Saltar al contenido principal

Esta versión puede contener ediciones incorrectas. Cambiar a la última instantánea verificada.

Qué necesitas

  1. , Batería: paso 1, imagen 1 de 1
    • Usa una moneda para girar el tronillo de bloqueo de batería 90 grados a la derecho.

    • Saca la batería de la computadora.

  2. , EMI Finger: paso 2, imagen 1 de 1
    • Retira los cuatro tornillos Phillips en la compuerta de la memoria.

    • Desliza la puerta de la memoria fuera del compartimiento de la memoria.

  3. : paso 3, imagen 1 de 1
    • Retira el largo tornillo negro Phillips que esta a lado de la tarjeta de memoria.

    • Retira el pequeño EMI finger debajo del tornillo negro.

  4. Este paso está sin traducir. Ayuda a traducirlo

    : paso 4, imagen 1 de 1
    • Flip down the door on the right side of the battery compartment.

  5. Este paso está sin traducir. Ayuda a traducirlo

    : paso 5, imagen 1 de 1
    • Use a spudger or flathead screwdriver to disconnect the Airport antenna from the card.

  6. Este paso está sin traducir. Ayuda a traducirlo

    : paso 6, imagen 1 de 1
    • Grasp the plastic tab and pull the card out all the way.

  7. , Teclado: paso 7, imagen 1 de 1
    • En el teclado retira las teclas F1, F2, F11 y F12.

    • Esto es peligroso - respira profunda antes de continuar. Coloca tu dedo índice debajo de la esquina superior izquierda de la teclado y levántala hasta que oigas un click. Después mueve tu dedo al borde izquierdo de la tecla y levántalo para sacar la tecla.

    • Estas liberando las dos pestañas en el lado izquierdo de la tecla de dos pequeños agujeros en el mecanismo de tijeras de plástico.

    • Cuando reemplaces las teclas en el teclado, coloca la tecla directamente sobre el slot donde irá y presiona hacia abajo hasta que oigas que la tecla entra en su lugar.

  8. : paso 8, imagen 1 de 1
    • Usa tu uña o la pequeña cabeza plana de un desarmador para despegar los stickers grises que cubren cada tornillo.

  9. : paso 9, imagen 1 de 1
    • Retira los dos tornillos Phillips pequeños.

  10. : paso 10, imagen 1 de 1
    • Levanta el teclado por las teclas 'esc' y'eject' y levántalo con cuidado hasta que este vertical.

  11. : paso 11, imagen 1 de 1
    • Toma el conector plano del teclado cerca del conector y desconéctalo de la tarjeta lógica.

  12. Este paso está sin traducir. Ayuda a traducirlo

    : paso 12, imagen 1 de 1
    • Remove the three 2.5mm Phillips screws from within the battery compartment.

  13. Este paso está sin traducir. Ayuda a traducirlo

    : paso 13, imagen 1 de 1
    • Turn the computer 90 degrees clockwise and remove the two Phillips screws from the casing.

    • Outside case screws are aprox. 1/4 in long

  14. Este paso está sin traducir. Ayuda a traducirlo

    : paso 14, imagen 1 de 1
    • Turn the computer 90 degrees clockwise again, and remove only the bottom screw on either side of the hinge.

  15. Este paso está sin traducir. Ayuda a traducirlo

    : paso 15, imagen 1 de 1
    • Turn the computer 90 degrees clockwise just one more time, and remove the two Phillips screws on the exterior wall of the battery compartment.

    • Note: For reassembly the two screws have long necks.

  16. Este paso está sin traducir. Ayuda a traducirlo

    : paso 16, imagen 1 de 1
    • Turn the computer over and open it up.

    • Remove the following 14 screws:

    • Six 2.5 mm Phillips on either side of the keyboard area.

    • Five 4.5 mm Phillips on the left half of the keyboard area.

    • One 7 mm hex in the upper left corner of the upper case (a T6 Torx driver will do the job nicely).

    • One 15 mm Phillips in the upper middle of the keyboard area.

    • One 16.5 mm hex in the upper right of the upper case (again, a T6 Torx driver will work well).

