Introducción

This guide will take you through the steps of removing the touchscreen.

  1. Locate the bay door for the battery on the left side of the laptop.
    • Locate the bay door for the battery on the left side of the laptop.

    Agregar Comentario

  2. Slide the latch to the right and then down to unlock it.
    • Slide the latch to the right and then down to unlock it.

    • Pull out the battery.

    Agregar Comentario

    • Remove the four hinge screws from the back of the computer.

    Agregar Comentario

    • Open the laptop and remove the four indicated screws with a Phillips size 0 screwdriver.

    • Pry off the plastic strip which was previously held in place by the screws.

    Agregar Comentario

    • Remove the four hinge screws to allow the hinges to rotate up and move.

    Agregar Comentario

  3. Reparte el espíritu de reparación esta Navidad
    Obtén $12 de descuento en tu compra de $50 o más con el código FIXMAS12
    Reparte el espíritu de reparación esta Navidad
    Obtén $12 de descuento en tu compra de $50 o más con el código FIXMAS12
    • Remove 16 screws from the top of the closed laptop.

      • 12 Phillips size 1 screws

      • 2 Phillips size 0 screws

      • 2 Torx size 6 screws (T6)

    I found that the Torx screw on my model to be T8.

    Harley - Contestar

    Is the touchscreen & the LCD 1 piece? or are they separate?

    Chasity Miller -

    • Gently break the adhesive seal between the front and rear display cases with a plastic opening tool.

      • You will need to reapply the silicon adhesive during reassembly to ensure watertight seal.

    Agregar Comentario

    • Pull the top halve of the casing up revealing the inside of the screen

    Agregar Comentario

    • The top half of the case can be removed by sliding the tabs out from under the hinges.

      • This makes unplugging the screen wiring much easier

    Agregar Comentario

    • There are 4 wires that need to be unplugged to remove the screen.

    Agregar Comentario

    • For the first wire, peel back the silver cover tape to reveal the connection.

    Agregar Comentario

    • Pull the wiring away from the connection to release it.

    Agregar Comentario

    • Remove the 3 strips of black tape as shown to reveal connections 2 and 3.

    • Pull the wiring for each away from the connections to remove.

    Agregar Comentario

    • The 4th connection is already visible.

      • Depending on your model it might not be plugged into anything. If it is, remove it the same way the other 3 connections were removed.

    Agregar Comentario

    • Using a plastic opening tool, lift the screen as shown from the case and pull free.

    Agregar Comentario

Conclusión

To reassemble your device, follow these instructions in reverse order.

5 personas más completaron esta guía.

Dylan Bloom

Miembro Desde 12/04/10

262 Reputación

4 Guías creadas

Equipo

Cal Poly, Team 27-93, Amido Spring 2010 Miembro de Cal Poly, Team 27-93, Amido Spring 2010

CPSU-AMIDO-S10S27G93

4 Miembros

12 Guías creadas

This guide is good for replacing the LCD screen, but it is not complete for the touchscreen panel, which requires some more delicate and precise steps. I think the title of the guide needs to be changed.

Thanks

Alessandro Cervelli - Contestar

Agregar Comentario

Ver Estadísticas:

Ultimas 24 Horas: 0

Últimos 7 Días: 10

Últimos 30 Días: 29

Todo El Tiempo: 15,433