Repara tus cosas

Derecho a reparar

Tienda

Palm Treo 650 Keyboard Replacement

Escrito Por: cgood (y 7 de otros participantes)
  • Comentarios: 0
  • Favoritos: 2
  • Terminaciones: 2

Dificultad

Moderado

Pasos

12

Tiempo Requerido

10 minutos

Secciones

4

Banderas

4

Student In Progress

Estudiante en Progreso

Esta guía está siendo editada por alumnos diligentes.

Grammar Police

Policía gramatical

Acepta a tu profesor de inglés interior y ayuda a mejorar la gramática de esta guía!

Inconsistent Images

Imágenes Inconsistentes

Actualizando las imágenes de esta guía para que sean más consistente con los requisitos previos aumentaran su genialidad.

Incorrect Tools

Herramientas incorrectas

Ayuda a mejorar esta guía mejor usando las herramientas correctas en imágenes y/o texto.

Introducción

This guide will help you take apart, clean, and (if necessary) replace the palm treo keyboard.

  1. Position the phone so the screen faces down.

    • Position the phone so the screen faces down.

    • Remove the stylus found on the back of the phone.

    Editar

  2. To remove the battery cover, hold down the button in the middle of the phone's back.

    • To remove the battery cover, hold down the button in the middle of the phone's back.

    • Slide the cover down to remove. Set the cover aside.

    Editar

  3. Lift the edge of the battery, separating contact points, and pull out as pictured. Lift the edge of the battery, separating contact points, and pull out as pictured.

    • Lift the edge of the battery, separating contact points, and pull out as pictured.

    Editar

  4. Remove the small round rubber cover on the back of the phone located immediately below the antenna.

    • Remove the small round rubber cover on the back of the phone located immediately below the antenna.

    • This will uncover a screw that will be removed in the next step.

    Editar

  6. Unscrew the screws around the back plate with a T5 Torx Screwdriver. Six black 6.9 mm Torx screws

    • Unscrew the screws around the back plate with a T5 Torx Screwdriver.

    • Six black 6.9 mm Torx screws

    • Unscrew the screw next to the antennae on the back plate.

    • One 9.75 mm Phillips antenna screw with a Phillips #00 Screwdriver.

    Editar

  7. Remove the antennae.

    • Remove the antennae.

    Editar

  8. Pry the back cover off using a spudger or similar tool. The back cover is attached by several small clips on the inside.

    • Pry the back cover off using a spudger or similar tool.

    • The back cover is attached by several small clips on the inside.

    Editar

  9. Disconnect the ribbon cable before removing the motherboard. Unclip the gray tab. Pull out the orange ribbon cable.

    • Disconnect the ribbon cable before removing the motherboard.

    • Unclip the gray tab.

    • Pull out the orange ribbon cable.

    Editar

  10. Pull off the mother board. Install replacement or repaired motherboard, reversing steps above.

    • Pull off the mother board.

    • Install replacement or repaired motherboard, reversing steps above.

    Editar

  11. Unscrew the two 3.2 mm screws with a Phillips #00 screwdriver.

    • Unscrew the two 3.2 mm screws with a Phillips #00 screwdriver.

    Editar

  12. Pull off the circuit board.

    • Pull off the circuit board.

    Editar

  13. Remove the keypad for cleaning or replacing.

    • Remove the keypad for cleaning or replacing.

    Editar
Conclusión

To reassemble your device, follow these instructions in reverse order.

2 personas más completaron esta guía.

Autor

con 7 otros colaboradores

cgood

Miembro Desde 28/10/09

122 Reputación

7 Guías creadas

Insignias: 10

+ 7 más insignias

Equipo

Cal Poly, Team 19-3, Maness Fall 2009 Miembro de Cal Poly, Team 19-3, Maness Fall 2009

CPSU-MANESS-F09S19G3

4 Miembros

18 Guías creadas

0 comentarios

Agregar un comentario

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 0

Ultimos 7 días: 0

Ultimos 30 días: 3

Todo El Tiempo: 4,571