Saltar al contenido principal

Repara tus cosas

Derecho a reparar

Tienda

Introducción

This guide will show you how to access the front frame of the camera. This is the area of the camera that contains buttons like the playback and cursor buttons, as well as the window through which you can view the LCD screen. If these buttons have come loose, or if the frame is cracked, this guide will help you replace the frame. Before you begin, make sure that the battery and SD card have been removed.

  1. All screws should be removed using a Phillips #0 screwdriver. Using your screwdriver, unscrew the two 5.0 mm Philips screws to the right of the LCD screen.
    • All screws should be removed using a Phillips #0 screwdriver.

    • Using your screwdriver, unscrew the two 5.0 mm Philips screws to the right of the LCD screen.

  2. Flip the camera over to the left side of the screen and unscrew the 5mm Phillips screw found there. Flip the camera over to the left side of the screen and unscrew the 5mm Phillips screw found there.
    • Flip the camera over to the left side of the screen and unscrew the 5mm Phillips screw found there.

  3. Turn the camera upside down and  unscrew the three 5mm screws found on the bottom. Turn the camera upside down and  unscrew the three 5mm screws found on the bottom.
    • Turn the camera upside down and unscrew the three 5mm screws found on the bottom.

  4. On the top of the camera  locate the two rails with a thin sheet of metal on the floor between them. With a metal spudger, lift this sheet and push it out of the rail device to detach it from the camera.
    • On the top of the camera locate the two rails with a thin sheet of metal on the floor between them.

    • With a metal spudger, lift this sheet and push it out of the rail device to detach it from the camera.

  5. SALTEA LA ACTUALIZACIÓN

    Ahorra reparando con un kit todo en uno.

    Compra Kits de Reparación

    SALTEA LA ACTUALIZACIÓN

    Ahorra reparando con un kit todo en uno.

    Compra Kits de Reparación
  6. Proceed to remove the four 5mm Phillips screws that you just uncovered.
    • Proceed to remove the four 5mm Phillips screws that you just uncovered.

  7. Slowly pull on both side of the camera, until both halves begin to separate from each other.
    • Slowly pull on both side of the camera, until both halves begin to separate from each other.

    • Do not pull too hard, as both halves are held together with ZIF connector cables.

  8. Using a plastic opening tool, carefully flip up the small black levers that attach the ribbon cables to the ZIF connectors on the motherboard. Carefully pull the ribbon cables out of the slot once they have been released. Only the two indicated connectors need to be removed to separate the two halves of the camera.
    • Using a plastic opening tool, carefully flip up the small black levers that attach the ribbon cables to the ZIF connectors on the motherboard.

    • Carefully pull the ribbon cables out of the slot once they have been released.

    • Only the two indicated connectors need to be removed to separate the two halves of the camera.

  9. Unscrew the five 5mm screws on the panel that you just removed. Unscrew the five 5mm screws on the panel that you just removed.
    • Unscrew the five 5mm screws on the panel that you just removed.

  10. Remove the entire silver panel to reveal the back of the LCD screen Remove the entire silver panel to reveal the back of the LCD screen
    • Remove the entire silver panel to reveal the back of the LCD screen

  11. Remove the LCD screen.
    • Remove the LCD screen.

  12. You can now access the back panel and the buttons on it.
    • You can now access the back panel and the buttons on it.

  13. To remove a button, lightly press its front face and it should detach with ease.
    • To remove a button, lightly press its front face and it should detach with ease.

    • To put a button back into the camera, press on front its back face until it snaps back on.

Conclusión

To reassemble your device, follow these instructions in reverse order.

2 personas más completaron esta guía.

Emily Kuzmicky

Miembro Desde 24/01/17

363 Reputación

2 Guías creadas

Equipo

Cal Poly, Team 21-3, Maness Winter 2017 Miembro de Cal Poly, Team 21-3, Maness Winter 2017

CPSU-MANESS-W17S21G3

6 Miembros

12 Guías creadas

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 1

Ultimos 7 días: 2

Ultimos 30 días: 7

Todo El Tiempo: 453