Introducción
Sustituye el conjunto del láser de tu unidad de disco óptica. Sustituir el láser requiere que tengas o compres un láser nuevo.
Qué necesitas
-
-
Utiliza la parte plana de una espátula metálica para hacer palanca y quitar las patas de goma que ocultan los tornillos.
-
Quita los siguientes ocho tornillos que aseguran la carcasa superior con la inferior.
-
Cuatro tornillos Phillips de 55.4 mm.
-
Cuatro tornillos Phillips de 18.0 mm.
-
-
-
Algunos modelos tienen un número diferentes de tornillos y patas de goma. Quita todos los que veas en la carcasa inferior.
-
El modelo que tiene 10 tornillos, tiene 6 en la parte inferior y 4 en la bandeja superior de la parte inferior. Échale un vistazo a la foto para que te quede más claro.
-
-
-
-
Levanta la carcasa superior de la carcasa inferior.
-
Con cuidado quita el cable de alimentación que une ambas mitades, para ello desconéctalo de la parte inferior de la carcasa.
If you have a 5000x model, then the power and reset buttons are attached to the console, not the lid. Therefore there won’t be a cord
-
-
-
Quita los cuatro tornillos Phillips de 6.4 mm que sujetan la tapa superior de la unidad de disco óptico.
-
Levanta y quita la tapa de la unidad de disco óptico.
-
-
-
Quita los dos tornillos Phillips de 7.2 mm de color negro que sujetan los raíles de color plateado que mantienen al láser en su sitio.
where can someone buy replacements for these in this day and age
eBay is a good place for it
Nicholas -
-
Para volver a montar tu PlayStation 2 sigue la guía en orden inverso, desde el final hacia arriba.
Para volver a montar tu PlayStation 2 sigue la guía en orden inverso, desde el final hacia arriba.
Cancelar: No complete esta guía.
34 personas más completaron esta guía.
Un agradecimiento especial a estos traductores:
100%
¡ MemoryOverflow nos está ayudando a reparar el mundo! ¿Quieres contribuir?
Empezar a traducir ›
8 comentarios
just did the laser replacement, however the playstation still identifies "no data" when game is inserted. it says "reading disk" for a few seconds then nothing else happens. thought?
Have you removed the security solder blob? All new Lenses have this somewhere in the circuitry.
I noticed that many times when you replace a lens it throws of the rotary motor. Some ps2 consoles have only 1 hex adjustment yet others have 2. If you have the covers off and just replaced the lenses you should always plug it back in w/ the top off still and adjust it until you see the disc spinning rapidly and laser is moving back and forth. Another way for calibrating is to remove said disc and if lens and ribbon move all the way forward and all the way back 3 or more times then you are almost done. At that point plug in tv chord and place in a disc if the PlayStation 2 logo comes on and disappears in less than 3 seconds carefully replace all parts and your good to go.
Could you please add the parts you would need to replace this to the parts portion.
Nice guide by the way.
My ps2 doesn't spin the cd what can i do to fix it
I have two PlayStation 2 SCPH-50003. Both used, don't have any mode chip on it! One of them play all game PlayStation/ PlayStation 2 black blue and silver discs.
The other played SSX 3 and Tomb raider legend but videos where slow and gameplay had problems. Just tested it and minutes later stoped working.
I Ibought2 lenses KHS-400C. I removed the solder spot from both of lenses. I tried both of them and none of them worked! I tried from the other working PlayStation 2 and didn't worked either! I tried all 4 KHS-400C on the working console and they all worked!
What else can cause Disc read error? Moreover I replaced the drive with motors and eject mechanism from the working one to the non working with no change!
Thx i have a problem with that's
Before proceeding to step 2, Take a look at your PS2, some PS2's have 10 screws (and screw covers) instead of 8 (i found them underneath the optical drive), these instructions have mislead me and i ended up breaking my top cover for my PS2.
Tristan - Contestar
Ich möchte daraufhin weisen, daß es bei der SCPH-50004 zwei verschiedene Schraubabdeckungen gibt.
4x Kreuzförmig 4x rechteckig
Sowie eine silberne schraube die sich an der unterseite aufhöhe des Reset-Knopfes befindet.
Christian Lehnhardt - Contestar