  17. Este paso está sin traducir. Ayuda a traducirlo

    : paso 17, imagen 1 de 1
    • This step is extremely tricky, and has the potential to ruin your computer. It is easy to pull the plug with the red and black leads (the power) out of the motherboard. If you do that, it is nearly impossible to fix.

    • Peel up the two pieces of foil tape on the left side of the keyboard area.

    • The connectors at the ends of the cables are attached very firmly to the sockets on the logic board. Pulling directly on the cable will either separate the cable from its connector or the socket from the logic board.

    • Carefully disconnect the microphone and power cables from the logic board. Using your fingernails or a dental pick, carefully pry the connectors from their sockets. Make sure you're pulling only on the connector and not on the socket.

  18. Este paso está sin traducir. Ayuda a traducirlo

    : paso 18, imagen 1 de 1
    • Starting at one of the upper corners near the screen, work around the frame, separating the upper case from the lower case.

  19. Este paso está sin traducir. Ayuda a traducirlo

    : paso 19, imagen 1 de 1
    • Using a screw driver, gently release the two grey plastic clips inside the battery compartment in order to remove the right part of the upper case.

    • There are two more grey plastic clips holding the left part of the upper case. They are not easy to release as they are hidden from view prior to disassembly. They are in the same position as the two in the battery compartment, but on the opposite side of the trackpad. Try to stick a flat pry tool into the clip holes and push the clips inward (toward to screen) so they disengage and release the left part of the upper case.

    • Lift the upper case off the computer.

  20. Este paso está sin traducir. Ayuda a traducirlo

    : paso 20, imagen 1 de 1
    • Peel back the yellow tape securing the inverter cable near the fan.

  21. Este paso está sin traducir. Ayuda a traducirlo

    : paso 21, imagen 1 de 1
    • Remove the following eight screws:

    • One 4.5 mm Phillips near the modem.

    • Three 6 mm Phillips near the display.

    • Two large 7.5 mm Phillips with attached springs.

    • Two 13 mm Phillips, one on the lower left side of the heat sink and one between the fan and the optical drive.

  22. Este paso está sin traducir. Ayuda a traducirlo

    : paso 22, imagen 1 de 1
    • Peel up the Bluetooth cable on the right side of the fan.

  23. Este paso está sin traducir. Ayuda a traducirlo

    : paso 23, imagen 1 de 1
    • Lift up the inverter cable with one hand, and carefully thread it around the heat sink. The inverter cable is still attached to the logic board, so be careful not to put too much strain on the cable.

  24. Este paso está sin traducir. Ayuda a traducirlo

    : paso 24, imagen 1 de 1
    • Support the heat sink with both hands, and carefully lift it out of the computer. Be careful not to bend the copper heat pipe connecting the two sections of the heat sink.

    • If you need to mount the heat sink back into the laptop, we have a thermal paste guide that makes replacing the thermal compound easy.

  25. Este paso está sin traducir. Ayuda a traducirlo

    : paso 25, imagen 1 de 1
    • Remove the single Phillips screw securing the hall effect sensor board to the optical drive.

  26. Este paso está sin traducir. Ayuda a traducirlo

    : paso 26, imagen 1 de 1
    • Deroute the cable connecting the hall effect sensor board to the DC-to-DC board.

  27. Este paso está sin traducir. Ayuda a traducirlo

    : paso 27, imagen 1 de 1
    • Use a spudger or the tip of your finger to disconnect the hall effect sensor cable from the DC-to-DC board.

  28. Este paso está sin traducir. Ayuda a traducirlo

    : paso 28, imagen 1 de 1
    • Use the orange plastic loop to disconnect the hard drive cable from the logic board.

  29. Este paso está sin traducir. Ayuda a traducirlo

    : paso 29, imagen 1 de 1
    • Remove the two Phillips screws securing the hard drive bracket to the metal framework.

  30. Este paso está sin traducir. Ayuda a traducirlo

    : paso 30, imagen 1 de 1
    • Lift the hard drive up and out of the computer.

  31. Este paso está sin traducir. Ayuda a traducirlo

    : paso 31, imagen 1 de 1
    • Use a spudger or the tip of your finger to disconnect the sleep light cable from the DC-to-DC board.

