Repara tus cosas Comunidad Tienda

Panasonic DMC-FZ70 Back Panel Replacement

Introducción

Prerequisite Only

This guide will show you how to remove the back panel of the camera so that you can access the inside.

Before you begin, make sure that the battery and SD card have been removed from the camera.

Qué necesitas

  1. Panasonic DMC-FZ70 Back Panel Replacement, Back Panel: paso 1, imagen 1 de 2 Panasonic DMC-FZ70 Back Panel Replacement, Back Panel: paso 1, imagen 2 de 2

    • All screws should be removed using a Phillips #0 screwdriver.

    • Using your screwdriver, unscrew the two 5.0 mm Philips screws to the right of the LCD screen.

    Editar

  2. Panasonic DMC-FZ70 Back Panel Replacement: paso 2, imagen 1 de 2 Panasonic DMC-FZ70 Back Panel Replacement: paso 2, imagen 2 de 2

    • Flip the camera over to the left side of the screen and unscrew the 5mm Phillips screw found there.

    Editar

  3. Panasonic DMC-FZ70 Back Panel Replacement: paso 3, imagen 1 de 2 Panasonic DMC-FZ70 Back Panel Replacement: paso 3, imagen 2 de 2

    • Turn the camera upside down and unscrew the three 5mm screws found on the bottom.

    Editar

  5. Panasonic DMC-FZ70 Back Panel Replacement: paso 4, imagen 1 de 2 Panasonic DMC-FZ70 Back Panel Replacement: paso 4, imagen 2 de 2

    • On the top of the camera locate the two rails with a thin sheet of metal on the floor between them.

    • With a metal spudger, lift this sheet and push it out of the rail device to detach it from the camera.

    Editar

  6. Panasonic DMC-FZ70 Back Panel Replacement: paso 5, imagen 1 de 1

    • Proceed to remove the four 5mm Phillips screws that you just uncovered.

    Editar

  7. Panasonic DMC-FZ70 Back Panel Replacement: paso 6, imagen 1 de 1

    • Slowly pull on both side of the camera, until both halves begin to separate from each other.

    • Do not pull too hard, as both halves are held together with ZIF connector cables.

    Editar

  8. Panasonic DMC-FZ70 Back Panel Replacement: paso 7, imagen 1 de 3 Panasonic DMC-FZ70 Back Panel Replacement: paso 7, imagen 2 de 3 Panasonic DMC-FZ70 Back Panel Replacement: paso 7, imagen 3 de 3

    • Using a plastic opening tool, carefully flip up the small black levers that attach the ribbon cables to the ZIF connectors on the motherboard.

    • Carefully pull the ribbon cables out of the slot once they have been released.

    • Only the two indicated connectors need to be removed to separate the two halves of the camera.

    Editar
Conclusión

To reassemble your device, follow these instructions in reverse order.

Autor

con 6 otros colaboradores

Alberto Rodriguez

Miembro Desde 01/24/17

531 Reputación

4 Guías creadas

Insignias: 13

+ 10 más insignias

Equipo

Cal Poly, Team 21-3, Maness Winter 2017 Miembro de Cal Poly, Team 21-3, Maness Winter 2017

CPSU-MANESS-W17S21G3

6 Miembros

12 Guías creadas

0 comentarios

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 1

Ultimos 7 días: 2

Ultimos 30 días: 3

Todo El Tiempo: 625