Introducción
Sigue esta guía para reemplazar la placa base de tu Sony Playstation 4.
La placa madre y la unidad óptica están emparejadas, por lo que si se reemplaza sólo la placa madre se obtendrá un dispositivo que no funciona. Asegúrese de pedir el emparejamiento correcto de la unidad óptica y la placa madre para su modelo PS4 y reemplace ambos.
Desenchufa tu PS4 antes de comenzar cualquier reparación.
Qué necesitas
-
-
Agarra la PS4 con ambas manos a lo largo del hueco en la cubierta superior.
-
Empuja el lado brillante de la cubierta superior con los pulgares hasta que salte a un lado.
-
Levanta la cubierta superior brillante hacia arriba y hacia atrás para quitarla del PS4.
-
-
-
Usa un destornillador Phillips para quitar el tornillo de 6.5 mm que fija el disco duro a la carcasa.
-
-
-
Usa pinzas para quitar las dos pegatinas en el centro de la parte trasera de la PS4 exponiendo dos tornillos de la caja.
-
-
-
Usa pinzas para quitar con cuidado las cubiertas de plástico de los tornillos en cada esquina, exponiendo dos tornillos más de la caja.
-
-
-
Quita los cuatro tornillos de seguridad Torx de 7.2 mm de la parte trasera de la PS4.
-
-
-
Usa tus pulgares para levantar la carcasa inferior y sacarla de la PS4.
-
-
-
Remueve tres tornillos de seguridad Torx de 9.7 mm.
-
Remueve dos tornillos Philips de 41mm y quita los seguros.
-
-
-
-
Usa la punta de un spudger para desconectar el cable de antena de la placa madre.
-
-
-
Usa tu uña para presionar la palanca metálica de liberación del cable plano en la parte superior de la unidad óptica.
-
Usa tus dedos o un par de pinzas para desconectar el cable de cinta tirando de la lengüeta negra.
-
-
-
Remueve los cuatro tornillos que sujetan el disco óptico.
-
Tres tornillos Torx de 9.7 mm
-
Un tornillo Phillips de 6.2 mm
-
-
-
Remueve los dos tornillos Torx de 9.7 mm que sujetan la caja superior.
-
-
-
Levanta la caja superior y vuelve a quitarla de la PS4.
“Significant force” is a bit of an understatement. It’s like it’s superglued together..
You absolutely should not need a lot of force for this. In the picture above, press upward using the left thumb from under the outer lip of the cover. You may need to pull it slightly toward you as well. Once that half is lifted, the right-hand side is still firmly attached. Keeping the left-hand side of the top separated, flip the unit over. Along the right-hand side, press the outside lip with your thumb about 2 thumb-widths down from the corner. There is a tab here and once released, the cover comes off easily and off in the back. Otherwise, you’ll be placing stress vertically (and rotationally) on the first tab on the side.
I appreciate this feedback – thank you. This sounds like a safer method. I’ll test it on our guide unit and update the procedure.
THIS SET OF INSTRUCTIONS FROM YOU, IS ABSOLUTELY SENSATIONAL.
I got this cover off quite easily. Still some resistance, but I didn't need this significant force at all.
THANK YOU!!
:)
Cary B -
I found an easier method for myself is to have the console upright and pointed away from myself. From this position, wrap your fingers over the top of the cover, hooking it in its front with the last digits of each finger. This allows you to press with your palm into the top of the console and pry in an upward/outward motion. This feels safer as it took much less force to disengage the problematic clip.
-
-
-
Remueve los doce tornillos Torx de 9.7 mm que sujetan el escudo EMI superior.
In my PS4, there is a small black Philips screw behind where the power lead connects to the motherboard. That screw connects the EMI shield to the inner metal where the power supply sits.
I had exactly the same thing, and mine is a fairly old model of PS4. Confused me for a moment until I spotted it.
Tom G -
Can confirm this.
This screw was on mine. To anyone reading this, flip the PS4 over and look where the pain in the ass power supply connector is.
Black screw right there.
If you have that screw of course. :)
Cary B -
-
-
-
Retira los dos tornillos Phillips de 15.6 mm.
-
Desenrosca gradualmente la placa de presión girando cada tornillo media vuelta a la vez.
-
Alterna entre los dos tornillos para mantener una presión uniforme en la placa de presión.
My PS4 also has 2 metal rings around each screw hole and 4 metal pieces 2 on each side closing in the same shape as the pressure plate as you take the pressure plate off?
How strong do you tighten the screws when re-applying the plate?
To the max, or stop one to two turns before?
I've tightened mine until the screws became taut and I've not had any stability issues.
hazelrat -
-
-
-
Remueve el escudo superior EMI.