  32. Este paso está sin traducir. Ayuda a traducirlo

    : paso 32, imagen 1 de 1
    • Remove the following five secrews/standoffs from the DC-to-DC board:

    • One 3.5 mm Phillips in the lower right corner.

    • Two 3 mm Phillips on either side of the battery contacts.

    • One 10 mm Phillips in the upper right corner.

    • One 14 mm long 4 mm standoff in the upper left corner. You can remove this standoff either with a 4 mm nut driver or needlenose pliers.

  33. Este paso está sin traducir. Ayuda a traducirlo

    : paso 33, imagen 1 de 1
    • Remove the silver EMI fingers located near the battery contacts.

  34. Este paso está sin traducir. Ayuda a traducirlo

    : paso 34, imagen 1 de 1
    • Use a spudger to pry up the end of the DC-to-DC board closest to the display and remove the board from the computer.

  35. Este paso está sin traducir. Ayuda a traducirlo

    : paso 35, imagen 1 de 1
    • Remove the three Phillips screws securing the modem and modem shield to the logic board.

  36. Este paso está sin traducir. Ayuda a traducirlo

    : paso 36, imagen 1 de 1
    • Disconnect the modem from the logic board by lifting the bottom edge of the modem. Don't remove the modem entirely just yet as it is still connected to the RJ-11 board.

  37. Este paso está sin traducir. Ayuda a traducirlo

    : paso 37, imagen 1 de 1
    • Turn the modem over and disconnect the RJ-11 cable.

  38. Este paso está sin traducir. Ayuda a traducirlo

    : paso 38, imagen 1 de 1
    • The connectors at the ends of the cables are often attached very firmly to the sockets on the logic board. Pulling directly on the cable will either separate the cable from its connector or the socket from the logic board.

    • Carefully disconnect six indicated connectors from the logic board. To disconnect the four white connectors, use your fingernails or a dental pick to carefully pry the connectors from their sockets. Make sure you're pulling only on the connector and not on the socket.

  39. Este paso está sin traducir. Ayuda a traducirlo

    : paso 39, imagen 1 de 1
    • Lift up middle speaker cable from the lower left corner of the fan, and disconnect the two sections of the cable.

  40. Este paso está sin traducir. Ayuda a traducirlo

    : paso 40, imagen 1 de 1
    • Deroute the microphone cable from its channel in the metal framework.

  41. Este paso está sin traducir. Ayuda a traducirlo

    : paso 41, imagen 1 de 1
    • Remove the following nine screws:

    • Four 3 mm Phillips allong the left edge and near the fan.

    • One 4 mm Phillips in the bottom left corner.

    • Two 6 mm Phillips near the left hinge.

    • One 9 mm Phillips in the top left corner of the fan.

    • One 12 mm Phillips just above where the hard drive was located.

  42. Este paso está sin traducir. Ayuda a traducirlo

    : paso 42, imagen 1 de 1
    • Peel up the yellow tape securing the display data cable to the metal framework, and deroute the display data cable from its slot in the framework.

  43. Este paso está sin traducir. Ayuda a traducirlo

    : paso 43, imagen 1 de 1
    • Remove the newly revealed Phillips screw near the RJ-11 board.

    • Some computers may have two Phillips screws securing the RJ-11 board to the metal framework.

  44. Este paso está sin traducir. Ayuda a traducirlo

    : paso 44, imagen 1 de 1
    • Lift the RJ-11 board up from the left side, and remove the single Phillips screw hidden beneath.

    • You may have to remove the metal shield above the RJ-11 board before you can lift it up.

  45. Este paso está sin traducir. Ayuda a traducirlo

    : paso 45, imagen 1 de 1
    • Lift up and remove the silver EMI fingers located above the ports on the left side of the computer.

  46. Este paso está sin traducir. Ayuda a traducirlo

    : paso 46, imagen 1 de 1
    • Pull back on the orange optical drive cable with one hand, and use your other hand to lift the front section of the metal framework over the optical drive cable.

  47. Este paso está sin traducir. Ayuda a traducirlo

    : paso 47, imagen 1 de 1
    • Deroute the microphone cable from its channel in the upper right corner of the framework.

    • The metal framework should now be free can be removed from the computer. Be careful when removing the metal framework that none of the cables get caught on the framework.

