointed end of a spudger, lift the display inverter out of the clutch cover.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the three 3.0 mm Phillips screws connecting the clutch cover to the front display bezel.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Pull the right edge of the clutch cover downwards.
-
Remove the clutch cover from the device.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Disconnect the inverter cable by pulling the connector away from the socket on the inverter board.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the two pieces of tape covering the display data cable.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Pull the display data cable connector away from its socket to disconnect it from the LCD.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the two 3.0 mm Phillips screws securing the LCD to the left side of the front display bezel.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the two 3.0 mm Phillips screws securing the LCD to the right side of the front display bezel.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Push the LCD away from the front display bezel.
-
Remove the LCD.
-