Saltar al contenido principal
  1. Este paso está sin traducir. Ayuda a traducirlo

    Remove both expansion bay modules using the levers on the front of the computer.
    • Remove both expansion bay modules using the levers on the front of the computer.

    • Insert your index fingers inside the expansion bays and search for the two ribbed tabs on the underside of the upper case. The tabs are located near the bottom corners of the keyboard.

    • Pull the tabs toward yourself and the keyboard will pop up.

  2. Este paso está sin traducir. Ayuda a traducirlo

    Pull the keyboard forward to disengage the tabs holding it in back and rotate it toward you.
    • Pull the keyboard forward to disengage the tabs holding it in back and rotate it toward you.

    • Rest the keyboard on the trackpad.

  3. Este paso está sin traducir. Ayuda a traducirlo

    • This is a diagram of the ribbon clamp connectors you will disconnect in the next step.

    • 1) With your fingernails, grasp the locking bar on either side and pull up a small amount (about 1/16" or 2 mm).

    • 2) After disengaging the locking bar, slide the cable out of the connector.

  4. Este paso está sin traducir. Ayuda a traducirlo

    Disconnect the two keyboard connectors by disengaging the clamps and pulling the ribbons directly upward.
    • Disconnect the two keyboard connectors by disengaging the clamps and pulling the ribbons directly upward.

  5. Este paso está sin traducir. Ayuda a traducirlo

    Slide a spudger downward between each plastic strain relief cable and the wall of the case in order to bow out the cable beyond the small tab holding it in place.
    • Slide a spudger downward between each plastic strain relief cable and the wall of the case in order to bow out the cable beyond the small tab holding it in place.

    • Once the strain relief cables are free, lift the keyboard off.

  6. Este paso está sin traducir. Ayuda a traducirlo

    Your laptop should look approximately like this.
    • Your laptop should look approximately like this.

  7. Este paso está sin traducir. Ayuda a traducirlo

    Remove the two Phillips screws from the heat shield.
    • Remove the two Phillips screws from the heat shield.

    • One screw is shorter than the other. When putting the Wallstreet back together, this screw goes in the middle of the heat shield.

  8. Este paso está sin traducir. Ayuda a traducirlo

    Grasp the metal handle on the heat shield and pull up and toward yourself.
    • Grasp the metal handle on the heat shield and pull up and toward yourself.

  9. Este paso está sin traducir. Ayuda a traducirlo

    Unscrew, but do not remove, the single Phillips screw from the hard drive bracket.
    • Unscrew, but do not remove, the single Phillips screw from the hard drive bracket.

  10. Este paso está sin traducir. Ayuda a traducirlo

    Grasp the hard drive bracket on the left side and pull up and to the left.
    • Grasp the hard drive bracket on the left side and pull up and to the left.

  11. Este paso está sin traducir. Ayuda a traducirlo

    Your laptop should look approximately like this.
    • Your laptop should look approximately like this.

  12. Este paso está sin traducir. Ayuda a traducirlo

    Use a spudger, the tips of your fingers, or a flat non-metal tool to pry up the processor's right side.
    • Use a spudger, the tips of your fingers, or a flat non-metal tool to pry up the processor's right side.

    • Remove the processor by sliding it up and to the right.

    • The processor and RAM can be removed as a unit. It is not necessary to remove the RAM from the processor.

    • There are two tabs on the left side of the processor that fit into slots on the metal framework. Make sure these tabs are in the slots.

  13. Este paso está sin traducir. Ayuda a traducirlo

    Remove the single Phillips screw from the modem.
    • Remove the single Phillips screw from the modem.

    • Disconnect the orange PMU cable by pulling it directly up.

  14. Este paso está sin traducir. Ayuda a traducirlo

    Disconnect the modem from the logic board by lifting up on the right side using a spudger, the tip of your finger, or a flat non-metal tool.
    • Disconnect the modem from the logic board by lifting up on the right side using a spudger, the tip of your finger, or a flat non-metal tool.

    • Remove the modem by sliding it up and to the right.

  15. Este paso está sin traducir. Ayuda a traducirlo

    Your laptop should look approximately like this.
    • Your laptop should look approximately like this.

Linea de Meta

2 personas más completaron esta guía.

Documentos Adjuntos

iRobot

Miembro Desde 24/09/09

1 Reputación

647 Guías creadas

0 comentarios

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 0

Ultimos 7 días: 2

Ultimos 30 días: 7

Todo El Tiempo: 3,041