Introducción

Guide for removing the Analog stick in a Sony PSP-3000

Place the PSP face down and locate the battery cover on the left side of the device. Lift and remove the battery cover to reveal the battery. Remove the battery.
  • Place the PSP face down and locate the battery cover on the left side of the device.

  • Lift and remove the battery cover to reveal the battery.

  • Remove the battery.

Agregar Comentario

Peel back the warranty sticker that is behind the battery with a spudger or your fingernail.
  • Peel back the warranty sticker that is behind the battery with a spudger or your fingernail.

Agregar Comentario

Unscrew all four screws from the back of the PSP with the Phillips #00 Screwdriver. Two are located behind the battery's warranty sticker.
  • Unscrew all four screws from the back of the PSP with the Phillips #00 Screwdriver.

    • Two are located behind the battery's warranty sticker.

    • Two are located on the right side of the PSP.

Agregar Comentario

Next, unscrew the two screws located at the top of the PSP.
  • Next, unscrew the two screws located at the top of the PSP.

Agregar Comentario

Then, remove the single screw from the bottom edge of the PSP (which is positioned next to the barcode).
  • Then, remove the single screw from the bottom edge of the PSP (which is positioned next to the barcode).

Agregar Comentario

Slide the spudger in between the outer casing of the PSP, beginning at the "R" shoulder button, and gently pry off the casing.
 Remove the front casing completely.
  • Slide the spudger in between the outer casing of the PSP, beginning at the "R" shoulder button, and gently pry off the casing.


  • Remove the front casing completely.

Agregar Comentario

Push the homebar to the right to release the tab located on the right side of the LCD screen.
  • Push the homebar to the right to release the tab located on the right side of the LCD screen.

  • DO NOT completely remove the homebar, as it is still connected by ribbon cables.

Agregar Comentario

Slowly lift the LCD screen off the PSP starting at the top edge corner. Again, the LCD screen is attached by ribbon cables, so do not remove it completely.
  • Slowly lift the LCD screen off the PSP starting at the top edge corner.

  • Again, the LCD screen is attached by ribbon cables, so do not remove it completely.

    • Orientation of PSP is flipped in photo.

Agregar Comentario

Flip the small brown locks on the four ribbon cable connectors up using a spudger or fingernail. Pull all four ribbon cables out.
  • Flip the small brown locks on the four ribbon cable connectors up using a spudger or fingernail.

  • Pull all four ribbon cables out.

  • Now remove the LCD screen and homebar from the PSP.

Agregar Comentario

Remove the metal tab that lies above the LCD screen.
  • Remove the metal tab that lies above the LCD screen.

  • Upon reassembly, make note that the stamped lettering faces down, and the large tab fits just above the motherboard to the right hand side of the left trigger.

Agregar Comentario

Remove the screw securing 'L' trigger to the PSP.
  • Remove the screw securing 'L' trigger to the PSP.

Agregar Comentario

Remove the white plastic piece that holds the 'L' trigger in place.
  • Remove the white plastic piece that holds the 'L' trigger in place.

Agregar Comentario

Remove the 'L' trigger from the PSP.
  • Remove the 'L' trigger from the PSP.

Agregar Comentario

Remove the screw securing the 'R' trigger.
  • Remove the screw securing the 'R' trigger.

Agregar Comentario

Remove the white plastic piece that holds the 'R' trigger in place.
  • Remove the white plastic piece that holds the 'R' trigger in place.

Agregar Comentario

Remove the 'R' trigger from the PSP.
  • Remove the 'R' trigger from the PSP.

Agregar Comentario

Remove the screw from the bottom left edge of the PSP.
  • Remove the screw from the bottom left edge of the PSP.

Agregar Comentario

Being careful not to break the ribbon cable, use the spudger to peel the adhesive button of the the 'L' trigger off the PSP.
  • Being careful not to break the ribbon cable, use the spudger to peel the adhesive button of the the 'L' trigger off the PSP.

Being careful not to break the ribbon cable, use the spudger to peel the adhesive button of the 'L' trigger off the PSP.

buzinon - Contestar

Using a fingernail or spudger, flip up the retaining bracket on the d-pad and 'L' trigger ribbon cable. Lift the black plastic bracket along with the d-pad contact pad, disconnecting the ribbon cable as you lift.
  • Using a fingernail or spudger, flip up the retaining bracket on the d-pad and 'L' trigger ribbon cable.

  • Lift the black plastic bracket along with the d-pad contact pad, disconnecting the ribbon cable as you lift.

Agregar Comentario

Remove the cable from the connector and remove the entire black piece from the PSP.
  • Remove the cable from the connector and remove the entire black piece from the PSP.

Agregar Comentario

Remove the screw holding the analog stick in place.
  • Remove the screw holding the analog stick in place.

Agregar Comentario

Flip up the lock on the analog sticks ribbon cable. Remove the analog stick from the PSP.
  • Flip up the lock on the analog sticks ribbon cable.

  • Remove the analog stick from the PSP.

Agregar Comentario

Conclusión

To reassemble your device, follow these instructions in reverse order.

12 personas más completaron esta guía.

mbnewsom

Miembro Desde 28/10/09

2,357 Reputación

11 Guías creadas

Agregar Comentario

Ver Estadísticas:

Ultimas 24 Horas: 5

Últimos 7 Días: 23

Últimos 30 Días: 161

Todo El Tiempo: 16,975