    • When reassembling the laptop, make sure that two wires come through the loop of metal on the frame on the upper right-hand side - a silver wire at right angles and the skinny black microphone channel. The third wire from underneath the frame is routed over the fan. The fourth wire from this corner is directly attached to the frame.

  48. Este paso está sin traducir. Ayuda a traducirlo

    : paso 48, imagen 1 de 1
    • Remove the two Phillips screws from the bottom right of the logic board.

    • When reassembling, take note of the plastic piece immediately to the right of the screws. Make sure you do not neglect to put it in place before screwing down the logic board.

  49. Este paso está sin traducir. Ayuda a traducirlo

    : paso 49, imagen 1 de 1
    • Do not lift the logic board out completely without first disconnecting the DC-In connector underneath the logic board.

    • Lift the logic board partly up from the optical side.

  50. Este paso está sin traducir. Ayuda a traducirlo

    : paso 50, imagen 1 de 1
    • Disconnect the DC-In connector from the underside of the logic board.

  51. Este paso está sin traducir. Ayuda a traducirlo

    : paso 51, imagen 1 de 1
    • Remove the two 6mm Phillips screws from the upper right corner of the computer.

    • Remove the newly-liberated small metal bracket.

  52. Este paso está sin traducir. Ayuda a traducirlo

    : paso 52, imagen 1 de 1
    • Remove the two recessed Phillips screws on the right side of the optical drive.

  53. Este paso está sin traducir. Ayuda a traducirlo

    : paso 53, imagen 1 de 1
    • Lift the optical drive up by its front left corner and pull it out of the computer.

    • If you have a CD or any other object jammed in your optical drive, we have an optical drive repair guide.

  54. Este paso está sin traducir. Ayuda a traducirlo

    : paso 54, imagen 1 de 1
    • Disconnect the multicolor connector by sliding it to the left.

  55. Este paso está sin traducir. Ayuda a traducirlo

    : paso 55, imagen 1 de 1
    • Disconnect the silver bluetooth cable by pulling directly up.

  56. Este paso está sin traducir. Ayuda a traducirlo

    : paso 56, imagen 1 de 1
    • Remove the single Phillips screw from the right side of the board.

    • Lift the bluetooth board out of the computer.

  57. Este paso está sin traducir. Ayuda a traducirlo

    : paso 57, imagen 1 de 1
    • Peel back the yellow tape from the right side of the subwoofer.

    • Remove the single Phillips screw from the right side of the subwoofer, under the tape you just removed.

    • Remove the yellow tape that secures the remaining cables to the side of the subwoofer.

  58. Este paso está sin traducir. Ayuda a traducirlo

    : paso 58, imagen 1 de 1
    • Slide the subwoofer away from the screen and out of the computer.

    • The subwoofer is adhered to the case, so a little force may be required.

  59. Este paso está sin traducir. Ayuda a traducirlo

    : paso 59, imagen 1 de 1
    • Deroute the Airport Extreme antenna from the card slot and lower case, removing tape as necessary.

  60. Este paso está sin traducir. Ayuda a traducirlo

    : paso 60, imagen 1 de 1
    • Place a cloth between the screen and the bottom case.

    • Close the bottom case and turn the laptop over.

    • Remove the two Phillips screws from the bottom case.

  61. Este paso está sin traducir. Ayuda a traducirlo

    : paso 61, imagen 1 de 1
    • Remove the two Phillips screws from either side of the display hinge.

  62. Este paso está sin traducir. Ayuda a traducirlo

    : paso 62, imagen 1 de 1
    • Grasp the lower case and push down on the hinge side while rotating the other end of the case toward you until it pops free, then remove it entirely (leaving the display).

    • You have effectively removed the computer from the display.

Linea de Meta

13 personas más completaron esta guía.

Documentos Adjuntos

iRobot

Miembro Desde 09/24/09

1 Reputación

636 Guías creadas

Un comentario

I want to use this monitor as a separate monitor for a MacMini early 2006 What driver circuit board kit should I use? can you let me know so I can buy one?

Michael Inman - Contestar

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 1

Ultimos 7 días: 7

Ultimos 30 días: 14

Todo El Tiempo: 22,971