Saltar al contenido principal

Esta versión puede contener ediciones incorrectas. Cambiar a la última instantánea verificada.

Qué necesitas

  1. Este paso está sin traducir. Ayuda a traducirlo

    : paso 1, imagen 1 de 1
    • Locate the bay door for the battery on the left side of the laptop.

  2. Este paso está sin traducir. Ayuda a traducirlo

    : paso 2, imagen 1 de 2 : paso 2, imagen 2 de 2
    • Slide the latch to the right and then down to unlock it.

    • Pull out the battery.

  3. Este paso está sin traducir. Ayuda a traducirlo

    : paso 3, imagen 1 de 1
    • Remove the four hinge screws from the back of the computer.

  4. Este paso está sin traducir. Ayuda a traducirlo

    : paso 4, imagen 1 de 2 : paso 4, imagen 2 de 2
    • Open the laptop and remove the four indicated screws with a Phillips size 0 screwdriver.

    • Pry off the plastic strip which was previously held in place by the screws.

  5. Este paso está sin traducir. Ayuda a traducirlo

    : paso 5, imagen 1 de 1
    • Remove the four hinge screws to allow the hinges to rotate up and move.

  6. Este paso está sin traducir. Ayuda a traducirlo

    : paso 6, imagen 1 de 1
    • Remove 16 screws from the top of the closed laptop.

    • 12 Phillips size 1 screws

    • 2 Phillips size 0 screws

    • 2 Torx size 6 screws (T6)

  7. Este paso está sin traducir. Ayuda a traducirlo

    : paso 7, imagen 1 de 1
    • Gently break the adhesive seal between the front and rear display cases with a plastic opening tool.

    • You will need to reapply the silicon adhesive during reassembly to ensure watertight seal.

  8. Este paso está sin traducir. Ayuda a traducirlo

    : paso 8, imagen 1 de 1
    • Pull the top halve of the casing up revealing the inside of the screen

  9. Este paso está sin traducir. Ayuda a traducirlo

    : paso 9, imagen 1 de 2 : paso 9, imagen 2 de 2
    • The top half of the case can be removed by sliding the tabs out from under the hinges.

    • This makes unplugging the screen wiring much easier

  10. Este paso está sin traducir. Ayuda a traducirlo

    : paso 10, imagen 1 de 1
    • There are 4 wires that need to be unplugged to remove the screen.

  11. Este paso está sin traducir. Ayuda a traducirlo

    : paso 11, imagen 1 de 1
    • For the first wire, peel back the silver cover tape to reveal the connection.

  12. Este paso está sin traducir. Ayuda a traducirlo

    : paso 12, imagen 1 de 1
    • Pull the wiring away from the connection to release it.

  13. Este paso está sin traducir. Ayuda a traducirlo

    : paso 13, imagen 1 de 1
    • Remove the 3 strips of black tape as shown to reveal connections 2 and 3.

    • Pull the wiring for each away from the connections to remove.

  14. Este paso está sin traducir. Ayuda a traducirlo

    : paso 14, imagen 1 de 1
    • The 4th connection is already visible.

    • Depending on your model it might not be plugged into anything. If it is, remove it the same way the other 3 connections were removed.

  15. Este paso está sin traducir. Ayuda a traducirlo

    : paso 15, imagen 1 de 2 : paso 15, imagen 2 de 2
    • Using a plastic opening tool, lift the screen as shown from the case and pull free.

Linea de Meta

5 personas más completaron esta guía.

Dylan Bloom

Miembro Desde 04/12/10

373 Reputación

4 Guías creadas

Equipo

Cal Poly, Team 27-93, Amido Spring 2010 Miembro de Cal Poly, Team 27-93, Amido Spring 2010

CPSU-AMIDO-S10S27G93

4 Miembros

26 Guías creadas

Un comentario

This guide is good for replacing the LCD screen, but it is not complete for the touchscreen panel, which requires some more delicate and precise steps. I think the title of the guide needs to be changed.

Thanks

Alessandro Cervelli - Contestar

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 2

Ultimos 7 días: 5

Ultimos 30 días: 12

Todo El Tiempo: 17,078