This is the 2nd PS4 I have disassembled and on both units I have found there is a black Phillips screw securing the upper EMI shield. This should be mentioned in the teardown as the EMI shield cannot be removed completely without first removing this screw and you risk damaging the EMI shield in the process . To locate the screw turn the unit over and you will see a small black Phillips screw located near the power supply prongs. There will be a set of arrows pointing to the screw. Once you remove this screw then you can fully release the upper EMI shield.
Ditto. This is my first time disassembling a PS4. EMI shield didn’t lift off easily on one corner. Noticed the black Phillips screw holding it in place. I scrolled up in the tutorial to see if I missed it. Easy enough.
throw it way, electromagnetic fields dont exist
-
-
-
Inserta el extremo plano de un spudger entre el cable del ventilador y la placa madre.
-
Gira el spudger para levantar el conector y desconectarlo de la placa madre.
-
-
-
Levanta la placa madre de la PS4.
That shiny metal cover box on the opposite side of the hdi port shown in picture 30 at the very front is showing over heating signs I guess very brown around the edges I think is causing my PS4 not to show up on tv any ideas how to fix that hdi port looks fairly good to me but the black plastic port shows burnt signs as well that's on the same side of the HDMI port but the shiny metal cover is on the opposite side
-
Para volver a armar el dispositivo, siga estas instrucciones en orden inverso.
Lleva tus desechos electrónicos a un centro de reciclaje certificado.
¿La reparación no salió como planificaste? Consulta nuestra comunidad de respuestas
Compara tu parte de reemplazo con la parte original. Puede que tengas que transferir los componentes restantes o remover respaldos adhesivos de la parte nueva antes de instalarla.
Para volver a armar el dispositivo, siga estas instrucciones en orden inverso.
Lleva tus desechos electrónicos a un centro de reciclaje certificado.
¿La reparación no salió como planificaste? Consulta nuestra comunidad de respuestas
Compara tu parte de reemplazo con la parte original. Puede que tengas que transferir los componentes restantes o remover respaldos adhesivos de la parte nueva antes de instalarla.
Cancelar: No complete esta guía.
195 personas más completaron esta guía.
Un agradecimiento especial a estos traductores:
100%
Estos traductores nos están ayudando a reparar el mundo! ¿Quieres contribuir?
Empezar a traducir ›
17 comentarios
Regarding the three wire plug in step 20 - is there a good way to repair this piece if, say, you pulled the wires out of the connector by accident? is there a place to get a replacement part?
I have tried to replace the hdmi port however being somewhat of an idiot I slipped and knocked off onto the little black squares just behind the port on the left hand side. Does anyone know what these are?
contacts of the motherboard
You may be talking about capacitors that are critically important for the unit to function.
South30 -
You mean that little brown parts next to the desoldered HDMI port chip? Seems to be capaciators.
Check it with a multimeter: No connection through that parts: Capaciator, Connection through that parts: Coil
Ok so I was taking mine apart, and while I was separating the ribbon wire from the optical drive during step 7, I broke the top off the connector by accident. I thought I could fix it with hot glue, but my ps4 doesn't read disks (at all, doesn't even know there's a disk in the drive). Is there a way to repair this without getting a new drive?
when I bought the replacement motherboard and optical drive and installed everything, I got a message saying connect USB with software update. Is this because I'm using my original hdd from my original mobo+ optical drive that is different from the hdd my replacement parts came with?
Could you please tell me where you bought a replacement motherboard from as i've been looking everywhere!?
I’ve read along the guides that a BDP-020 optical drive can work with an SAA-001 motherboard, but mine still receives the CE-35888-2 error. Am I replacing the incorrect part?
Hi my ps4 has stopped working and doesnt turn on at all, ive tried different outlets and different power cables for the ps4, still no luck. Ive pulled it apart and had a look at the power supply board and mother board aswell as dusted it all out. The mother board has yellow stains/ dots near the hdmi port and some other random spots around the mother board. I have the first ps4.
Does anyone know whats wrong? Id rather fix it than pay for a new one.
Hi all, I am facing this CE-34878-0 error on all games. Reinstalled the software, replaced the HDD and reinstalled latest software but this error is keep coming. What is the solution.
Just wondering, can a ps4 work without an optical drive, like being all digital?
I am looking to replace the motherboard on my PS4. It’s had an HDMI replacement before, worked fine, but after I replaced the thermal paste it powers on but I don’t get any picture. The HDMI port seems fine all the pins seem ok. I was think of just replacing the whole motherboard all together any advice? Are PS4 motherboards swappable?
Excelente 😃