Saltar al contenido principal

Repara tus cosas

Derecho a reparar

Tienda

  1. Este paso está sin traducir. Ayuda a traducirlo

    Remove the foam body.
    • Remove the foam body.

  2. Este paso está sin traducir. Ayuda a traducirlo

    Disconnect the battery by pulling the two red wires apart. Remove the battery by releasing the battery retaining straps.
    • Disconnect the battery by pulling the two red wires apart.

    • Remove the battery by releasing the battery retaining straps.

  3. Este paso está sin traducir. Ayuda a traducirlo

    Turn the drone upside down. The cover is held on by plastic tape. Peel off the tape and use a spudger to remove the back cover.
    • Turn the drone upside down.

    • The cover is held on by plastic tape. Peel off the tape and use a spudger to remove the back cover.

  4. Este paso está sin traducir. Ayuda a traducirlo

    Using a spudger, separate the connector for the downward camera. Remove the camera from the body by pulling it off the foam body. Remove the camera from the body by pulling it off the foam body.
    • Using a spudger, separate the connector for the downward camera.

    • Remove the camera from the body by pulling it off the foam body.

  5. Este paso está sin traducir. Ayuda a traducirlo

    Use a spudger to release the black retaining clip. Then  disconnect the connector to the sensors. Use tweezers to carefully remove the ribbon from the connector.
    • Use a spudger to release the black retaining clip. Then disconnect the connector to the sensors.

    • Use tweezers to carefully remove the ribbon from the connector.

  6. Este paso está sin traducir. Ayuda a traducirlo

    Remove the four 8mm torx screws with a T6 bit.
    • Remove the four 8mm torx screws with a T6 bit.

    • Remove the four 8mm philips head screws with a PH00 bit.

  7. Este paso está sin traducir. Ayuda a traducirlo

    Carefully pull the secondary board from the mainboard. Carefully pull the secondary board from the mainboard.
    • Carefully pull the secondary board from the mainboard.

  8. Este paso está sin traducir. Ayuda a traducirlo

    Turn the drone right side up Remove the USB connector from the battery retaining straps. Remove the USB connector from the battery retaining straps.
    • Turn the drone right side up

    • Remove the USB connector from the battery retaining straps.

  9. Este paso está sin traducir. Ayuda a traducirlo

    Release the rubber clip holding the USB and battery power cable to the body.
    • Release the rubber clip holding the USB and battery power cable to the body.

  10. Este paso está sin traducir. Ayuda a traducirlo

    Avoid using sharp tools near the battery. Push the USB and power cable through the battery panel.
    • Avoid using sharp tools near the battery.

    • Push the USB and power cable through the battery panel.

  11. Este paso está sin traducir. Ayuda a traducirlo

    Turn the drone upside down again. Use a spudger to release the connector and carefully remove the ribbon.
    • Turn the drone upside down again.

    • Use a spudger to release the connector and carefully remove the ribbon.

  12. Este paso está sin traducir. Ayuda a traducirlo

    Lift the mainboard up so that you can access the back. Disconnect the first connector with the white wires using a nylon spudger.
    • Lift the mainboard up so that you can access the back.

    • Disconnect the first connector with the white wires using a nylon spudger.

    • Disconnect the second connector with the red and black wires using a spudger.

  13. Este paso está sin traducir. Ayuda a traducirlo

    The mainboard is now fully detached and can be removed.
    • The mainboard is now fully detached and can be removed.

  14. Este paso está sin traducir. Ayuda a traducirlo

    Using a nylon spudger, peel off the four pieces of plastic securing the frame to the body.
    • Using a nylon spudger, peel off the four pieces of plastic securing the frame to the body.

  15. Este paso está sin traducir. Ayuda a traducirlo

    Carefully maneuver the four arms of the drone’s central cross until it detaches from the body by pulling apart the foam surrounding the arms.
    • Carefully maneuver the four arms of the drone’s central cross until it detaches from the body by pulling apart the foam surrounding the arms.

  16. Este paso está sin traducir. Ayuda a traducirlo

    The central cross can now be removed and replaced.
    • The central cross can now be removed and replaced.

Linea de Meta

4 personas más completaron esta guía.

David Hoyt

Miembro Desde 09/04/10

3,846 Reputación

43 Guías creadas

Equipo

Cal Poly, Team 25-89, Amido Spring 2010 Miembro de Cal Poly, Team 25-89, Amido Spring 2010

CPSU-AMIDO-S10S25G89

4 Miembros

52 Guías creadas

If the crossbones are off just a bit would that effect the flight?

John Wurst - Contestar

So once I have removed the central cross, how do I put it all back together again?? I feel as though this is letting your guide down!!!!

Jacob Kenworthy - Contestar

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 0

Ultimos 7 días: 8

Ultimos 30 días: 39

Todo El Tiempo: 5,515