Repara tus cosas

Derecho a reparar

Tienda

PlayStation 3 Slim Laser lens Replacement

Escrito Por: ZFix (y 3 de otros participantes)
  • Comentarios: 13
  • Favoritos: 18
  • Terminaciones: 16

Dificultad

Moderar

Pasos

6

Tiempo Requerido

45 minutos

Secciones

1

Banderas

1

Member-Contributed Guide

Guía Contribuida Por Miembros

Un miembro increíble de nuestra comunidad escribió esta guía. No está supervisada por el personal de iFixit.

Introducción

Video tutorial - how to replace Laser Lens only:

Resumen del Video

  1. If present, remove the pieces of tape securing the cables to the body of the Blu-ray drive. If present, remove the pieces of tape securing the cables to the body of the Blu-ray drive.

    • If present, remove the pieces of tape securing the cables to the body of the Blu-ray drive.

    Editar

  2. Use the flat end of a spudger or your fingernail to flip up the retaining flap on the Blu-ray ribbon cable socket.

    • Use the flat end of a spudger or your fingernail to flip up the retaining flap on the Blu-ray ribbon cable socket.

    • Be sure you are prying up on the movable retaining flap, not the socket itself.

    Editar

  3. SALTEA LA ACTUALIZACIÓN

    Ahorra reparando con un kit todo en uno.

    Compra Kits de Reparación

    SALTEA LA ACTUALIZACIÓN

    Ahorra reparando con un kit todo en uno.

    Compra Kits de Reparación

  4. Pull the Blu-ray ribbon cable straight up and out of its socket.

    • Pull the Blu-ray ribbon cable straight up and out of its socket.

    Editar

  5. Pull the Blu-ray power cable straight up to lift its connector out of the socket on the Blu-ray drive.

    • Pull the Blu-ray power cable straight up to lift its connector out of the socket on the Blu-ray drive.

    Editar

  6. Remove the single 9.5 mm Phillips screw securing the Blu-ray drive to the lower case.

    • Remove the single 9.5 mm Phillips screw securing the Blu-ray drive to the lower case.

    Editar

  7. Lift the Blu-ray drive slightly by its right edge to dislodge the control board from its housing. Remove the Blu-ray drive from the PS3.

    • Lift the Blu-ray drive slightly by its right edge to dislodge the control board from its housing.

    • Remove the Blu-ray drive from the PS3.

    • After you reinstall the Blu-ray drive, be sure the control board is firmly seated in the lower case before proceeding.

    • If replacing the Blu-ray drive with a new drive, swap the circuit board from your old drive into the new drive.

    Editar
Conclusión

To reassemble your device, follow these instructions in reverse order.

16 personas más completaron esta guía.

Autor

con 3 otros colaboradores

ZFix

Miembro Desde 09/12/13

173,916 Reputación

309 Guías creadas

Insignias: 35

+ 32 más insignias

Equipo

Master Techs Miembro de Master Techs

Community

294 Miembros

953 Guías creadas

5 comentarios

Agregar un comentario

Donde puedo comprar refacciones y partes para PS3 Slim?

David - Contestar

yo vendo amigo = ivaramso@gmail.com para ventas

Ivan Ramirez -

How can this be easy, but the Blu-Ray drive be considered Moderate? You need to complete the Blu-Ray drive removal prior to replacing the laser lens, which means this is at best a Moderate task.

Ben Kevan - Contestar

This is not lens replacement, this is drive replacement. Is there a separate guide for lens replacement?

cmchallam - Contestar

Shows how to do the laser assembly in the video but not how to reinstall it in the drive. Lazy guide. Just buy a whole new drive if you are following this guide.

Beninja - Contestar

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 1

Ultimos 7 días: 20

Ultimos 30 días: 87

Todo El Tiempo: 27,676