Saltar al contenido principal

Introducción

This is a repair guide to access and replace the LCD screen.

  1. Palm Treo 650 LCD Screen Replacement, Battery and Stylus: paso 1, imagen 1 de 1
    • Position the phone so the screen faces down.

    • Remove the stylus found on the back of the phone.

  2. Palm Treo 650 LCD Screen Replacement: paso 2, imagen 1 de 1
    • To remove the battery cover, hold down the button in the middle of the phone's back.

    • Slide the cover down to remove it, and set the cover aside.

  3. Palm Treo 650 LCD Screen Replacement: paso 3, imagen 1 de 2 Palm Treo 650 LCD Screen Replacement: paso 3, imagen 2 de 2
    • Lift the edge of the battery, separating contact points, and pull out as pictured.

  4. Palm Treo 650 LCD Screen Replacement, Case: paso 4, imagen 1 de 1
    • Remove the round rubber cover on the back of the phone located immediately below the antenna.

    • This will uncover a screw that will be removed in the next step.

  5. Palm Treo 650 LCD Screen Replacement: paso 5, imagen 1 de 2 Palm Treo 650 LCD Screen Replacement: paso 5, imagen 2 de 2
    • Remove the six 6.9 mm screws as pictured with a T5 Torx screwdriver.

    • Remove the single 9.8 mm screw next to the antenna on the back plate using a Phillips #00 screwdriver.

  6. Palm Treo 650 LCD Screen Replacement: paso 6, imagen 1 de 1
    • Remove the antenna.

  7. Palm Treo 650 LCD Screen Replacement: paso 7, imagen 1 de 2 Palm Treo 650 LCD Screen Replacement: paso 7, imagen 2 de 2
    • Pry the back cover off using an iFixIt opening tool.

    • The back cover is attached by several small clips on the inside.

  8. Palm Treo 650 LCD Screen Replacement, Motherboard: paso 8, imagen 1 de 3 Palm Treo 650 LCD Screen Replacement, Motherboard: paso 8, imagen 2 de 3 Palm Treo 650 LCD Screen Replacement, Motherboard: paso 8, imagen 3 de 3
    • Disconnect the ribbon cable before removing the motherboard.

    • Unclip the gray tab.

    • Pull out the orange ribbon cable.

  9. Palm Treo 650 LCD Screen Replacement: paso 9, imagen 1 de 2 Palm Treo 650 LCD Screen Replacement: paso 9, imagen 2 de 2
    • Pull off the motherboard.

  10. Palm Treo 650 LCD Screen Replacement, LCD Screen: paso 10, imagen 1 de 3 Palm Treo 650 LCD Screen Replacement, LCD Screen: paso 10, imagen 2 de 3 Palm Treo 650 LCD Screen Replacement, LCD Screen: paso 10, imagen 3 de 3
    • Lift up the LCD screen so that the ribbon strip connecting it to the motherboard can be accessed.

    • Only lift the screen high enough to access the ribbon cable.

  11. Palm Treo 650 LCD Screen Replacement: paso 11, imagen 1 de 2 Palm Treo 650 LCD Screen Replacement: paso 11, imagen 2 de 2
    • Unclip the gray tab.

    • Pull out the orange ribbon strip.

    • Remove the LCD screen.

Conclusión

To reassemble your device, follow these instructions in reverse order.

3 personas más completaron esta guía.

cgood

Miembro Desde 28/10/09

122 Reputación

7 Guías creadas

Equipo

Cal Poly, Team 19-3, Maness Fall 2009 Miembro de Cal Poly, Team 19-3, Maness Fall 2009

CPSU-MANESS-F09S19G3

4 Miembros

18 Guías creadas

0 comentarios

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 0

Ultimos 7 días: 0

Ultimos 30 días: 14

Todo El Tiempo: 5,026